Memorex DBVT1341 User Manual
OWNER’S MANUAL
MANUEL D'INSTRUCTIONS
COMBINATION 13" COLOR TELEVISION AND
VIDEO CASSETTE RECORDER
COMBINÉ TÉLÉVISEUR COULEUR 13" ET
MAGNÉTOSCOPE
DBVT1341
ATTENTION
If you purchase a universal remote control from your local retailer, please
contact the remote manufacturer for the required programming code.
Si vous utilisez avec cet appareil une télécommande universelle (autre que
celle vendue avec ce téléviseur), consultez la documentation accompagnant
la télécommande universelle afin de connaître le code numérique
correspondant au téléviseur.
ENGLISH
FRANÇAIS
When shipped from the factory, the TV/CATV menu option is set to the
“CATV”(Cable Television) mode.
If not using CATV, set this menu option to the “TV” position.
Lorsque l'appareil sort de l'usine, l'option du menu TV/CATV est réglée au
mode "CATV" (câblodistribution).
Si vous n'utilisez pas la câblodistribution, choisissez l'option "TV".
Before operating the unit, please read this manual thoroughly.
Avant de mettre cet appareil en marche, veuillez lire attentivement ce manuel.
5A30301A E COV. 04/10/2001, 18:001
TV/CATV MODE SELECTION
SELECTION DU MODE TV/CATV
ENGLISH
CAUTION:
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product's
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING:
CAUTION:
NOTE:
Please keep all packaging material for at least 90 days in case you need to return this product to your place of purchase
or Memorex.
WARNING:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED
TO PREVENT BLADE EXPOSURE.
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
CAUTION:
Changes or modifications not expressly approved by the
party responsible for compliance with the FCC Rules
could void the user's authority to operate this equipment.
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS
All the safety and operating instructions should be
read before the unit is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be
retained for future reference.
3. HEED WARNINGS
All warnings on the unit and in the operating
instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this unit from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning the exterior cabinet only.
6. ATTACHMENTS
The manufacturer of this unit does not make any
recommendations for attachments, as they may
cause hazards.
2
7. WATER AND MOISTURE
Do not use this unit near water. For example, near a
bathtub, washbowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool.
8. ACCESSORIES
Do not place this unit on an unstable cart, stand,
tripod, bracket, or table.
The unit may fall, causing serious injury, and
serious damage to the unit.
8A. An appliance and cart
combination should be
moved with care.
Quick stops, excessive
force, and uneven
surfaces may cause
the appliance and cart
combination to overturn.
PORTABLE CART WARNING
(symbol provided by RETAC)
S3126A
5A30301A E P02-11 04/10/2001, 18:002
IMPORTANT SAFEGUARDS
9. VENTILATION
Slots and openings in the cabinet back or bottom
are provided for ventilation, and to ensure reliable
operation of the unit, and to protect it from overheating. These openings must not be blocked or
covered. The openings should never be blocked by
placing the unit on a bed, sofa, rug, or other similar
surface. This unit should never be placed near or
over a radiator or heat source. This unit should not
be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have
been adhered to.
10. POWER SOURCES
This unit should be operated only from the type of
power source indicated on the rating plate. If you
are not sure of the type of power supply to your
home, consult your appliance dealer or local power
company. For units intended to operate from battery
power, or other sources, refer to the operating
instructions.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternatingcurrent line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet
only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
polarized plug, if your unit is equipped with a 3-wire
grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type
power outlet. This too, is a safety feature. If you are
unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the groundingtype plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are
not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
13. LIGHTNING
To protect your unit from a lightning storm, or when
it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent
damage to the unit due to lightning and power line
surges.
14. POWER LINES
An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside
antenna system, extreme care should be taken to
keep from touching such power lines or circuits, as
contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as
this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit,
as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never
spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected
to the unit, be sure the antenna or cable system is
grounded to provide some protection against
voltage surges and built-up static charges, Section
810 of the National Electrical Code, ANSI/NFPA 70,
provides information with respect to proper grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size
of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
18. SERVICING
Do not attempt to service this unit yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
ENGLISH
5A30301A E P02-11 04/10/2001, 18:003
3
IMPORTANT SAFEGUARDS
19. DAMAGE REQUIRING SERVICE
Unplug this unit from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operat-
ing instructions, as an improper adjustment of
other controls may result in damage and will
often require extensive work by a qualified
technician to restore the unit to its normal
operation.
e. If the unit has been dropped or the cabinet has
been damaged.
. When the unit exhibits a distinct change in
f
performance, this indicates a need for service.
20. REPLACEMENT PARTS
When replacement parts are required, be sure the
service technician uses replacement parts specified
by the manufacturer or those that have the same
characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock or other hazards.
21. SAFETY CHECK
Upon completion of any service or repairs to this
unit, ask the service technician to perform safety
checks to determine that the unit is in proper
operating condition.
22. WALL OR CEILING MOUNTING
The product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
23. HEAT
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
24. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
ELECTRIC SERVICE
EQUIPMENT
NEC-NATIONAL ELECTRICAL CODE
S2898A
4
5A30301A E P02-11 04/10/2001, 18:004
NATIONAL ELECTRICAL CODE
GROUND CLAMP
ANTENNA LEAD IN WIRE
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
PRECAUTIONS
MOISTURE CONDENSATION
DO NOT OPERATE ANY FUNCTIONS ON THIS UNIT
FOR AT LEAST TWO OR THREE HOURS WHEN
MOISTURE IN THE AIR CONDENSES ON IT. LET THE
UNIT STAND WITH POWER ON (SEE BELOW).
■ WHAT IS MOISTURE CONDENSATION?
When a cold liquid is poured into a glass, for example,
water vapor in the air will condense on the surface of
the glass. This is called moisture condensation.
■ MOISTURE WILL CONDENSE ON THE UNIT IN
THE FOLLOWING CASES:
• When you move the unit from a cold to a warm place.
• After heating a cold room or under extremely humid
conditions.
■ WHEN YOU EXPERIENCE THE ABOVE CONDI-
TIONS,
Plug the power cord into an AC outlet, press the
POWER button to turn on and leave the unit at room
temperature until moisture condensation disappears.
Depending on the surrounding conditions, this may
take two or three hours.
LOCATION AND HANDLE
• If you cause a static discharge when touching the unit,
and the unit fails to function, simply unplug the unit
from the wall outlet, wait 10 minutes and plug it back in.
The unit should return to normal operation.
• Avoid extreme heat or cold.
• Do not place the unit on or near appliances which may
cause electromagnetic interference (e.g. speakers,
etc). Doing so may cause erratic operation of the unit
including picture and/or sound distortion or noise.
• Avoid extreme moisture and dust.
• The ventilation holes prevent overheating. Do not
block or cover these holes. Especially avoid covering
the holes with soft materials such as cloth or paper.
• Do not insert fingers or any other objects into the
cassette loading slot. Do not spray cleaner or wax
directly on the unit or use forced air to remove dust.
• Avoid places subject to strong vibration. Use in a
horizontal (flat) position only.
• Keep the unit away from flower vases, sinks, etc.
If liquids should be spilled into the unit, serious damage
will result. If you spill any liquids into the unit, unplug the
AC power cord immediately and consult qualified
service personnel before attempting to use it again.
• When you finish operating the unit, always unload the
cassette and turn off the power.
• When you leave your home for a long time, unplug the
AC power cord.
• To protect the unit from a lightning storm, unplug the
AC power cord from the wall outlet and disconnect the
antenna.
POWER SOURCE
Use the AC polarized line cord provided for operation on
AC. Insert the AC cord plug into a standard 120V 60Hz
polarized AC outlet.
NOTES: • Never connect the AC line cord plug to
anything other than the specified voltage (120V
60Hz). Use the attached power cord only.
• If the polarized AC cord does not fit into a
nonpolarized AC outlet, do not attempt to file
or cut the blade. It is the user's responsibility
to have an electrician replace the obsolete
outlet.
AC Outlet
Wider Hole
and Blade
Polarized AC Cord Plug
(One blade is wider than the other.)
ENGLISH
5A30301A E P02-11 04/10/2001, 18:005
5
PRECAUTIONS
FEATURES
BATTERY INSTALLATION
Slide the battery compartment cover.
Install two “AAA” batteries (not supplied), paying
attention to the polarity diagram in the battery compartment.
Replace the compartment cover.
BATTERY PRECAUTIONS
The precautions below should be followed when using
batteries in this device:
1 Use only the size and type of batteries specified.
2 Be sure to follow the correct polarity when installing
the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
3 Do not mix different types of batteries together (e.g. Al-
kaline and Carbon-zinc) or old batteries with fresh ones.
4 If the device is not to be used for a long period of time,
remove the batteries to prevent damage or injury from
possible battery leakage.
5 Do not try to recharge batteries not intended to be
recharged; they can overheat and rupture (Follow
battery manufacturer’s directions).
EFFECTIVE DISTANCE OF THE
REMOTE CONTROL
Color TV With Video Cassette Recorder - Unique space
saving design combines a color TV and a video cassette
recorder.
High Quality Picture Technology - This TV/VCR equipped
“HQ” incorporates VHS High Quality technology. A built-in
detail enhancer is used to boost the recorded signal and
provide maximum picture quality during playback. It is
compatible with other VHS video cassette recorders.
181 Channel Tuner - Receives standard VHF and UHF
broadcast channels and up to 113 cable channels. The
actual number of channels received depends upon channel
reception in your area or your cable system.
Closed Caption Decoder With Full Text Mode - Displays
text captions or full screen text on the screen for hearing
impaired viewers.
8-Programs/1-Month Programmable Timer With Everyday/Every Week Capability - The built-in timer allows
automatic absentee recording of up to 8 TV programs within
1 month. It is also possible to record a program which is
broadcast at the same time everyday or every week.
Automatic Clock Set - Once your TV/VCR is connected to
an antenna or Cable TV, and also connected into the AC
outlet, it automatically sets the correct date and time.
On-Screen TV Display And VCR Programming - When
you select a channel or make other changes, the TV will
show an indicator on the screen for a few seconds. Timer
recording can be programmed and confirmed on the screen.
Picture Adjustments Using The Remote Control - The
On-Screen display allows precise remote control adjustment
of BRIGHTNESS, CONTRAST, COLOR, TINT and SHARPNESS.
15 PIES (5m)
15 FEET
30˚
30˚
NOTES: • When there is an obstacle betw een the TV/VCR
and the remote control, the remote control may
not operate.
• When direct sunlight, an incandescent lamp,
fluorescent lamp or any other strong light
shines on the Remote sensor of the TV/VCR,
the remote operation may be unstable.
6
5A30301A E P02-11 04/10/2001, 18:006
Automatic Playback/Rewind-Stop-Eject - When loading a
cassette tape without the erase prevention tab, this TV/VCR
will automatically play back the cassette tape at the correct
speed. When a tape reaches its end during play-back,
recording
forward, it will automatically stop, rewind, stop and eject the
tape.
Programmable ON/OFF Timer - Allows you to automatically
turn on or off the TV/VCR at a set time.
Programmable TV Sleep Timer - Operable from the remote
control, the TV can be programmed up to 120 minutes to turn
off automatically.
(except during OTR and Timer Record) and fast
TABLE OF CONTENTS
Automatic Repeat Play System - When Auto Repeat option
is turned on, the TV/VCR will automatically play back the
same cassette tape repeatedly.
One-touch Timer Recording (OTR) - Simply by pressing
the REC/OTR button, the TV/VCR can be programmed for
up to 5 hours of recording with an immediate start.
Audio/Video Input Jacks - A VCR or other video device
may be hooked up to this TV/VCR for dubbing or playback
purposes.
Skip Search - When the SKIP SEARCH button on the
remote control is pressed during playback, the TV/VCR will
automatically search forward in 30 second increments to a
maximum of 3 minutes with each press of the SKIP SEARCH
button, and then return to normal playback.
2 Speed Picture Search - 3 or 5 times normal speed in SP
mode (7X or 9X in LP and 9X or 15X in SLP).
3 Speed Playback - Plays three tape speeds (SP, LP, SLP).
2 Speed Record - Records two tape speeds (SP, SLP).
Real Time Tape Counter With Zero Return - The counter
displays the real tape time and the zero return can be used
to return the tape to a pre-selected position (00:00:00) while
the counter can be used to locate programs.
Digital Auto Tracking - Automatically adjusts tracking
during playback for the best possible picture.
On-Screen 3 Language Display - You can select one of 3
languages, English, Spanish or French for on-screen
programming.
TV Monitor - When the TV MONI. button on the remote
control is pressed during playback, the TV channel selected
on the TV/VCR can be viewed.
V-Chip - The V-Chip function can read the rating of a TV
program or movie content if the program is encoded with this
information. V-chip will allow you to set a restriction level.
CAUTIONS
IMPORTANT SAFEGUARDS ..................................... 2
PRECAUTIONS .......................................................... 5
PREPARATION
FEATURES................................................................. 6
LOCATION OF CONTROLS ....................................... 8
REMOTE CONTROL .................................................. 9
ANTENNA CONNECTIONS ..................................... 10
CABLE TV CONNECTIONS ..................................... 11
SETTING THE LANGUAGE ..................................... 11
AUTO CLOCK SETTING .......................................... 12
MANUAL CLOCK SETTING ..................................... 13
TV OPERATION
TV OPERATION ....................................................... 13
TO MEMORIZE CHANNELS .................................... 15
SETTING THE V-CHIP ............................................. 16
TO SET THE ON TIMER .......................................... 17
TO SET THE OFF TIMER......................................... 18
PICTURE CONTROL ADJUSTMENTS .................... 18
PLAYBACK
LOADING AND UNLOADING .....................................
PLAYBACK ............................................................... 19
SPECIAL PLAYBACK ............................................... 20
19
RECORDING
RECORDING A TV PROGRAM................................ 20
ONE-TOUCH TIMER RECORDING (OTR) .............. 21
TIMER RECORDING ................................................ 21
ADDITIONAL INFORMATION
USING THE REAL TIME TAPE COUNTER.............. 22
USING ZERO RETURN ........................................... 22
DUPLICATING A VIDEO TAPE................................. 23
TROUBLESHOOTING GUIDE ................................. 24
RECEPTION DISTURBANCES ................................ 26
VIDEO HEAD CLEANING ........................................ 26
SPECIFICATIONS .................................................... 27
LIMITED WARRANTY .............................................. 28
ENGLISH
5A30301A E P02-11 04/10/2001, 18:007
7
LOCATION OF CONTROLS
REARFRONT
1
Phones Power
9
Volum e
3104 5
Channel
Stop/
Eject
11
Rew Play F.Fwd
12 13
Rec/Otr
2
8
6
7
Rec/Otr
T-Re c
Video – In – Audio
14
DESCRIPTION OF CONTROLS
FRONT:
1. Cassette Loading Slot - To insert or remove a
video tape.
2. POWER Button - Press to turn the TV/VCR on or off.
3. STOP/EJECT Button - Press once to stop the tape
in any mode. Press again to eject the tape.
4. PLAY Button - Press to play a prerecorded tape.
5. REC/OTR Button - Press once to start normal
recording. Additional presses activate One-touch
Timer Recording.
6. Remote Sensor - Signals from the Remote Control
are received here.
7. REC/OTR Indicator - Lights when the TV/VCR is
recording.
8. T-REC Indicator - This lights when the TIMER REC
button is pressed.
9. PHONES Jack - Plug monaural headphones or an
earphone with an 1/8" miniplug into this jack for
private listening.
10. VOLUME ▲ / ▼ Buttons - Press to raise or lower
the volume of the sound.
ANT.
CHANNEL ▲ / ▼ Buttons -
11.
15
16
Press to select a
channel for viewing or recording.
12. REW (Rewind) Button - In the Stop mode, this
button rapidly winds the tape backwards. In the Play
mode, this button activates reverse search.
13. F.FWD (Fast Forward) Button - In the Stop mode,
this button rapidly winds the tape forward. In the
Play mode, this button activates forward search.
14. Audio/Video In Jacks - Audio and video signal
cables from an external source can be connected
here.
REAR:
15. VHF/UHF Antenna Jack - Connect the 75 ohm
coaxial cable from the antenna or Cable TV service
to this jack.
16. AC Power Cord - Connect to a 120V, 60Hz outlet.
8
5A30301A E P02-11 04/10/2001, 18:008
REMOTE CONTROL
1
2
3
4
5
6
7
8
POWER SLEEP TV MONI. EJECT
123
456
7809
QUICK VIEW
CALL
REC/OTR
PLAY
SPEED
STOP
SET/TRACKING
– +
MENU
AUTO
TV/CAP/
TRACKING
TEXT
PROGRAM
COUNTER
SKIP
RESET
SEARCH
CHANNEL
VOLUME
MUTINGINPUT SELECT
PAUSE/STILL
ENTER
CANCEL
TIMER REC
ZERO
RETURN
+
–
+
–
F.FWDREW
10
11
12
13
14
15
16
9
DESCRIPTION OF CONTROLS
1. POWER Button - Press to turn the TV/VCR on.
Press again to turn the TV/VCR off.
2. Direct Channel Selection Buttons (0-9) - Allows
direct access to any channel.
3. CALL Button - Displays the present time/day of the
week, channel, counter, speed selection (and VCR
mode if VCR is playing) on the TV screen.
4. REC/OTR Button - Press once to start normal
recording. Additional presses activate One-touch
Timer Recording.
5. REW (Rewind) Button - In the Stop mode, this
button rapidly winds the tape backwards. In the Play
mode, this button activates reverse search.
6. SPEED Button - Sets the tape speed for recording.
7. MENU Button - Press to display the On-Screen
menu function.
8. PROGRAM Button - Press to confirm the pro-
grammed timer recording and ON/OFF timer.
9. SKIP SEARCH Button - Press in the playback
mode to search forward in 30 second increments to
a maximum of 3 minutes.
10. TV MONI. Button - Used to temporarily view a TV
channel selected on the TV/VCR while in the
playback mode.
11. CHANNEL Up / Down Buttons - Press the Up
button to change to a higher numbered channel set
into memory. Press the Down button to change to a
lower numbered channel set into memory.
12. QUICK VIEW Button - Switches between the present
channel and the last channel selected.
13. MUTING Button - Press to turn off the sound.
Press again to turn the sound back on.
14. F.FWD (Fast Forward) Button - In the Stop mode,
this button rapidly winds the tape forward. In the
Play mode, this button activates forward search.
2217
POWER SLEEP TV MONI. EJECT
18
19
20
21
123
456
7809
CALL
REC/OTR
SPEED
MENU
PROGRAM
QUICK VIEW
PLAY
STOP
SET/TRACKING
– +
AUTO
TV/CAP/
TRACKING
COUNTER
SKIP
RESET
SEARCH
CHANNEL
+
–
VOLUME
+
–
MUTINGINPUT SELECT
PAUSE/STILL
F.FWDREW
ENTER
CANCEL
TIMER REC
TEXT
ZERO
RETURN
23
24
25
26
27
28
29
15. AUTO TRACKING Button - Allows automatic
adjustment of tracking to minimize picture noise
during playback.
16. TV/CAP/TEXT Button - Switches between Caption,
Text and TV modes for Closed-Captioned programs.
17. SLEEP Button - Sets the TV to turn off automati-
cally after up to 120 minutes.
18. INPUT SELECT Button - Switches the program for
viewing between the TV/VCR and external input
sources.
19. PLAY Button - Press to play a prerecorded tape.
20. SET/TRACKING + / – Buttons - Used to set or
adjust in the menu mode. During playback, they are
used to adjust tracking manually.
21. COUNTER RESET Button - Used to reset the
counter to 00:00:00.
22. EJECT Button - Press to eject the tape.
23. VOLUME Up / Down Buttons - Press the Up
button to increase, or the Down button to decrease
the volume level.
24. PAUSE/STILL Button - During recording, this
button temporarily stops the tape. During playback,
it stops the tape and displays a still image on the TV
screen.
25. STOP Button - Press once to stop the tape.
26. ENTER Button - Press to enter or select information
for on-screen operations.
27. CANCEL Button - Used to clear the selected
program and to move the cursor backward.
28. TIMER REC Button - Used to set the TV/VCR to
start recording at a preset time (Timer program must
be set).
29. ZERO RETURN Button - Use to stop the tape
when the counter reaches 00:00:00.
ENGLISH
9
5A30301A E P02-11 04/10/2001, 18:009
ANTENNA CONNECTIONS
If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna
system. If you are using a cable TV service (CATV), see page 11 for Cable TV connections.
Combination VHF/UHF Antenna (Single 75 ohm cable or 300 ohm twin-lead wire
Connect the 75 ohm cable from the combination VHF/UHF antenna to the Antenna Jack. If your combination VHF/
UHF antenna has a 300 ohm twin-lead wire, the use of the 300-75 ohm Matching Transformer may be necessary.
Connect the VHF 75 ohm cable and UHF 300 ohm.
Antenna Jack Antenna Jack
75 ohm
Coaxial
Cable
ANT
300-75 ohm Matching Transformer
ANT
)
Combination VHF/UHF Antenna (Separate VHF and UHF 300 ohm twin-lead wires
Connect the UHF 300 ohm twin-lead wire to the Combiner (not supplied). Connect the VHF 300 ohm twin-lead wire
to the 300-75 ohm Matching Transformer. Attach the Transformer to the Combiner, then attach the Combiner to the
Antenna Jack.
Antenna Jack
ANT
Combiner
UHF 300 ohm
300-75 ohm Matching
Transformer
VHF 300 ohm
Separate VHF/UHF Antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires
Connect the VHF 75 ohm cable and UHF 300 ohm twin-lead wire to the Combiner (not supplied). Attach the
Combiner to the Antenna Jack.
)
)
10
5A30301A E P02-11 04/10/2001, 18:0010
Antenna Jack
ANT
Combiner
UHF 300 ohm
VHF 75 ohm
CABLE TV CONNECTIONS
ANT
ANT
This TV/VCR has an extended tuning range and can tune most cable channels without using a Cable TV
converter box. Some cable companies offer "premium pay channels" in which the signal is scrambled.
Descrambling these signals for normal viewing requires the use of a descrambler device which is generally
provided by the cable company.
FOR SUBSCRIBERS TO BASIC CABLE TV SERVICE
For basic cable service not requiring a Converter/Descrambler box,
connect the CATV 75 ohm Coaxial Cable directly to the Antenna Jack
on the back of the TV/VCR.
75 ohm
Coaxial Cable
FOR SUBSCRIBERS TO SCRAMBLED CABLE TV SERVICE
If you subscribe to a cable TV service which requires the use of a Converter/Descrambler box, connect the incoming
75 ohm Coaxial Cable to the Converter/Descrambler box. Using another 75 ohm Coaxial Cable, connect the output jack
of the Converter/Descrambler box to the Antenna Jack on the TV/VCR. Follow the connections shown below. Set the
TV/VCR to the output channel of the Converter/Descrambler box (usually channel 3 or 4) and use the Converter/
Descrambler box to select channels.
Incoming 75 ohm
CATV cable
Converter/Descrambler
75 ohm Cable to TV/VCR
FOR SUBSCRIBERS TO UNSCRAMBLED BASIC CABLE TV SERVICE WITH
SCRAMBLED PREMIUM CHANNELS
If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the
use of a Converter/Descrambler box, you may wish to use a signal splitter and an A/B Switch box (available from the
Cable company or an electronics supply store). Follow the connections shown below. With the switch in the "B"
position, you can directly tune any nonscrambled channels on your TV/VCR. With the switch in the "A" position, tune
your TV/VCR to the output of the Converter/Descrambler box (usually channel 3 or 4) and use the Converter/
Descrambler box to tune scrambled channels.
Antenna Jack
ANT
Antenna Jack
ENGLISH
Incoming
Converter/Descrambler
75 ohm
CATV cable
Splitter
A/B Switch
SETTING THE LANGUAGE
This TV/VCR can display the on screen language in
English, Spanish or French.
On-screen language selection (step 3) will automatically appear on the screen when you press the MENU
button initially. Select the language you prefer first,
then proceed with the other menu options.
1 Press the MENU button.
Press the SET/TRACKING + or –
button to select the SYSTEM
SET-UP option, then press the
ENTER button.
5A30301A E P02-11 04/10/2001, 18:0011
M E N U
TIMER REC SET
TV SET-UP
CH SET-UP
AUTO REPEAT ON OFF
SYSTEM SET-UP
〈
+/–/ENTER/MENU
〉
75 ohm cable
B
to TV/VCR
A
2 Press the SET/TRACKING + or
– button to select the LANGUAGE option, then press the
ENTER button.
3 Press the SET/TRACKING + or
– button to select the desired
language: English (ENGLISH),
Spanish (ESPAÑOL) or French
(FRANCAIS), then press the
ENTER button.
4 Press the MENU button until the
MENU screen is cleared.
Antenna Jack
SYSTEM SET-UP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
AUTO CLOCK ON OFF
STANDARD TIME
DAYLIGHT SAVING TIME
〈
+/–/ENTER/MENU
LANGUAGE/IDIOMA/LANGUE
ENGLISH
ESPAÑOL
FRANCAIS
〈
+/–/ENTER/MENU
〉
〉
11
AUTO CLOCK SETTING
The Auto Clock function will automatically set the
built-in clock (Month, Day, Year and Time) when the
TV/VCR is connected to an Antenna or Cable system
and it is turned off. As the TV/VCR searches for a
receivable station in your area, it will also receive a
broadcast signal for Auto Clock which will automatically set the clock and date.The Auto Clock needs
several minutes to set itself.
AUTO CLOCK SETTING
1 Connect the Antenna or Cable system.
• If you use a cable box, turn it on.
2 Plug the AC Power cord to the AC outlet.
3 Make sure the TV/VCR is turned off.
• If you press the POWER button, the Auto Clock set is
not effective.
4 Wait at least three minutes and press the POWER
button.
5 Press the CALL button to check the clock on the screen.
6 If the clock is not set, check the Antenna condition. The
Auto Clock may not function properly if the reception
condition is not good.
AUTO CLOCK ADJUSTMENT
The Auto Clock Adjustment will be performed at 12:00 PM
everyday if you turn off the TV/VCR.
• If you use a cable box and you want Auto Clock adjust-
ment to be performed, the cable box must be left on.
• The Auto Clock Adjustment is not effective when there
is a difference of more than 5 minutes between the
built-in clock time and the actual time.
TO SET AUTO CLOCK TO OFF
When shipped from factory the AUTO CLOCK option is
set to ON.
But if you do not want Auto Clock set (Adjustment):
1 Turn on the TV/VCR.
2 Press the MENU button.
3 Press the SET/TRACKING + or – button to select the
SYSTEM SET-UP option, then press the ENTER
button.
4 Press the SET/TRACKING + or – button to select the
AUTO CLOCK option.
5 Press the ENTER button to select OFF.
6 Press the MENU button repeatedly to return to the
normal screen.
• When the AUTO CLOCK is set to OFF, the Auto Clock
adjustment does not function.
• Set the clock manually (see page 13).
TO SET STANDARD TIME
In the rare event that you live within broadcast range of
two stations in two different time zones, the TV/VCR
may recognize the wrong station for the Auto Clock set.
To correct the situation:
1 Press the MENU button.
2 Press the SET/TRACKING + or – button to select the
SYSTEM SET-UP option, then press the ENTER button.
3 Press the SET/TRACKING + or – button to select the
STANDARD TIME option, then Press the ENTER button.
4 Press the SET/TRACKING + or – button to select your
time zone, then press the ENTER button.
ATLANTIC : GMT – 4 hours
(GMT: Greenwich Mean Time)
EASTERN : GMT – 5 hours
CENTRAL : GMT – 6 hours
MOUNTAIN : GMT – 7 hours
PACIFIC : GMT – 8 hours
ALASKA : GMT – 9 hours
HAWAII : GMT – 10 hours
AUTO : AUTO SET
5 Press the MENU button twice to return to the normal
screen.
NOTES: • To be able to select the standard time, the
clock must first be set by “AUTO CLOCK” once.
• If you live in Newfoundland and the Auto
Clock does not function properly, set the
AUTO CLOCK menu option to OFF and set
the clock manually.
DAYLIGHT SAVING TIME SETTING
You can set the Daylight saving time automatically or
manually.
1 Press the MENU button. Press
the SET/TRACKING + or – button
to select the SYSTEM SET-UP
option, then press the ENTER
button.
2 Press the SET/TRACKING + or –
button to select the DAYLIGHT
SAVING TIME option, then press
the ENTER button.
3 Press the SET/TRACKING + or –
button to select one of the
options, then press the ENTER
button. Press the MENU button
until the MENU screen is cleared.
ON: for manual setting
(forward one hour)
OFF: for manual setting
(back one hour)
AUTO: for automatic setting
(read XDS in the signal)
When you want to set the Daylight Saving Time manually,
on the first Sunday in April you set to “ON”, and on the last
Sunday in October you set to “OFF”.
NOTES: • When shipped from factory, the DAYLIGHT
SAVING TIME option is set to AUTO position.
• When the clock is not set, Daylight Saving
Time setting is not available.
• When there is no Daylight Saving Time in your
area, always select OFF position in step 3.
M E N U
TIMER REC SET
TV SET-UP
CH SET-UP
AUTO REPEAT ON OFF
SYSTEM SET-UP
〈
+/–/ENTER/MENU
〈
+/–/ENTER/MENU
DAYLIGHT SAVING TIME
〈
+/–/ENTER/MENU
〉
SYSTEM SET-UP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
AUTO CLOCK ON OFF
STANDARD TIME
DAYLIGHT SAVING TIME
〉
ON
OFF
AUTO
〉
12
5A30301A E P12-19 04/10/2001, 18:0112
MANUAL CLOCK SETTING
TV OPERATION
You must set the date and time manually for Timer
Recordings, ON/OFF Timer and Daylight Saving Time
if the Auto Clock process did not set them correctly.
EXAMPLE: Setting the clock to “8:30 AM”, 29th (FRI)
March, 2002.
1 Press the MENU button.
Press the SET
button to select the SYSTEM
SET-UP option, then press the
ENTER button.
/TRACKING
+ or –
2 Press the SET/TRACKING + or –
button to select the CLOCK SET
option, then press the ENTER
button.
3 Press the SET/TRACKING + or –
button to set the month, then press
the ENTER button.
4 Set the day, year and time as in
step 3.
After setting the clock, time and date,
the time starts functioning automatically.
M E N U
TIMER REC SET
TV SET-UP
CH SET-UP
AUTO REPEAT ON OFF
SYSTEM SET-UP
〈
+/–/ENTER/MENU
〈
+/–/ENTER/MENU
CLOCK SET
〈
+/–/ENTER/CANCEL/MENU
CLOCK SET
〈
+/–/ENTER/CANCEL/MENU
〉
SYSTEM SET-UP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
AUTO CLOCK ON OFF
STANDARD TIME
DAYLIGHT SAVING TIME
〉
MONTH
3
DAY
1 (WED)
YEAR
2000
TIME
12 : 00 AM
MONTH
3
DAY
29 (FRI)
YEAR
2002
TIME
8 : 30 AM
8 : 30 AM FRI
NOTES: • After a power failure or disconnection of the
power plug, the time display will be lost. In
this case, set the present time again if the
Auto Clock did not set correctly.
• To move cursor backward, press the CANCEL
button.
1 To turn on the TV/VCR, press the POWER button.
2 Adjust the volume level by
pressing the VOLUME Up or Down
button. The volume level will be
indicated on the screen by green
bars. As the volume level
VOLUME 32
increases, so do the number of
bars. If the volume decreases, the number of green
bars also decreases.
3 Set the TV/CATV menu option to the appropriate
position (See page 15).
TV - VHF/UHF Channels
CATV - CABLE TV Channels
VHF/UHF/CATV CHANNELS
TV CATV
VHF
2-13
UHF
14-69
〉
VHF
2-13
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100)(125)
01 (5A)
4 Press the Direct Channel selection buttons to select
the channel.
〉
• TV mode direct channel selection
When the TV/CATV menu option is in the TV
position, all channels can be instantly selected by
using two buttons (for example, to select channel 2,
press "0", then "2". If you press only "2", channel
selection will be delayed for a few seconds). For
channels 10 and above, press the 2 digits in order.
• CATV mode direct channel selection
When the TV/CATV menu option is in the CATV
position, channels can be selected as follows:
• TO SELECT CATV CHANNELS:
1-9 Press "0" twice, then 1-9 as needed.
10-12 Press "0", then the remaining 2 digits.
13-99 Press the 2 digits in order.
100-125 Press the 3 digits in order.
NOTE FOR CHANNELS 1-12:
If only 1 or 2 buttons are pressed,
the corresponding channel will be
selected in 2 seconds.
Example, to select channel 2, press "002".
Example, to select channel 12, press "012".
Example, to select channel 36, press "36".
Example, to select channel 120, press "120".
ENGLISH
CH 012
5A30301A E P12-19 04/10/2001, 18:0113
NOTES: •If a channel with no broadcast is selected,
the sound will automatically be muted.
• If a station being viewed stops broadcasting,
the TV will automatically shut itself off after
15 minutes.
13
TV OPERATION
MUTING
Press MUTING button to switch off
the sound. The TV/VCR’s sound will
be silenced and “MUTING” will
briefly appear on the screen. The
sound can be switched back on by
pressing this button again or one of
the VOLUME Up or Down buttons.
Press and release the CHANNEL
Up or Down button. The channel
automatically stops at the next
channel set into memory. For proper
operation, before selecting channels, they should be set into the
memory.
See pages 15 and 16 “To memorize channels”.
MUTING
CH 012
CALL
Press the CALL button. The clock, date, channel number,
real time tape counter, tape speed and VCR operation will
be indicated.
Press CALL button again to remove the call display.
Current time
8:47AM THU CH 012
00:04:38 SP
Real Time Counter
NOTE: To listen through the headphone, insert a
headphone (not supplied) with a 1/8" mini plug
into the PHONES jack on the front. The sound
from the TV speaker is muted.
Channel No.
Auto Repeat
Tape In
Tape Speed
VCR operation
: Play
: Rewind
: Fast-forward
: Eject
: Recording
: Pause
: Stop
SLEEP
To set the TV/VCR to turn off after a preset amount of
time, press the SLEEP button on the remote control.
The clock will count down 10 minutes for each press of
the SLEEP button (120, 110, ...10, 0). After the sleep time
is programmed, the display will appear briefly every ten
minutes to remind you that the sleep timer is operating.
To confirm the sleep timer setting,
press the SLEEP button and the
remaining time will be momentarily
displayed. To cancel the sleep timer,
press the SLEEP button repeatedly
until the display turns to 0.
SLEEP
120
QUICK VIEW
This button allows you to go back
to the last channel selected by
pressing the QUICK VIEW button.
Press this button again to return to
the last channel you were watching.
CH 012
TV/CAPTION/TEXTCHANNEL UP / DOWN
Press TV/CAP/TEXT button to
switch between normal TV and the
two closed caption modes (captions
and full screen text). Closed
captioning will display text on the
screen for hearing impaired viewers.
NOTES:
• If using an indoor antenna or if TV reception
is very poor, the Closed Caption Decoder text
may not appear. In this case, adjust the
antenna for better reception or use an outdoor
antenna.
• When activating the Closed Captioned
Decoder, there will be a short delay before
the Closed Captioned text appears on the
screen.
• Closed Captioned TV programs can be
recorded and played back on a VCR with the
Closed Captioned text intact. The Closed
Captioning text will disappear during Cue,
Rewind and Pause modes or if the VCR
tracking is not adjusted properly.
• Closed Captioned text is only displayed in
locations where it is available.
• If the Call display is on, the Closed Captioning
text will not appear.
WHAT IS CLOSED CAPTIONING?
This television has the capability to decode and display
Closed Captioned television programs. Closed Captioning
will display text on the screen for hearing impaired
viewers or it will translate and display text in another
language.
CLOSED CAPTIONING WITH A VCR
Closed Captioned programs can be recorded and played
back on a VCR with the Closed Captioned text intact.
The Closed Captioned text will disappear during Cue
(Fast Forward Search), Review (Rewind Search) and
Pause Modes or if the VCR tracking is not adjusted
properly.
TO VIEW CLOSED CAPTIONS
Press the TV/CAP/TEXT button on the remote control to
switch between normal TV and the two Closed Caption
Modes (Captions and Full Screen Text).
CAPTION CH 1
14
5A30301A E P12-19 04/10/2001, 18:0114
Captions: This Closed Caption Mode will display text on
the screen in English or another language (depending
on the setting of the Closed Captions CH. 1 or 2).
Generally, Closed Captions in English are transmitted on
Captions Channel 1 and Closed Captions in other
languages are transmitted on Captions Channel 2.
Tex t: The Text Closed Caption Mode will usually fill the
screen with a programming schedule or other information.
After selecting a Closed Caption Mode, it will stay in
effect until it is changed, even if the channel is changed.
If the Captions signal is lost due to a commercial or a
break in the signal, the Captions will reappear when the
signal is received again. If the channels are changed,
the Captions will be delayed approximately 10 seconds.
The Captions will appear in places on the screen where
they will least interfere with the picture, usually on the
bottom of the screen. News programs will usually show
three-line Closed Captions which scroll onto the screen.
Most other shows provide two or three lined Captions
placed near the character who is speaking so the viewer
can follow the dialogue.
Words in italics or underlined describe titles, words in
foreign languages or words requiring emphasis. Words
that are sung usually appear enclosed by musical notes.
For television programs broadcasting with Closed Captions, look in your TV guide for the Closed Captions
symbol (CC).
TO MEMORIZE CHANNELS
This TV/VCR is equipped with a channel memory
feature which allows channels to skip up or down to
the next channel set into memory, skipping over
unwanted channels. Before selecting channels, they
must be programmed into the TV/VCR’s memory. In
addition to normal VHF and UHF channels, this TV/
VCR can receive up to 113 Cable TV channels. To
use this TV/VCR with an antenna, set the TV/CATV
menu option to the TV mode. When shipped from the
factory, this menu option is in the CATV mode.
TV/CATV SELECTION
1 Press the MENU button.
2 Press the SET/TRACKING + or
– button to select the CH SET-UP
mode, then press the ENTER
button.
VHF/UHF/CATV CHANNELS
TV
VHF
2-13
UHF
14-69
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100)(125)
M E N U
TIMER REC SET
TV SET-UP
CH SET-UP
AUTO REPEAT ON OFF
SYSTEM SET-UP
〈
+/–/ENTER/MENU
CATV
VHF
2-13
01 (5A)
〉
ENGLISH
• When selecting Closed Captions, the captioning will
be delayed approximately 10 seconds.
• If no caption signal is received, no captions will
appear, but the television will remain in the Caption
Mode.
• When Captions are being displayed, on-screen
displays, such as volume and mute may not be seen
or may interfere with Closed Captions.
• Misspellings or unusual characters may occasionally
appear during Closed Captioning. This is normal with
Closed Captioning, especially with live programs. This
is because during live programs, captions are also
entered live. These transmissions do not allow time for
editing.
• Some cable systems and copy protection systems
may interfere with the Closed Captioned signal.
• If using an indoor antenna or if TV reception is very
poor, the Closed Caption Decoder may not appear or
may appear with strange characters or misspelled
words. In this case, adjust the antenna for better
reception or use an outdoor antenna.
3 Press the SET/TRACKING + or
– button to select the TV/CATV
mode.
4 Press the ENTER button to
select the TV or CATV mode.
CH SET-UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
〈
+/–/ENTER/MENU
〉
The arrow indicates the selected
mode.
TV - VHF/UHF channels
CATV - CABLE TV channels
5 Press the MENU button until the MENU screen is cleared.
AUTOMATIC MEMORY TUNING
1 Press the MENU button.
2 Press the SET/TRACKING + or
– button to select the CH SET-UP
mode, then press the ENTER
button.
3 Press the SET/TRACKING + or
– button to select the AUTO CH
MEMORY mode, then press the
ENTER button. The TV/VCR will
begin memorizing all the channels available in your area.
Channel numbers will remain red
until auto memorizing is complete.
4 Press the MENU button until the MENU screen is
cleared.
M E N U
TIMER REC SET
TV SET-UP
CH SET-UP
AUTO REPEAT ON OFF
SYSTEM SET-UP
〈
+/–/ENTER/MENU
〈
+/–/ENTER/MENU
〉
CH SET-UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
〉
15
5A30301A E P12-19 04/10/2001, 18:0115
TO MEMORIZE CHANNELS
SETTING THE V-CHIP
TO ADD/DELETE CHANNELS
1 Press the MENU button.
2 Press the SET/TRACKING + or
– button to select the CH SET-UP
mode, then press the ENTER
button.
3 Press the SET/TRACKING + or
– button to select the ADD/
DELETE mode, then press the
ENTER button.
4 Select the desired channel to be
memorized or deleted using SET/
TRACKING + or – button, or
using the Direct Channel.
Selection buttons (10 keys, 0-9),
or CHANNEL Up or Down button.
5 Press the ENTER button to
select the ADD or DELETE.
If you select an unmemorized channel, the Channel
indication will be red. If you select the ADD mode, the
Channel indication changes from red to green and the
channel will be memorized. If you select a memorized
channel, the Channel indication will be green. If you
select the DELETE mode, the Channel indication
changes from green to red and the channel will be
deleted from the memory.
6 Press the MENU button until the MENU screen is
cleared.
M E N U
TIMER REC SET
TV SET-UP
CH SET-UP
AUTO REPEAT ON OFF
SYSTEM SET-UP
〈
+/–/ENTER/MENU
〈
+/–/ENTER/MENU
〈
0–9/+/–/ENTER/MENU
〉
CH SET-UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
〉
CH 003ADD
〉
SETTING THE V-CHIP
An age limitation can be set to forbid children to see
and hear the programs including violent scenes or
pictures for adults, etc. The TV/VCR responds to "TV
RATING" and "MOVIE RATING". To use the V-Chip
function, you must register a password.
1 Press the MENU button.
2 Press the SET/TRACKING + or –
button to select the TV SET-UP
option, then press the ENTER
button.
3 Press the SET/TRACKING + or –
button to select the V-CHIP SET
then press the ENTER button.
4 Enter the password (4 digits) us-
ing the Direct Channel Selection
buttons (0-9), then press the ENTER button.
" "appears instead of the number.
5 Enter the same password again
for safety, then press the ENTER
M E N U
TIMER REC SET
TV SET-UP
CH SET-UP
AUTO REPEAT ON OFF
SYSTEM SET-UP
〈
+/–/ENTER/MENU
〈
+/–/ENTER/MENU
V-CHIP SET
〈
0–9/ENTER/CANCEL/MENU
TV SET-UP
V-CHIP SET
ON/OFF TIMER
PICTURE
NEW
PASSWORD:
〉
〉
button.
16
V-CHIP SET menu appears.
NOTES:
When you dislocated or lost the password,
•
you can cancel the existing password by
the following procedure:
- Press VOLUME ▼ button of main unit.
- Keep pressing VOLUME ▼ button and press "0" key of
remote control simultaneously for a few seconds.
• May not work with Canadian programming or with U.S.
programming transmitted on cable networks in Canada.
• If you are changing channels using a cable box, while the TV/
VCR remains on channel 3 or 4, the V-Chip operates
differently. When you enter your password to temporarily
release the block on any channel, you have completely
disabled the V-Chip function for all stations. To reset the VChip turn your TV/VCR off and back on.
• Some cable boxes are built with a delay feature, in some cases
it can take up to 10 seconds for a program to appear after the
password has been input.
V-CHIP SET
CONFIRM
PASSWORD:
〈
0–9/ENTER/CANCEL/MENU
TO SET THE V-CHIP
1 In the V-CHIP SET menu, press
the SET/TRACKING + or –
button to select the TV RATING,
then press the ENTER button.
2 Press the SET/TRACKING + or
– button to display the desired
setting, then press the ENTER
button.
OFF : TV RATING is not set
TV-Y : All children
TV-Y7 : 7 years old and above
TV-G : General Audience
TV-PG : Parental guidance
TV-14 : 14 years old and above
TV-MA : 17 years old and above
• When you select TV- Y7, TV-PG, TV-14 or TV-MA,
press the CALL button to explain the rating. Press
the SET/TRACKING + or – button to select the
desired rating you want. Press the ENTER button
to select the setting ON or OFF.
3 Press the SET/TRACKING + or
– button to select the MOVIE
RATING, then press the ENTER
button.
4 Press the SET/TRACKING + or
– button to select desired rating,
then press the ENTER button.
OFF : MOVIE RATING is not set
G:All ages
PG : Parental guidance
〉
PG-13 : Parental guidance less than 13 years old
R:Under 17 years old Parental guidance
suggested
NC17 : 17 years old and above
X:Adult only
V-CHIP SET
V-CHIP : OFF
TV RATING : TV–PG
MOVIE RATING : PG–13
CHANGE PASSWORD
〈
+/–/ENTER/MENU
V-CHIP SET
V-CHIP : OFF
TV RATING : TV–PG
MOVIE RATING : PG–13
CHANGE PASSWORD
〈
+/–/ENTER/MENU
V-CHIP SET
V-CHIP : OFF
TV RATING : TV–PG
MOVIE RATING : PG–13
CHANGE PASSWORD
〈
+/–/ENTER/MENU
V-CHIP SET
V-CHIP : OFF
TV RATING : TV–PG
MOVIE RATING : PG–13
CHANGE PASSWORD
á
+/–/ENTER/MENU
〉
〉
〉
〉
ñ
5A30301A E P12-19 04/10/2001, 18:0116
TO SET THE ON TIMER
5 Press the SET/TRACKING + or
– button to select V-CHIP.
6 Press the ENTER button to
display ON.
7 Press the MENU button until the
MENU screen is cleared.
V-CHIP SET
V-CHIP : OFF
TV RATING : TV—PG
MOVIE RATING : PG—13
CHANGE PASSWORD
〈
+/—/ENTER/MENU
V-CHIP SET
V-CHIP : ON
TV RATING : TV–PG
MOVIE RATING : PG–13
CHANGE PASSWORD
〈
+/–/ENTER/MENU
〉
〉
NOTE : The V-Chip function is activated only on programs and tapes that have the rating signal.
To use the TV after the TV is protected.
When the program applied to the V-Chip setting is
received, enter the password, then press the ENTER
button. When the password is entered correctly the
protection will be temporarily overridden.
TO CHANGE PASSWORD
1 Press the MENU button.
2 Press the SET/TRACKING + or
– button to select the TV SET-UP,
then press the ENTER button.
3 Press the SET/TRACKING + or
– button to select the V-CHIP
SET, then press the ENTER
button.
4 Enter the Password using the
Direct Channel Selection
button (0-9), then press the
ENTER button.
5 Press the SET/TRACKING +
or – button to select CHANGE
PASSWORD, then press the
ENTER button.
6 Enter the new password using
the Direct Channel Selection
button (0-9), then press the
ENTER button.
7 Enter the same password
again to confirm, then press the
ENTER button.
8 Press the MENU button
repeatedly to return to normal
screen.
M E N U
TIMER REC SET
TV SET-UP
CH SET-UP
AUTO REPEAT ON OFF
SYSTEM SET-UP
〈
+/–/ENTER/MENU
〈
+/–/ENTER/MENU
V-CHIP SET
〈
0–9/ENTER/CANCEL/MENU
+
〈
〈
0–9/ENTER/CANCEL/MENU
〈
0–9/ENTER/CANCEL/MENU
〉
TV SET-UP
V-CHIP SET
ON/OFF TIMER
PICTURE
〉
PASSWORD: – – – –
V-CHIP SET
V-CHIP : ON
TV RATING : TV–PG
MOVIE RATING : PG–13
CHANGE PASSWORD
/–/ENTER/CANCEL/MENU
V-CHIP SET
V-CHIP : ON
TV RATING : TV–PG
MOVIE RATING : PG–13
CHANGE PASSWORD
NEW
PASSWORD: – – – –
V-CHIP SET
V-CHIP : ON
TV RATING : TV–PG
MOVIE RATING : PG–13
CHANGE PASSWORD
CONFIRM
PASSWORD: – – – –
This feature allows you to have the TV/VCR automatically turn “ON” at a predetermined time. If you
program the “ON” timer once, the TV/VCR will turn
“on” on the programmed day (daily/weekly) at the
same time to the same channel.
EXAMPLE: Turning on the TV to channel 12 at 7:00 AM,
MONDAY-FRIDAY.
1 Press the MENU button.
Press the SET/TRACKING + or
– button to select the TV SET-UP
option, then press the ENTER
button.
2 Press the SET/TRACKING + or
– button to select the ON/OFF
TIMER option, then press the
M E N U
TIMER REC SET
TV SET-UP
CH SET-UP
AUTO REPEAT ON OFF
SYSTEM SET-UP
〈
+/–/ENTER/MENU
TV SET-UP
V-CHIP SET
ON/OFF TIMER
PICTURE
ENTER button.
〈
+/–/ENTER/MENU
3 Press the SET/TRACKING + or
– button to select the ON TIMER
option, then press the ENTER
button.
4 Press the SET/TRACKING + or
– button to set the desired hour,
then press the ENTER button.
5 Set the desired minute, channel
and daily or weekly timer date
as in step 4.
6 Press the SET/TRACKING + or –
button to select the SET mode,
then press the ENTER button.
〉
Press the MENU button repeatedly to return to normal screen.
ON/OFF TIMER
ON TIMER
12:00AM CH001
MON-SAT CANCEL
OFF TIMER
12:00AM CANCEL
〈
+/–/ENTER/CANCEL/MENU
ON/OFF TIMER
ON TIMER
MON-SAT CANCEL
OFF TIMER
12:00AM CANCEL
〈
+/–/ENTER/CANCEL/MENU
ON/OFF TIMER
ON TIMER
MON-FRI CANCEL
OFF TIMER
12:00AM CANCEL
〈
+/–/ENTER/CANCEL/MENU
ON/OFF TIMER
ON TIMER
MON-FRI SET
OFF TIMER
12:00AM CANCEL
〈
+/–/ENTER/CANCEL/MENU
NOTES: • The TV/VCR will automatically turn off approxi-
〉
mately 1 hour later after the ON TIMER turns on
if no OFF TIMER has been set. To continue
watching the TV, press any button to cancel the
one hour automatic shut off.
• To cancel ON timer, follow above steps 1-5, then
press the SET/TRACKING + or – button to select
〉
the CANCEL. Press the MENU button repeatedly
to return to the normal screen.
• After setting the ON TIMER, "
will flash on and off. If you wish to set the OFF
" of the OFF TIMER
TIMER, press the ENTER button then follow the
steps 4-6 on " TO SET THE OFF TIMER" .
• If you want to correct the digits while setting,
〉
press the CANCEL button until the item you
want to correct, then press the SET/TRACKING
+ or – button to correct the desired setting.
ENGLISH
〉
〉
〉
7:00AM CH001
〉
7:00AM CH012
〉
7:00AM CH012
〉
17
5A30301A E P12-19 04/10/2001, 18:0117
Loading...