Memmert VO200, VO500, VO400 Operating Instructions

PERFECT
VO
set
off
on
push
card
PRINT
loop
t3
t4
t2
t1
on
off
Mo
Tu
We
Th
Fr
Sa Su
3
4
2
1
STERI DEFRO
°C
°C
rh
mb
%
CO mb
2
IN 1
IN 2
OUT
IN 1
IN 2
OUT
MIN
AUTO
MAX
VO
page 1
Vacuum Drying Oven VO200 / VO400 / VO500
Operating Instructions
Pump Module PM200 / PM400 / PM500
PERFECT page 2
1. Contents
1. Contents ......................................................................................................................................................................2
2. General notes and safety notes ....................................................................................................................................4
2.1 Material quality from MEMMERT: .......................................................................................................................4
2.2 Transport ...........................................................................................................................................................5
2.3 Initial start-up .................................................................................................................................................... 5
2.4 Oven load ..........................................................................................................................................................5
2.5 Safety check ......................................................................................................................................................5
3. Technical data ..............................................................................................................................................................6
3.1 Standard equipment of VO-ovens ......................................................................................................................7
3.2 Electrical equipment ..........................................................................................................................................8
3.3 External connection ........................................................................................................................................... 8
4. Installation facilities (accessories) ..................................................................................................................................9
4.1 Subframe ........................................................................................................................................................... 9
4.2 Stackable version ...............................................................................................................................................9
5. Oven construction and connections ............................................................................................................................10
6. Starting up ................................................................................................................................................................ 12
7. Switching output for external vacuum pump purge valve and pump control ...............................................................13
7.1 Vacuum pump purge valve ..............................................................................................................................13
7.2 Demand-controlled vacuum pump shut-down .................................................................................................13
8. Loading and Inertgas .................................................................................................................................................14
9. Guidelines for evaporating liquids in Memmert-vacuum ovens. ................................................................................... 15
10. Controls and indications .............................................................................................................................................16
11. Operating the door ....................................................................................................................................................16
12. Switching on .............................................................................................................................................................16
13. Setting the temperature .............................................................................................................................................16
14. Quick venting function ............................................................................................................................................... 17
15. Status indication for the heating levels .......................................................................................................................17
16. Selecting the operating mode .................................................................................................................................... 18
17. Setting the parameters ............................................................................................................................................... 18
18. Normal operation
............................................................................................................................................19
Setting example “Normal operation“ ..........................................................................................................................20
19. Weekly programmer ........................................................................................................................................21
Programming example “Weekly programmer“ ............................................................................................................22
20. Programme operation ...................................................................................................................................... 23
20.1 Closure commands for ramp segments ............................................................................................................25
Programming example programme operation ............................................................................................................26
21. Printer
PRINT
.............................................................................................................................................................29
22. Basic oven settings
SETUP
...........................................................................................................................................30
22.1 Real-time clock ................................................................................................................................................31
PERFECT page 3
23. Temperature monitor and protection devices ..............................................................................................................32
23.1 Mechanical temperature monitor: temperature limiter (TB) ...............................................................................32
23.2 Electronic temperature monitor ........................................................................................................................33
23.2.1 Overtemperature protection
MAX
................................................................................................................33
23.2.2 Undertemperature protection
MIN
..............................................................................................................33
23.2.3 Adjustable temperature monitor (TWW) Protection Class 3.1 to DIN 12 880 ................................................... 34
23.2.4 Adjustable temperature limiter (TWB) Protection Class 2 to DIN 12 880 .......................................................... 34
23.2.5 Automatic temperature monitor (ASF)
AUTO
.............................................................................................35
24. Calibration .................................................................................................................................................................38
24.1 Calibration-temperature ...................................................................................................................................38
24.2 Calibration-pressure (vacuum) ..........................................................................................................................40
25. Communication interface for the PC ...........................................................................................................................42
25.1 Communication interface RS232C .................................................................................................................... 42
25.2 Bus interface RS485 ......................................................................................................................................... 43
26. Report memory ..........................................................................................................................................................44
26.1 Reading the report memory .............................................................................................................................44
26.2 Reading the report memory into the PC via RS232C ..........................................................................................44
26.3 Printing the report memory from the oven .......................................................................................................44
27. Memory card: MEMoryCardXL ...................................................................................................................................45
27.1 Programming the MEMoryCardXL from the oven .............................................................................................45
27.2 Programming the MEMoryCardXL from a PC with the oven ..............................................................................45
27.3 Programming the MEMoryCardXL from a PC using the read-write unit .............................................................45
27.4 Documentation on memory card MEMoryCardXL .............................................................................................46
28. USER-IDcard (available as optional extra) .................................................................................................................... 47
29. Cleaning ....................................................................................................................................................................48
30. Maintenance .............................................................................................................................................................. 48
31. Door seal ...................................................................................................................................................................49
32. Error messages ...........................................................................................................................................................50
33. Supply failure .............................................................................................................................................................50
34. CE Conformity Declaration ......................................................................................................................................... 51
35. Address and customer service ....................................................................................................................................52
36. Index .........................................................................................................................................................................53
PERFECT page 4
This mark in the Operating Instructions means:
Watch out
Important Note!
2. General notes and safety notes
You have purchased a technically fully proven product which has been produced in Germany with the use of high-grade materials and the application of the latest manufacturing techniques; it has been factory tested for many hours. In addition we guarantee the supply of spare parts over 10 years.
This mark on the product means:
Note Operating Instructions
Warning – oven hot when operating!
Observation of the Operating Instructions is necessary for faultless
operation and for any possible claims under warranty. If these
Instructions are disregarded, all claims under warranty, guarantee and
indemnification are excluded!
The right to technical modifications is reserved. Dimensional details are not binding.
2.1 Material quality from MEMMERT:
External casing: stainless steel (V2A, Mat.Ref. 1.4301) Piping: stainless steel (V4A, Mat.Ref. 1.4571) Working space: stainless steel (V4A, Mat.Ref. 1.4404) featuring high stability, optimal hygienic
properties, and corrosion resistance against many (not all!) chemical compounds (warning against chlorine compounds, for example).
Thermotrays: stainless steel (Mat. Ref. 1.4404 = V4A). The heating mat is vulcanised to the
underside of the thermotray and covered with stainless steel; it consists of Silicone rubber.
Connector between thermotray and electrical socket in rear wall: Ryton R4 (GF PPS plastics)
and PEEK-GF30
Seals in solenoid valves and electrical sockets: fluoride rubber FKM/FPM (Viton) Door seal: Silicone rubber
The load for the vacuum drying oven must be carefully evaluated for its chemical compatibility with the above materials. A table listing about the compatibility of all these materials can be requested from MEMMERT.
PERFECT page 5
2.2 Transport
Always use gloves! If the oven has to be carried, at least 2 persons are required to transport it.
2.3 Initial start-up
When the oven is started up for the first time, it should be supervised continuously until steady conditions have been reached.
2.4 Oven load
Full consideration must be given to the physical and chemical properties of your load (e.g. combustion temperature etc.) in order to prevent serious damage to load, oven and surroundings. Please note that the Memmert ovens described here are not explosionproof (they do not conform to the Industrial Association Specification VBG 24) and are therefore not suitable for drying, evaporating and burning-in of paints, enamels or similar materials whose solvents may produce an inflammable mixture with air. There must be no possibility of the formation of inflammable gas/air mixtures either within the oven chamber or in the immediate surroundings of the equipment. Large amounts of dust or corrosive fumes inside the oven chamber or in the surroundings of the equipment may produce deposits within the oven and lead to short-circuits or damage the electronics. It is therefore important that adequate precautions are taken against excessive dust or corrosive fumes.
In order to ensure proper air circulation inside the chamber, there must be sufficient spacing of the load inside the oven. Do not place any load on the floor, against the side walls or underneath the ceiling of the chamber (heating ribs). In order to ensure optimum air circulation the shelves must be so inserted that the air spacings between door, shelf and rear chamber wall are approximately equal.
The maximum number and the loading of the shelves can be found in the table in the Section „Technical Data“.
2.5 Safety check
The door and the security glass panels must be checked regularly for scratches or damage. No vacuum must be applied to the oven if there is any damage.
PERFECT page 6
3. Technical data
Model 200 400 500 Chamber width A [mm] 385 385 545 Chamber height B [mm] 305 385 465 Chamber depth C [mm] 250 330 400 Oven width D [mm] 550 550 710 Oven height E [mm] 600 680 760 Oven depth F [mm] 400 480 550 Width G [mm] 529 529 689 Height H [mm] 450 290 130 Depth I [mm] 383 463 533 Chamber volume [litre] 29 49 101 Weight [kg] 58 82 120 Power [W] 1200 2000 2400 Max. number of shelves 3 4 4 Max. load per shelf [kg] 20 20 20 Max. load per oven [kg] 40 60 60 Ambient conditions Ambient temperature 5°C to 40°C
rH 80% max., no condensation Overvoltage category: II Contamination level: 2
Setpoint temperature range 20°C to 200°C
10mbar - 1100mbar Setting accuracy 0.5°C / 1mbar Working temperature range From 5°C above ambient temperature up to 200°C Leakage rate max. 0.5 x 10
-2
mbar 1/sec
PERFECT page 7
3.1 Standard equipment of VO-ovens
Electronic fuzzy-supported PID process controller with permanent power matching and time-saving
auto-diagnostic system for rapid fault finding (see Section: „Error messages“)
Language selection Alphanumerical text display Internal report memory 1024kB for storing actual temperature, setpoint temperature, pressure
and error states with time stamp
Control of oven and documentation of actual values on MEMoryCardXL Programme sequence control for up to 40 ramp segments Vacuum control for digital operation of the built-in solenoid valves Control output 24 Volt for purging and to switch off the external vacuum pump Selectable inlet valves for fresh air and inert gas Integral weekly programmer with group function (e.g. all workdays) Recessing push/turn control for simple operation of oven Visual alarm indication Built-in sounder as alarm on overlimit, as audible signal at programme end, and to acknowledge
input (key click)
Digital monitor controller for overtemperature, undertemperature, and as automatically setpoint-
following monitor (ASF)
Mechanical temperature limiter (TB Class 1) Monitor relay to switch off heating in case of fault Each thermotray has a separate Pt100 DIN Class A temperature sensor for temperature
measurement and can be removed individually
Convenient integral 3-point temperature calibration Temperature-dependent control panel venting Parallel printer interface (PCL3 compatible) Serial RS-232C interface for computer-supported temperature programmes and for reading the
internal report memory
MEMMERT software “Celsius 2005“ for remote operation of oven via a PC and for reading the
report memory inside the controller
A pre-formatted blank MEMoryCardXL with 32 kB storage capacity, reprogrammable for up to 40
ramp segments and additionally 270 hours report memory at 1 minute intervals
Special equipment (to be ordered separately as accessories): subframe, pump module, cable RS232C to DIN 12 900-1, external card reader for MEMoryCardXL for connection to the PC RS232C interface, 25-way printer cable (parallel, screened)
PERFECT page 8
Do not place the oven on a readily inflammable support surface!
WARNING! Always pull out the supply plug before
opening the oven cover!
3.2 Electrical equipment
Operating voltage see label 50/60 Hz
Current rating see label
Protection Class 1, i.e. operating isolation with ground connection to EN 61 010
Protection IP20 to EN 60 529
Interference suppression to EN55011 Class B
Oven protected by a fuse 250V/15A fast blow
Controller protected by a 100 mA fuse (200 mA on 115 V)
When connecting a MEMMERT oven to the electrical supply you have to observe any local regulations which apply (e.g. in Germany DIN VDE 0100 with FI protection circuit)
This product is intended to operate on a supply network with a system impedance Zmax at the transfer point (building connection) of 0.292 Ohm max. The user has to ensure that the product is only operated on an electrical supply network which meets these requirements. If necessary, details of the system impedance can be obtained from the local electricity supply authority.
Note: Any work involving opening up the oven must only be carried out by a suitably qualified electrician!
3.3 External connection Equipment connected to the external connections must have interfaces which meet the requirements for safe low voltage (e.g. PC, printer).
PERFECT page 9
4. Installation facilities (accessories)
The oven can be placed on the floor or on a bench (working surface). It is important that the oven is set up accurately horizontally; the door may have to be adjusted (see Section:
„Maintenance“)
The spacing from the back of the oven to the wall should be at least 15 cm. The spacing to the ceiling must not be less than 20 cm and that at the side to the wall not less than 8 cm. Generally it is essential to have adequate air ventilation around the oven.
Information on accessories will be found in our leaflet or on our internet page www.memmert.com. Please note the installation instructions for our accessories.
4.1 Subframe Oven models 200 to 500 can be mounted on a subframe (accessory)
4.2 Stackable version Two ovens of the same model size can be stacked on each other. Note that the oven with the lower working temperature must always be placed at the bottom. Foot locators (accessory) have to be fitted on the bottom oven.
Take off cover of bottom oven
Place drill jig (supplied with foot locators) into the inverted cover at the back
Mark holes and drill 4.2 mm dia.
Screw the foot locators to the top of the cover using the screws and nuts supplied
Re-fit the cover
15 cm min.
8 cm min.
8 cm min.
20 cm
min.
Oven on the
floor
Oven on
subframe
Oven on pump
module
Oven on pump
module and
subframe
PERFECT
6
3
4
2
7
1
5
10
8
9
12
11
page 10
5. Oven construction and connections
PERFECT
13
14
15
16
page 11
1 Computer connection, serial communication interface 2 Printer connection, parallel printer interface 3 Air/gas connection IN1 4 Air/gas connection IN2 5 Vacuum connection OUT 6 Norprene connecting tube vacuum pump to vacuum unit 7 Vacuum pump connection, pump module 8 Control connection for vacuum pump purge 9 Mains power connection pump module 10 Connecting line pump purge 11 Control connection pump purge 12 Mains power connection vacuum unit 13 Socket 14 Thermotray 15 Main switch pump module 16 Vacuum pump
PERFECT page 12
6. Starting up
1. Connect the vacuum connection (5) to the vacuum pump connection (6) of the pump module or to a suitable external vacuum pump, using the Neoprene connection tubing (7) supplied with the pump module.
2. When using a pump module, the connections for the pump purge (8+11) must be linked together using the cable (10) supplied with the equipment.
3. Plug in the mains supply plugs of the supply cables (9+12).
4. If the oven is to be charged with inert gas (e.g. nitrogen) the gas cylinder must be connected only to the gas inlet IN2 (4). The maximum pressure of 1.5 bar must not be exceeded! (Use pressure reducing valve for 1.5 bar max.)
5. Push in the thermotrays (14) as far as possible. Any thermotrays not being used should be placed on a soft surface.
6. Close the door of the vacuum oven.
7. Switch on the main switch (19) of the optional pump module.
8. Switch on the main switch (15) of the vacuum unit.
Warning
On first start-up do not operate
the oven unsupervised until
steady conditions have been reached!
PERFECT
2
3
1
page 13
7. Switching output for external vacuum pump purge valve and pump control
The 3-way switched output serves to control the vacuum pump of the optional pump module (PM) of the vacuum oven (VO).
7.1 Vacuum pump purge valve When loads with a high moisture content are being dried there is a possibility during prolonged operation that the pump output decreases through condensate forming in the pump heads. The diaphragms can be blown free by briefly purging the pump heads with fresh air. This improves the effectiveness of the drying process.
Note:
In conjunction with the optionally available pump modules PM 200, PM 400 and PM 500 this cyclic purge takes place automatically as the pump performance deteriorates.
Decisive advantage:
The drying process takes place more rapidly and with reduced energy consumption, the wear on the pump is reduced. This function can be de-activated by removing the pump purge connecting cable at the back of the unit.
7.2 Demand-controlled vacuum pump shut-down After the end of a drying programme, or after prolonged operation with any vacuum demanded by the controller, the vacuum pump incorporated in the pump module (PM) is switched off via the control line.
Note:
A control signal switches off the vacuum pump incorporated in the optional pump module (PM). The signal lamp in the main switch of the pump module remains alight even when the vacuum pump has been switched off via the control line.
Decisive advantage:
The demand-controlled shut down of the vacuum pump reduces energy consumption and increases the life of the vacuum pump by reducing the wear on the pump diaphragms. This function can be de-activated by removing the pump purge connecting cable at the back of the unit. The vacuum pump is then running continuously. unit.
Pin connections of the socket on the back of the unit:
1 output purge valve
(24V DC, 50 mA max.) 2 GND 3 pump switch-off
(24V DC, 50 mA max.)
PERFECT page 14
8. Loading and Inertgas
The load must only be placed on the thermotrays.
Slide in the thermotrays up to the stop.
Do not dry or heat any load which releases fumes developing an inflammable mixture in
combination with air.
Provide optimum heat transfer from the thermotray to the load. Ensure that the load rests properly
on the tray.
For maximum number of trays and load capacity of the thermotrays see the Table Technical data.
The table below gives recommendations for the appropriate loading of the trays which in turn is
essential for a largely uniform temperature distribution inside the oven.
Safety note:
When the oven is being operated with inert gas (nitrogen, helium, neon, argon, krypton) there is a small escape of the gas used into the environment. The list of MAK values (maximum workplace concentration) and of BAT values (biological workplace tolerance values) does not contain any information concerning the inert gases mentioned above. It is however still important to ensure good ventilation of the room. The appropriate specifications of the trade association publication „Guidelines for the Laboratory“ (ZH1/119) as well as DIN 1946 Part 7 „Room Air Technology (VDI Ventilation Rules)“ should be observed.
Precautions when handling gas cylinders:
Avoid any open fire in the area near the gas cylinders. Inert gas is not combustible, but it is
possible for the cylinder to burst.
Store cylinders below 50°C in a well ventilated location. Prevent ingress of water and any return
flow into the cylinder.
Connect up the gas cylinder only through a pressure reducing valve (1.5 bar max.).
When not in use, close the shut-off valve.
The instructions and safety information of the gas supplier have to be observed.
PERFECT page 15
9. Guidelines for evaporating liquids in Memmert-vacuum ovens.
Do not heat liquids in closed vessels.
In order to prevent condensation in the working space, heat liquids using a drying programme
(with venting cycles).
In order to prevent excessive condensation in the working space, working temperature and venting
cycles should be chosen to suit the moisture content of the load.
Do not heat any liquids releasing fumes which form an inflammable mixture with air.
During the evaporation of liquids with a large surface area it is possible that the cooling produced
during evaporation may result in the set temperature not being reached.
The oven described in these Operating Instructions
must never be used for drying or heating of loads
releasing fumes which may form an
inflammable mixture in combination with air!
The ovens described here must never be operated
in areas with a hazardous atmosphere!
PERFECT
set
off
on
push
card
PRINT
SETUP
loop
t3
t4
t2
t1
on
off
Mo
Tu
We
Th
Fr
Sa
Su
3
4
2
1
STERI DEFRO
°C
°C
rh
mb
%
CO mb
2
IN 1
IN 2
OUT
IN 1
IN 2
OUT
MIN
AUTO
MAX
page 16
10. Controls and indications
12. Switching on
The oven is switched on by pressing the push/turn control.
13. Setting the temperature
Hold down the SET key and set the temperature setpoint with the push/turn control. After the SET key has been released the display briefly flashes the temperature setpoint. The display then changes to the actual current temperature and the controller starts to control to the selected temperature setpoint.
open
close
11. Operating the door
The door is opened by pulling on the door handle. The door is closed by the door handle being pushed in.
Oven switched off. The push/turn control is pushed in and protected against damage.
Oven switched on and can be operated using the push/turn control and the SET key.
thermotrays
pressure displaytemperature
display
operating mode
indication
time
display
alarm indication
push/turn control
(main switch)
SET key chip card reader
monitor temperature
indication
text display
open
close
PERFECT
3
4
2
1
page 17
14. Quick venting function
The quick venting function is used in unloading and loading the vacuum oven without having to alter the selected vacuum setpoint:
1. Rotate control anticlockwise and select OPENDOOR in the menu.
2. For rapid venting of the vacuum oven, press SET key.
3. The vacuum oven is vented automatically to atmosphere so that the door can be opened.
4. To evacuate the vacuum oven to the most recently selected vacuum setpoint, press the SET key again.
15. Status indication for the heating levels
Heating tray symbol
lights up as soon
as a heating tray is
inserted
Heating symbol
lights up as soon
as this level is
heated
PERFECT page 18
16. Selecting the operating mode
PRINT
SETUP
After holding down the SET key (approx. 3 sec), the current operating mode flashes on the display. A different operating mode can be selected with the push/turn control while the SET key is being held down. After the SET key has been released the controller operates in the new operating mode.
17. Setting the parameters
After an operating mode has been selected, all relevant controller settings are shown simultaneously on the display. A parameter (menu item) can be selected by rotating the push/turn control; all other parameters are then dimmed. The selected parameter flashes brightly and can now be altered with the push/turn control while holding down the SET key. After the SET key has been released the newly set value is stored.
If the push/turn control or the SET key have not been operated for a period of 30 seconds, the controller automatically returns to the main menu.
Normal
operation
Weekly
programmer
Programme
operation
Printer Basic settings
PERFECT page 19
18. Normal operation
PRINT
SETUP
In this operating mode the oven operates continuously. The settings for operating the oven can be selected. The settings act directly on the operation of the oven.
3
4
2
1
STERI DEFRO
°C
°C
rh
mb
%
IN 1
IN 2
OUT
MIN
AUTO
MAX
By rotating the push/turn control the following parameters can be selected and can be altered as described in the Section „Setting the parameters“:
Temperature setpoint Range: 20°C to 200°C
˚C
Temperature monitor Adjustment range: MIN MAX AUTO
(see Section: “Temperature monitor“)
MIN
MAX
AUTO
°C
Pressure setpoint Range:
10mb to 1100mb LO = valve OUT permanently open
mB
PERFECT page 20
Setting example “Normal operation“ The oven (VO500) has to heat up to 180°C and be evacuated to 50 mbar.The monitoring function has to operate at 200°C.
Temperatur in ˚C
Druck in mb
Zeit
Zeit
180˚C
1. Select operating mode “Normal operation“
After holding down the SET key (approx. 3 sec), the current operating mode is flashing. Select operating mode I with the push/turn control while holding down the SET key. After the SET key has been released the controller is in operating mode I.
PRINT
SETUP
2. Select temperature setpoint
Hold down the SET key and use the push/turn control to select the required temperature setpoint of 180°C. After the SET key has been released the oven briefly flashes the temperature setpoint. The display then changes to the actual temperatureand the controller starts to control to the selected temperature setpoint 180°C. Heating is indicated by the orange heater symbol.
˚C
5. Select monitor temperature
Turn the push/turn control clockwise until the overtemperature display
MAX
is flashing. Hold down the SET key and use the push/turn control
to set the monitor temperature to 200°C.
MIN
AUTO
MAX
°C
4. Setting the vacuum
Rotate push/turn control clockwise until the vacuum indication is flashing. Hold down the SET key and use the push/turn control to set the required vacuum of 50mb. After releasing the SET key the oven briefly flashes the vacuum setpoint. The display then shows the actual pressure and the control starts to control to the selected vacuum of 50mb.
mB
PERFECT page 21
19. Weekly programmer
PRINT
SETUP
In this operating mode the weekly programmer is activated and the oven switches on and off automatically at the programmed times. While the weekly programmer is in the OFF phase the oven is in standby mode. Heating and fan are switched off, the controller display is dimmed and shows the clock time. The sequence of the weekly programmer is repeated every week. A maximum of 9 time blocks, each consisting of ON time and OFF time, can be programmed. Clockwise rotation of the push/turn control is used to select the temperature setpoint (etc.) to which the oven has to control during the ON phase. If no settings are made the controller takes the values from operating mode I.
Mo
Tu
We
Th
Fr
Sa
Su
h
on
off
By clockwise rotation of the push/turn control the parameters can be selected as in operating mode I, and altered as described in Section „Setting the parameters“. The time blocks are selected by rotating the push/turn control anticlockwise. The switching times can be altered while holding down the SET key.
Weekday Range: Monday to Sunday
Mo
Tu
We
Th
Fr
Sa
Su
Day groups Range: workday Mo-Fr
weekend Sa-Su
Mo
Tu
We
Th
Fr
Sa
Su
Mo
Tu
We
Th
Fr
Sa
Su
No ON time: ---­On these days the oven is not switched on
on
off
ON time Range: 00:00 to 23:59 hrs
on
off
h
OFF time Range: one minute above ON time to
24:00
on
off
h
For safety reasons, always check that an ON time has been programmed only during the required time blocks and days.
PERFECT page 22
Programming example “Weekly programmer“ The oven (UFP500) has to switch on at 07.30 hrs from Mo to Fr (workday group) and switch off at 18.00 hrs. In addition it has to operate on Saturday from 10.00 to 14.00 hrs.
Mo
Sa
Fr
Th
We
Tu
Su
1. Select operating mode “Weekly programmer“
After holding down the SET key (approx. 3 sec) the current operating mode is flashing. Select operating mode “Weekly programmer“ with the push/turn control while holding down the SET key. After the SET key has been released the controller is in operating mode “Weekly programmer“.
PRINT
SETUP
2. Switch on at 07.30 hrs Mo-Fr
Turn the push/turn control anticlockwise to select the symbols “Mo-Fr on“ (workday group). Hold down the SET key and use the push/turn control to set the switch­on time to 7:30.
Sa
Su
off
Mo
Tu
We
Th
Fr
h
on
3. Switch off at 18.00 hrs Mo-Fr
Using the push/turn control select the symbols “Mo-Fr off“ (workday group). Hold down the SET key and use the push/turn control to set the switch­off time to 18:00.
Sa
Su
on
Mo
Tu
We
Th
Fr
h
off
4. Switch on at 10.00 hrs Sa
Using the push/turn control select the symbols “Sa on“. Hold down the SET key and use the push/turn control to set the switch­on time to 10:00.
Mo
Tu
We
Th
Fr
Su
off
Sa
h
on
5. Switch off at 14.00 hrs Sa
Using the push/turn control select the symbols “Sa off“. Hold down the SET key and use the push/turn control to set the switch­off time to 14:00.
Mo
Tu
We
Th
Fr
Su
on
Sa
h
off
PERFECT page 23
20. Programme operation
PRINT
SETUP
In this operating mode, up to 40 freely programmable temperature-time ramps can be set. Rotating the press/turn control while holding down the SET key selects the following parameters in sequence after released the SET key:
- a new programme can be programmed or an existing programme can be edited
EDIT
- stops the programme
STOP
- starts the programme
START
After EDIT
has been activated, the following parameters can be selected and can be altered as
described in the Section “Selecting the parameters“:
PRINT
SETUP
loop
t3
t4
t2
t1
on
off
Mo
Tu
We
Th
Fr
Sa Su
°C
MAX
°C
h
Delayed programme start: switch-on day Range: Monday to Sunday, workdays Mo-Fr, weekend Sa-Sun, all days Mo-Su or no day. If no day of the week is selected, the oven starts up immediately after the programme is started. ( instant start )
PRINT
SETUP
loop
t3
t4
t2
t1
on
off
Mo
Tu
We
Th
Fr
Sa Su
°C
MAX
°C
h
Delayed programme start: switch-on time Range: 00:00 to 23:59 If no switch-on day has been selected it is not possible to select a switch-on time, and the programme starts immediately. ( instant start )
PERFECT page 24
PRINT
SETUP
loop
t3
t4
t2
t1
on
off
Mo
Tu
We
Th
Fr
Sa Su
MAX
°C
h
°C
rh
mb
%
IN 1
IN 2
OUT
Duration of first ramp segment Range: 1 minute to 999 hours
PRINT
SETUP
loop
t3
t4
t2
t1
on
off
Mo
Tu
We
Th
Fr
Sa Su
MAX
°C
h
°C
rh
mb
%
IN 1
IN 2
OUT
Setpoint temperature / temperature at the end of the ramp segment Range: 20°C to 200°C
PRINT
SETUP
loop
t3
t4
t2
t1
on
off
Mo
Tu
We
Th
Fr
Sa Su
MAX
°C
h
°C
rh
mb
%
IN 1
IN 2
OUT
Vacuum at the end of the ramp segment Adjustment range: 10 to 1100 mbar or LO
PRINT
SETUP
loop
t3
t4
t2
t1
on
off
Mo
Tu
We
Th
Fr
Sa Su
MAX
°C
h
°C
rh
mb
%
IN 1
IN 2
OUT
Closure command of ramp segment Range: next, spwt, loop, hold, end (see Section: „Closure commands for ramp segments“)
PRINT
SETUP
loop
t3
t4
t2
t1
on
off
Mo
Tu
We
Th
Fr
Sa Su
MAX
°C
h
°C
rh
mb
%
IN 1
IN 2
OUT
Exit the programme write mode EDIT Turn the push/turn control clockwise unti EXIT appears on the display, briefly press the SET key to enter
PERFECT page 25
20.1 Closure commands for ramp segments
NEXT Follow-on with next programme segment.
SPWT (T)
SET-POINT WAIT
Wait until the setpoint temperature is reached. The oven only starts the next programme segment when the programmed setpoint temperature has been reached, even if the programmed heating time has already elapsed.
SPWT (P)
SET-POINT WAIT
Wait until the set vacuum has been reached. The oven starts the next programme segment only when the programmed vacuum has been reached, even if the programmed segment time has already elapsed or if the set temperature has already been reached.
SPWT (PT)
SET-POINT WAIT
Wait until temperature setpoint and vacuum setpoint have been reached. The oven starts the next programme segment only when the programmed setpoint temperature and the programmed vacuum have been reached, even if the programmed segment time has already elapsed.
LOOP
Ramp repeat function. The set programme is repeated after passing through all programmed segments.
1-99 = repeats cont = continuous repeat function
HOLD
End of programme without switching off the heating; temperature and all other settings (e.g. air valve) are maintained.
END
Programmende mit Abschaltung der Heizung und Belüftung des Innenraums.
The programme segments are linked together by the segment closure command. These commands therefore control the programme sequence.
°C
Ramp
closure
command
ramp
segment 1
spwt (t)
t=time
segment 1
closure
command
ramp
segment 2
next
closure
command
ramp
segment 4
next
closure
command
ramp
segment 5
end
closure
command
ramp
segment 3
spwt (t)
segment 3
segment 1
segment 5
segment 4
delayed
programme start
PERFECT page 26
Programming example programme operation Das Gerät (VO500) soll am Montag um 8:00 Uhr auf 180°C heizen, und erst nach Erreichen der Temperatur auf 50mb evakuiert werden. Nach zweistündigem Halten von Druck und Temperatur soll innehalb von weiteren zwei Stunden der Druck auf 1050mB steigen und das Gerät auf 30°C abkühlen.
1. Select operating mode “programme“
After holding down the SET key (approx. 3 sec) the current operating mode is flashing. Hold down the SET key and select operating mode “programme“ using the push/turn control. After the SET key has been released the controller is in operating mode “programme operation“.
PRINT
SETUP
2. Edit programme
Hold down the SET key and turn the push/turn control to select ”EDIT”. After the SET key has been released, the controller is in the programme writing mode.
3. Weekday for delayed programme start
Hold down the SET key and turn the push/turn control to set the start day Mo.
Mo
4. Select clock time for delayed programme start
Using the push/turn control, select the time display. Hold down the SET key and set the time 08:00 using the push/turn control.
h
PERFECT page 27
5. Select duration of first ramp segment
Turn the push/turn control further clockwise until the time of the first ramp segment is flashing. Hold down the SET key and set the time 00:01 using the push/turn control.
h
6. Select temperature of first ramp segment
Turn the push/turn control clockwise until the temperature display is flashing. Hold down the SET key and set the required temperature setpoint of 180°C using the push/turn control.
˚C
7. Setting the vacuum of first ramp segment
Rotate push/turn control clockwise until the vacuum indication is flashing. Hold down the SET key and use the push/turn control to set the required vacuum of 1050mb.
mB
8. Set closure command of first ramp segment
Turn the push/turn control clockwise until a segment closure command (e.g. end ) appears. Hold down the SET key and set SPWT [T] with the push/turn control.
9. Select duration of second ramp segment
Using the push/turn control select the time indication. Hold down the SET key and set the time 00:01 using the push/turn control.
h
10. Select temperature of second ramp segment
Turn the push/turn control clockwise until the temperature display is flashing. Hold down the SET key and set the required temperature setpoint of 180°C using the push/turn control.
˚C
11. Setting the vacuum of second ramp segment
Rotate push/turn control clockwise until the vacuum indication is flashing. Hold down the SET key and use the push/turn control to set the required vacuum of 50mb.
mB
12. Set closure command for second ramp segment
Turn the push/turn control clockwise until a segment closure command (e.g end ) appears. Hold down the SET key and set SPWT (P) with the push/turn control.
13. Select duration of third ramp segment
Using the push/turn control select the time indication Hold down the SET key and set the time 02:00 using the push/turn control.
h
PERFECT page 28
14. Select temperature of third ramp segment
Turn the push/turn control clockwise until the temperature display is flashing. Hold down the SET key and set the required temperature setpoint of 180°C using the push/turn control.
˚C
15. Setting the vacuum of third ramp segment
Rotate push/turn control clockwise until the vacuum indication is flashing. Hold down the SET key and use the push/turn control to set the required vacuum of 50mb.
mB
16. Set closure command for third ramp segment
Turn the push/turn control clockwise until a segment closure command (e.g end ) appears. Hold down the SET key and set NEXT with the push/turn control.
17. Select duration of fourth ramp segment
Using the push/turn control select the time indication Hold down the SET key and set the time 02:00 using the push/turn control.
h
18. Select temperature of fourth ramp segment
Turn the push/turn control clockwise until the temperature display is flashing. Hold down the SET key and set the required temperature setpoint of 30°C using the push/turn control.
˚C
19. Setting the vacuum of fourth ramp segment
Rotate push/turn control clockwise until the vacuum indication is flashing. Hold down the SET key and use the push/turn control to set the required vacuum of 1050mb.
mB
20. Set closure command for fourth ramp segment
Turn the push/turn control clockwise until a segment closure command (e.g end ) appears. Hold down the SET key and set END with the push/turn control.
21. Exit programme writing mode EDIT
Turn the push/turn control clockwise until EXIT appears on the display. Press the SET key briefly to enter.
22. Set temperature monitor
Turn the push/turn control clockwise and set the temperature monitor.
(see Section: “Temperature monitor”)
MIN
MAX
AUTO
°C
23. Start programme
Turn the push/turn control anticlockwise until the stop symbol is flashing. Hold down the SET key and select Start with the push/turn control.
PERFECT page 29
21. Printer
PRINT
PRINT
SETUP
All VO-ovens are fitted as standard with a parallel printer interface, as used on personal computers.
This parallel printer interface on the back of the oven is suitable for connecting conventional PCL3­compatible ink jet and laser printers which are provided with a parallel printer interface (e.g. HP Deskjet 5550 or HP Deskjet 9xx).
It is important to use a screened interface cable. The screen must be connected to the plug case.
The controller is provided with an internal report memory (see Section: „Report memory”). The report data can in this operating mode be printed out through the printer connected to the oven.
When using a colour printer, the various graphics can be printed in colour.
On the printout the GLP data head is also printed automatically and contains the following information:
- Printing date
- Time period of report
- Running page number
- Serial number and oven designation
By turning the push/turn control the following parameters can be selected in turn and altered as described in the Section Setting the parameters.
Reading the date of the first print page
FIRST PAGE
Reading the date of the last print page
LAST PAGE
Start graphics print
PRINT
Print programme and configuration page
LIST
Exit print menu and back to main menu
EXIT
PERFECT page 30
22. Basic oven settings
SETUP
PRINT
SETUP
In this operating mode it is possible to make the basic settings of the oven. Clock time, date, day, year, and settings of sounder, of address assignment, monitoring units, heater power and calibration are set here.
The following parameters can be selected by turning the push/turn control, and altered as described in the
Section „Setting the parameters“:
Clock time in 24-hour format The winter/summer time changeover does not take place automatically but must be set manually by the user.
h
Date The controller incorporates a calendar which automatically allows for the different lengths of the months and also for leap years.
Weekday
Mo
Year Range: from 2000 to 2100
Audible signal at programme end Setting: OFF or ON
Audible signal on alarm, e.g. overtemperature Setting: OFF or ON
Communication address Range: 0 to 15
(see Section: „Communication interface”)
Tolerance margin ASF Range: 2 to 20 °C
(see Section: „Temperature monitor”)
PERFECT page 31
Temperature monitor function Adjustable temperature monitor (TWW) Protection Class 3.1 to DIN 12 880
Adjustable temperature limiter (TWB) Protection Class 2 to DIN 12 880
(see Section: „Temperature monitor”)
Language Settings: GERMAN, English, franCEAIS, ESPANOL and italIANO
Vent connection select IN1 or IN2
Settings: IN1 or IN2 e.g. IN1 for fresh air and IN2 for inert gas
Calibration correction for user-calibration of temperature. CAL1 to CAL3
Adjust - oven-temperature for adjustment RE-Adjusting temperature value
(see Section: „Calibration“)
Calibration correction for user-calibration of vacuum. CAL1 to CAL3
Adjust - oven-temperature for adjustment RE-Adjusting temperature value
(see Section: „Calibration“)
Exit setup mode = store all settings and exit setup mode.
22.1 Real-time clock
The real-time clock is set in SETUP and includes date and clock time. The real-time clock serves for documentation according to GLP. Date and clock time are marked in the report print. On the graphics print the time axis is marked in real-time. The clock runs with a buffer battery independently of the mains power supply. The built-in lithium battery Type CR 2032 has a life of approx. 10 years.
PERFECT page 32
23. Temperature monitor and protection devices
Die Überwachungstemperatur wird über die PT100-Tempratursensoren in den Heizblechen gemessen. Die Überwachungseinheit dient zum Schutz des Beschickungsgutes und als Geräte- und Umgebungsschutz.
The oven is provided with duplicate overtemperature protection (mechanical / electronic) according to DIN 12 880.
MIN
MAX
AUTO
°C
23.1 Mechanical temperature monitor: temperature limiter (TB)
All ovens of the PERFECT series are equipped with a mechanical temperature limiter (TB) Protection Class1 to DIN 12 880. If the electronic monitor system should fail during operation and the fixed factory-set maximum temperature is exceeded by approx. 20°C the temperature limiter switches off the heating permanently as a final protective measure. The alarm symbol lights up as warning
Fault rectification after the TB cut-out has been activated:
Switch off the oven and allow it to cool down Rectify the fault (e.g. replace temperature probe) and where appropriate contact customer service The oven is again ready for operation only after it has cooled down and after the fault has been
rectified
1.
2.
3.
Overtemperature
protection
(TWW, TWB)
Undertemperature protection
Audible
alarm signal
Automatic
temperature monitor
(ASF)
visual alarm symbol alight: TB alarm flashing: TWW alarm TWB-alarm ASF-alarm
PERFECT page 33
23.2 Electronic temperature monitor
23.2.1 Overtemperature protection
MAX
Range: up to 10°C max above nominal temperature (for nominal temperature see label)
MIN
MAX
AUTO
°C
Using the push/turn control select the symbol
MAX
­Symbol anwählen. Hold down the SET key and set the protection temperature using the push/turn control.
23.2.2 Undertemperature protection
MIN
Range: from 10°C below minimum temperature of oven to 10°C above nominal temperature of oven (for nominal temperature see label).
The low alarm cannot be programmed above the value set as high alarm.
Where no undertemperature protection is required, this has to be set to the lowest temperature.
MIN
MAX
AUTO
°C
Using the push/turn control select the symbol
MIN
. Hold down the SET key and set the protection temperature using the push/turn control.
Note:
The temperature monitor can be set independently of the operating mode. During ramp operation the monitor temperature must always be set sufficiently far above the maximum working temperature.
PERFECT page 34
The manually set monitor temperature and the electronic overtemperature protection are monitored on VO-ovens by an adjustable temperature monitor (TWW) Protection Class 3.1 to DIN 12 880, or by an adjustable temperature limiter (TWB) Protection Class 2 to DIN 12 880. The choice of temperature monitor is selected in SETUP (see the menu item Tolerance margin ASF in Section “Basic oven settings”)
23.2.3 Adjustable temperature monitor (TWW) Protection Class 3.1 to DIN 12 880 If the manually set monitor temperatur
MAX
is exceeded, the TWW takes over the control of the temperature
and starts to control at the monitor temperature. As a warning the alarm symbol is flashing.
TB approx. 20°C above Tmax
TWW set manually setpoint temperature
220°C
150°C
20°C
t
°C
controller fault
emergency operation
23.2.4 Adjustable temperature limiter (TWB) Protection Class 2 to DIN 12 880 If the manually set monitor temperature
MAX
is exceeded, the TWB switches off the heating permanently
and can only be reset by pressing the SET key. As a warning the alarm signal is flashing.
TB approx. 20°C above Tmax
TWB set manually setpoint temperature
220°C
150°C
20°C
t
°C
controller fault
heating switched off by TWB
PERFECT page 35
23.2.5 Automatic temperature monitor (ASF)
AUTO
A monitoring device which automatically follows the selected temperature setpoint. The tolerance margin of the ASF is set in SETUP (see the menu item Tolerance margin ASF in the Section
„Basic oven settings SETUP“).
Automatic temperature monitor OFF
(ASF OFF)
MIN
MAX
AUTO
°C
Using the push/turn control select the AUTO symbol. Hold down the SET key and select off using the push/turn control.
Automatic temperature monitor ON
(ASF ON)
MIN
MAX
AUTO
°C
Using the push/turn control select the AUTO symbol. Hold down the SET key and select on using the push/turn control.
Notes on the ASF:
The tolerance margin for the ASF is selected in SETUP (see the menu item Tolerance margin ASF in the
Section „Basic oven settings SETUP”).
Tolerance margin reached = ASF activated
The ASF is automatically activated when the actual temperature has reached 50% of the selected tolerance margin of the setpoint (in the example 150°C – 5°C). The activation of the automatic temperature monitor is indicated by the bright
AUTO
-symbol.
160°C
140°C
ASF alarm
ASF activated
ASF activated
A
ASF set to
+/-10°C in
SETUP
PERFECT page 36
Going outside tolerance margin = ASF alarm
Going outside the selected tolerance margin of the setpoint (in the example 150°C +/-10°C), for example through opening the oven door during operation, triggers the alarm. Triggering the ASF alarm is indicated by flashing
AUTO
and -symbol.
If the sounder is switched on in SETUP, the ASF alarm is additionally signalled by an interrupted tone. By pressing the SET key the sounder can be switched off temporarily until the next occurrence of an alarm event.
160°C
140°C
ASF alarm
ASF activated
ASF activated
16
0
14
0
ASF-alarm
Again within tolerance margin = ASF alarm switched off
The automatic temperature monitor alarm is switched off automatically as soon as the selected tolerance margin of the setpoint (in the example 150°C +/-100°C) is reached again.
160°C
140°C
ASF alarm
ASF activated
ASF activated
160°C
140°C
ASF-alarm
ASF activated
ASF set to
+/-10°C in
SETUP
ASF set to
+/-10°C in
SETUP
PERFECT page 37
Setpoint changed = ASF de-activated automatically
If the temperature setpoint is altered, the automatic temperature monitor is automatically de-activated temporarily (see in the example the setpoint is changed from 150°C to 75°C) until the tolerance margin of the new temperature setpoint is reached (see in the example below: the ASF is re-activated at 75°C +/­10°C).
160°C
140°C
ASF alarm
ASF activated
ASF activated
160°C
140°C
ASF-alarm
ASF activated ASF activated
85°C
65°C
ASF set to
+/-10°C in
SETUP
PERFECT page 38
24. Calibration
24.1 Calibration-temperature
User-calibration of oven and controller, with three calibration temperatures selected by the user.
CAL1 temperature calibration at low temperature CAL2 temperature calibration at medium temperature CAL3 temperature calibration at high temperature
Either a positive or a negative calibration correction can be applied to each selected calibration point.
General calibration instructions:
1. Select the required calibration temperature in SETUP and set the corresponding calibration correction to 0.0°C.
2. Measure the deviation from the selected calibration temperature under steady conditions, using a reference instrument.
3. Set the calibration correction in SETUP. If the measured reference temperature is too low, the calibration correction setting has to have a negative sign.
4. Carry out a check measurement using the reference meter.
5. The procedure can be carried out for up to 3 calibration temperatures.
Example: Correction of a temperature deviation in the load at 100°C.
1. Set calibration temperature CAL.2 to 100.0°C in SETUP and set the corresponding calibration correction to 0.0°C.
2. Using a calibrated reference instrument, an actual temperature of 99.6°C is measured in normal operation for a setpoint temperature of 100°C.
3. In SETUP set the calibration correction for CAL.2 to –0.4°C.
4. After the oven has settled down the reference instrument should read 100.0°C.
5. With CAL.1 a further calibration temperature can be programmed below CAL.2 , and with CAL.3 an additional calibration temperature above CAL.2.
CAL 1
+0,5°C
CAL 3
+0,8°C
CAL 2
-0,4°C
factory
calibration
180°C
100°C
0°C
40°C
PERFECT
h
˚C
˚C
h
˚C
˚C
h
˚C
˚C
page 39
Note: If all calibration corrections are set to 0.0°C the factory calibration is restored.
Calibration correction
Range –9.9°C to +9.9°C
Calibration temperature
Range down to 10°C below
CAL2
Calibration point 1
Calibration correction
Range –9.9°C to +9.9°C
Calibration temperature
Range 10°C above CAL1 to
10°C below CAL3
Calibration point 2
Calibration correction
Range –9.9°C to +9.9°C
Calibration temperature Range
10°C above CAL2 up to nominal
temperature
Calibration point 3
PERFECT page 40
24.2 Calibration-pressure (vacuum)
User-calibration of the oven on the controller at three user-selected vacuum values:
CAL1 pressure calibration at low vacuum pressure CAL2 pressure calibration at medium vacuum pressure CAL3 pressure calibration at high vacuum pressure
A positive or a negative calibration correction can be applied to each selected calibration point.
General calibration instructions:
Select the required calibration vacuum in SETUP and set the corresponding calibration correction
to 0mb.
Using a standard vacuum gauge, measure the deviation at the selected calibration vacuum under
steady conditions.
Set the calibration correction in SETUP. If the measured vacuum pressure is too low, the calibration
correction has to be set with a negative sign.
Carry out a check measurement with the reference gauge. The procedure can be performed for up to 3 calibration vacuum pressures.
Example: to correct the vacuum deviation in the load at 500 mbar.
1. Set calibration vacuum CAL2 in SETUP to 500mb and set the corresponding calibration correction to 0mb.
2. In normal operation and at the vacuum setting of 497 mbar, an actual vacuum pressure of 503 mbar is measured using a reference gauge.
3. Set calibration correction CAL2 in SETUP to –3mb.
4. After the oven has stabilised, the reference gauge should indicated 500 mbar.
5. A further vacuum calibration below CAL2 can be programmed with CAL1, and another one above CAL2 with CAL3.
1.
2.
3.
4.
5.
PERFECT
h
mB
mB
h
mb
mB
h
mB
mB
page 41
Note: When all the calibration corrections are set to 0mb, the oven is restored to the factory calibration
Calibration correction
Range –10mB to +10mb
Vacuum calibration
adjustment range: down to
10 mbar below CAL2
Calibration point 1
Calibration correction
Range –10mB to +10mb
Vacuum calibration
adjustment range: 10 mbar
above CAL1 to 10 mbar
below CAL3
Calibration point 2
Calibration correction
Range –10mB to +10mb
Vacuum calibration adjustment range: 10 mbar above CAL2 up
to 1100 mbar
Calibration point 3
PERFECT page 42
25. Communication interface for the PC
25.1 Communication interface RS232C
The oven is provided as standard with a serial communication interface RS232C according to DIN 12 9001. Using this interface it is possible to control the oven from the PC and to produce reports. This is done using the “Celsius 2005“ software. For this purpose the oven has to be assigned a unique device address in sub-menu SETUP, option ADDRESS; This is the address through which the PC communicates with the oven. The default setting is ADDRESS 0. Using this address each oven can be addressed by the PC and programmed. If several ovens are connected by the RS232C interface to one PC, each oven requires a corresponding interface on the PC as well as a separate cable. The maximum cable length is 15 m. For connection of the oven to the PC there is a 9-pin connector on the back of the oven. The oven can be connected to the PC using a screened interface cable. The screen has to be connected to the plug case. If the serial interface is not being used, the cover supplied has to be fitted !
RS 232-C
9-pin serial
12345
6987
1234 5 678 9
not used RXD TXD not used GND not used not used not used not used
PERFECT
RS485
RS232
page 43
25.2 Bus interface RS485
When so ordered, the oven can be equipped at the factory with an RS485 interface instead of the RS232C interface. This permits networking of several ovens (up to 16) with a single PC using a common 2-wire circuit. The system is operated using the “Celsius 2005” software. A unique device address has to be assigned to the oven in sub-menu SETUP, option ADDRESS. This is the address through which the PC communicates with the oven. The default setting is ADDRess 0. Using this address each oven can be addressed by the PC and programmed.
For this purpose the PC must be equipped with an RS485 interface or must be fitted with an RS232/RS485 converter. The cabling has to suit the individual location using a screened cable. The maximum total length of the cable is 150 m. A maximum of 16 devices can be addressed on the RS485 bus. A termination resistance of 220 Ohm has to be connected to the last device.
RS 485
9-pin serial
12345
6987
1234 5 678 9
not used not used A not used not used not used not used B not used
Converter
PERFECT page 44
26. Report memory
The controller continuously records all relevant measurements, settings and error messages at 1-minute intervals.
The internal report memory is arranged as a ring memory, i.e. the new data always overwrite the oldest report data.
The report function can not be switched off but remains active at all times. The data are stored in the controller, protected against any manipulation. The controller memory can be read to produce documentation.
Every data set is stored with a unique date stamp.
The size of the internal report memory is 1024kB. This corresponds to a memory capacity of approximately 6 months‘ continuous operation.
During ramp operation a larger amount of data are stored in the memory so that the maximum report duration may be reduced.
If the power supply is interrupted, the instants of power failure and restoration of power are stored in the controller.
26.1 Reading the report memory
Past report data can be printed either via the RS232C interface or by a PLC3-compatible printer connected to the oven.
26.2 Reading the report memory into the PC via RS232C
Using the “Celsius 2005“ program the record memory of the controller can be read via the RS232C interface into a PC where it can be shown graphically, printed, and stored in memory.
Note:
The report memory of the controller is not altered or cleared by the reading procedure.
26.3 Printing the report memory from the oven
(see Section: „Printer“)
If the printer is not ready, e.g. cartridge empty or no paper, no report data are lost. Prints can be repeated several times since the report memory is not cleared after printing.
The GLP data header is automatically included in the print-out: it contains the following information:
- Printing date
- Time period of report
- Running page number
- Serial number and oven designation
PERFECT page 45
27. Memory card: MEMoryCardXL
A temperature programme with up to 40 ramps can be programmed on the MEMoryCardXL. Programming can take place directly on the controller or through the PC program “Celsius 2005”. For improved clarity it is recommended that extensive programmes are prepared graphically on the PC. Where a MEMoryCardXL is programmed, it can be read only on the same oven type for which it has been programmed. Marking: The text field of the MEMoryCardXL can be marked individually with text or diagram
27.1 Programming the MEMoryCardXL from the oven Insert the MEMoryCardXL into the slot in the control panel field. The selected settings are written directly to the card and stored on it. After the card has been removed, the programme stored internally in the controller becomes again activated.
27.2 Programming the MEMoryCardXL from a PC with the oven Link the PC to the oven with an interface cable via the serial interface (see Section: „Communication
interface“). Insert the MEMoryCardXL into the input slot in the control panel field.
Write protection: The Memory Card XL can be provided with write protection using the PC program “Celsius 2005”. The programme on the card can then not be altered on the controller.
27.3 Programming the MEMoryCardXL from a PC using the read-write unit Using a read-write unit (which can be purchased separately) the MEMoryCardXL can be programmed from a PC with “Celsius 2005” without any connection to an oven. It is important to ensure that the MEMoryCardXL has to be inserted with the contact field pointing upwards towards the marking of the read-write unit.
PERFECT page 46
Note:
The programme remains stored on the Memory Card XL after the card has been removed from the unit. It can however be overwritten at any time by the PC using “Celsius 2005”.
Details on programming the MEMoryCardXL with PC and Celsius 2005 can be found in the Celsius Operating Manual and in the Online Help.
27.4 Documentation on memory card MEMoryCardXL
The actual temperatures can be documented continuously on the memory card while the programme is running from the chip card. After the programme has been completed they can be read and printed using “Celsius 2005”. The operation is described in the “Celsius 2005” Operating Manual.
A certain amount of storage space is provided for documentation depending on the programme duration. The sampling rate is set automatically by the controller depending on the programme duration. With a programme duration up to 270 hours the documentation of the actual values on the MEMoryCardXL takes place with a 1-minute cycle. With programmes of longer duration the sampling time is extended up to 30 min max.
Documentation is started afresh on each programme start; the old report data are overwritten.
PERFECT page 47
28. USER-IDcard (available as optional extra)
The USER-IDcard stores the serial number of the oven and a unique user number in encrypted format. The USER-IDcard therefore functions only in the oven with the corresponding serial number.
Each log-on via the USER-IDcard is documented in the internal flash memory.
If the USER-IDcard is inserted, the SETUP menu includes the additional item ID-LOCK. When the setting is changed to ON, all changes to the oven are blocked after the chip card has been removed.
The blockage through the USER-IDcard is indicated by the illuminated key symbol
on the control
panel.
Important:
If the oven is blocked through the USER-IDcard, there is no
programme operation with the MEMoryCardXL since that card could
be removed at any time and reprogrammed externally.
PERFECT
1
2
3
4
6
5
page 48
29. Cleaning
Regular cleaning of the easy-to-clean inside of the chamber prevents deposits which over time can detract from the appearance and the functionality of the stainless steel chamber .
The metal surfaces of the oven can be cleaned with commercially available cleaning agents for stainless steel. It is important to ensure that no rust-forming object comes into contact with the chamber or the stainless steel casing. Rust deposits cause infection of the stainless steel.
If any contamination causes rust stains on the surfaces of the chamber, such spots must be cleaned off immediately and the area polished.
The control panel, the plastic input modules and other plastic components of the oven must not be cleaned using scouring cleaning agents or those containing solvents.
30. Maintenance
Important for a long life of your MEMMERT product and in case of warranty claims.
Note: Any work involving opening up the oven must only be carried out by a suitably qualified electrician!
MEMMERT products require little maintenance. It is however recommended to lubricate all moving parts of the doors (hinges and closure) once a year (or 4 times a year with continuous operation) using a thin Silicone grease, and to check that the hinge screws are tight.
A well-closing door is essential on an oven. On Memmert ovens, tight closure of the door is ensured by a seal on the oven and another one on the door. In continuous operation the flexible sealing material may take a permanent set. Readjustment may then be necessary in order to ensure proper closing of the door.
The top part (1) of the door hinge can, after releasing the 2 screws (2) at the top or bottom of the door, be moved slightly in the direction of the arrow.
The door can be adjusted after releasing the socket screw (3) and rotating the excentric (4) by means of a screwdriver. NOTE ! Screw (3) is locked with locking varnish. It can be released by a sharp tug using a hexagon socket key. Apply more locking varnish to screw (3) and tighten it.
The closing panel (6) can also be adjusted in the direction of the arrow after releasing the screw (5). It is important that the panel is then screwed down firmly.
PERFECT page 49
31. Door seal
The areas indicated should always be dusted with talcum powder.
Talcum powder
Talcum
powder
PERFECT page 50
32. Error messages
Fehlerart Ursache Fehlerbeseitigung Hauptschalter eingeschaltet,
Display bleibt dunkel
Stromversorgung kontrollieren, Geräteschutzsicherung defekt
Stromversorgung kontrollieren. Sicherung von Elektrofachkraft überprüfen lassen. Sicherung
Anzeige „----„ in Temperatur-Anzeige
Heizblech PT100-Sensor defekt oder nicht richtig eingeschoben
Thermoblech vollständig einschieben. Evtl. in einer anderen Heizebene prüfen
Thermoblech erwärmt sich nicht, obwohl gelbe Heizungs-LED leuchtet
Interne Temperatursicherung des Thermoblechs defekt
Thermoblech zur Überprüfung an den Kundendienst senden
Rotes Alarm-Symbol leuchtet dauernd Temperaturbegrenzer
angesprochen
Siehe Kapitel: „Mechanische Temperaturüberwachung: Temperaturbegrenzer ( TB)“
Anzeige „E-1.1“ Anzeige „E-2.1“ Leistungsteil Heizebene 1 defekt Kundendienst
Anzeige „E-1.2“ Anzeige „E-2.2“ Leistungsteil Heizebene 2 defekt Kundendienst Anzeige „E-1.3“ Anzeige „E-2.3“ Leistungsteil Heizebene 3 defekt Kundendienst Anzeige „E-1.4“ Anzeige „E-2.4“ Leistungsteil Heizebene 4 defekt Kundendienst Fehlermeldung „E-3“ in Druck-Anzeige Drucksensor defekt Kundendienst
As far as VO appliances are concerned, error messages are shown in the alphanumeric display. In case there is a fault on the oven, please get in touch with an authorised service organisation or contact the Memmert customer service department. When dealing with the service department always quote the product serial number on the oven label.
33. Supply failure
Supply failure in operating mode “Normal operation“
After a supply failure the operation is continued with the set parameters. The instant and duration of the supply failure are documented in the record memory.
Supply failure in operating mode “Weekly programmer“
After a supply failure the operation is continued with the set parameters. The instant and duration of the supply failure are documented in the record memory.
Supply failure in programme operation
After a supply failure lasting less than 15 minutes the current programme is continued at the point where it was interrupted. The instant and duration of the supply failure are documented in the report memory.
On a supply failure lasting longer than 15 minutes the oven immediately starts in manual operation for safety reasons and all settings are set to safe default values (see table).
Supply failure in remote operation
On a supply failure in remote operation the oven immediately starts in manual operation for safety reasons and all settings are set to safe default values (see table). Programme continuation has to take place from the PC. The instant and duration of the supply failure are documented in the report memory.
Parameter Default-value Temperature 20 °C Pressure 1100mB
PERFECT page 51
D09950 / 24.02.05
EC Declaration of Conformity
Manufacturer´s name and address: MEMMERT GmbH + Co. KG
Äußere Rittersbacher Straße 38
D-91126 Schwabach Product: Vacuum-drying-oven Type: VO … Sizes: 200 / 400 / 500 Nominal voltage: AC 230 V 50 / 60Hz
The designated product is in conformity with the European EMC-Directive
89/336/EEC
including amendments
Council Directive of 03 May 1989 on the approximation of the laws of the Member States relating to
electromagnetic compatibility.
Full compliance with the standards listed below proves the conformity of the designated product with the essential protection requirements of the above-mentioned EC Directive:
DIN EN 61 326 (VDE 0843 part 20): 1998-01 EN 61 326: 1997 DIN EN 61 326/A1 (VDE 0843 part 20/A1): 1999-05 EN 61 326: 1997/A1 : 1998 RFI suppression: Class B DIN EN 61 000-3-11 (VDE 0838 part 11): 2001-04 EN 61 000-3-11: 2000
The designated product is in conformity with the European Low Voltage Directive
73/23/EEC
including amendments
Council Directive on the approximation of the laws of the Member States relating to Electrical
equipment for use within certain voltage limits.
Full compliance with the standards listed below proves the conformity of the designated product with the essential protection requirements of the above-mentioned EC Directive:
DIN EN 61 010-1 (VDE 0411 part 1): 1994-03 EN 61 010-1: 1993 DIN EN 61 010-2-010 (VDE 0411 part 2-010): 1995-03 EN 61 010-2-010: 1994
Schwabach, 24.02.05
(Legally binding signature of the issuer)
This declaration certifies compliance with the above mentioned directives but does not include a property assurance. The safety note given in the product documentation which are part of the supply, must be observed.
34. CE Conformity Declaration
PERFECT page 52
Standard ovens (VO) are safety-approved and bear the test marks:
35. Address and customer service
MEMMERT GmbH+Co.KG PO Box 17 20 91107 Schwabach Germany Phone: (+49) (0)9122 / 925-0 Fax:: (+49) (0)9122 /14585 E-mail: sales@memmert.com Internet: www.memmert.com
Customer service: Phone: (+49) (0)9122 / 925-143 or (+49) (0)9122 / 925-126 E-mail: service@memmert.com
When contacting customer service, always quote the product serial number on the oven label.
PERFECT page 53
36. Index
A
accessories 9 address 53 air supply 10 air valve 13 air valve indication 11 alarm indication 11 alarm symbol 26, 28 ASF 29 automatic temperature monitor 29
B
BALANCE 36 basic oven settings 24 bus interface 35
C
calibration 32 calibration correction 32 calibration temperature 32 CE conformity declaration 50 cleaning 48 closure commands 19 connection 8 construction, oven 10 controls 11 customer service 53
D
day groups 15 delayed programme start 17 DIN 12 880 26 door 10 door handle 10
E
END 19 error messages 49
F
fan 10 fan indication 11 fan speed 13
H
heating power distribution 36 HOLD 19
I
indications 11 initial start-up 5 installation facilities 9
L
load, oven 5 LOOP 19
M
maintenance 48 material quality 4, 7 medical product 4 memory card 38 MEMoryCardXL 38
N
NEXT 19 normal operation 13
O
OFF time 15 ON time 15 operating mode, selection of 12 operating mode indication 11 operation 10 oven settings, basic 24 overtemperature protection 27
P
parameters, setting the 12 printer 23 programme segments 19 Protection Class 1 26 Protection Class 2 28 Protection Class 3.1 28 protection devices 26 purpose, intended 4, 42
R
ramp segments 19 RS232C 34 RS485 35
S
setpoint-dependent waiting time 17 SETPOINT WAIT 19 SPWT(T) 19 stacking 9
start-up 5 Steri card 40 steriliser cassettes 47 sterilisers 42 subframe 9
T
TB 26 temperature, setting the 11 temperature calibration 32 temperature deviation 32 temperature display 11 temperature limiter 26 temperature monitor 26 temperature monitor, automatic 29 temperature setpoint 11 time display 11 transport 4 TWB 28 TWW 28
U
undertemperature protection 27 USER-ID card 41
W
wall bracket 9 weekday 15 weekly programmer 15
PERFECT page 54
Notes:
PERFECT page 55
PERFECT page 56
11.03.2005
VO englisch
D09851
Loading...