Melinera Z30252 User Manual

LED ROPE LIGHT

Assembly, operating and safety instructions

6

Z30252A -BS
Z30252B -BS
Z30252D -BS
Z30252E -BS

GB / IE Assembly, operating and safety instructions Page 3

1 x

20 x

2

20 x

20 x

31

3

4

LED rope light

Introduction

Before assembling and using the device
for the first time, take time to familiarise

yourself with the product first. In addition
please refer carefully to the installation and operating
instructions below and to the safety advice. Only
use the product as described and for the designated
areas of application. Please keep these instructions
in a safe place. If you hand this product on to a
third party, you must also pass on all documents
relating to the product.

Intended Use

This product is suitable for indoors and outdoor
use as decorative lighting. The appliance is only
intended for use in private households, and not
intended for commercial use.

Delivery scope

1 x LED rope light 10 m
20 x Attachment clips
20 x Cable tie

20 x Screw
 1 x Operating instructions

Description of parts

1

LED rope light

2

Attachment clips

3

Cable tie

4

Screw

Technical data

Rope light

Operating voltage: 230–240 V ∼ 50 Hz,

(22.5 W)

Bulbs: Z30252A-BS /

Z30252B-BS /
Z30252E-BS:
240 x 3 V
Z30252D-BS:
240 x 2 V

Note: bulbs are non-

replaceable.
Ambient temperature: from –15 °C to +30 °C
Protection class:
IP class: IP44 (splash-proof)
Length: 10 m
LED rope light (Model No. Z30252A / B / D / E-BS)

, 0.06 W

, 0.04 W

3 GB/IE

Z30252A-BS – transparent
Z30252B-BS – green
Z30252D-BS – yellow
Z30252E-BS – blue

Safety information

In the case of damage resulting from non-compliance
with these operating instructions the guarantee
claim becomes invalid! No liability is accepted for
consequential damage! In the case of material
damage or personal injury caused by incorrect
handling or non-compliance with the safety
instructions, no liability is accepted!

DANGER OF

DEATH AND ACCIDENTS FOR
TODDLERS AND CHILDREN!

Never leave children unsupervised with the
packaging material. The packaging material
represents a danger of suffocation. Children
frequently underestimate the dangers. Please
keep children away from the device at all times.

This device is not a toy and should not be played

by children. Children are not able to understand
the dangers that can occur when handling this
device.

Children or other individuals who do not know

or have no experience of handling this device,
or whose physical, sensory or mental abilities
are restricted, must not use the device without
supervision or instruction by an individual
responsible for their safety. Children must be
supervised in order to ensure that they do not
play with the device.

Avoid the danger of
death from electric shock!

Before use, ensure that the mains voltage

available is the same as the required operating
voltage for the device (230–240 V ∼).

Before connecting to the mains, always check

the product for any damage.

Never use the product if you find damage of

any kind.

The connecting cable cannot be repaired! If the

cable is damaged, the product must be taken
out of use and disposed of in the proper way.

This article does not contain any parts which

can be serviced by the user. The bulbs cannot
be replaced.

Never open any of the electrical parts or insert

any kind of object into them.

Protect the product from sharp edges, mechanical

loads and hot surfaces.
Do not install with sharp fasteners or nails.
Always remove the mains plug from the socket

before installing, dismantling or cleaning.
Never touch the mains plug or the LED rope

1

light

with wet hands.

CAUTION! RISK OF OVERHEATING!

Do not operate the LED rope light

1

in the

packaging or when it is rolled up.
Use the lighting only with the parts described

in these instructions.
If the LED rope light 1 is not to be used for

any length of time (e.g. holidays), disconnect

it from the power supply.
After use, keep the LED rope light 1 in the

packaging to prevent unwanted damage.

Keep away from ponds and other water reservoirs.

Install the LED rope light 1 at least 2 metres

away from water containers. Avoid place that

might flood after heavy rainfall.
This product is intended for use outdoors but

should be plugged into a socket which is located

in an indoor location (e. g. a shed, garage or

porch).
The socket into which this product is plugged

must be protected by a residual current circuit

breaker (RCD) with a trip current not greater

than 30 mA.
Sockets positioned outdoors for use with this

product should be of a type which is ade-

quately waterproof for an outdoor location

and should be located at least 2.5 m from the

nearest body of water or any location where

water may collect.

4 GB/IE

Make sure the LED rope light 1 is not laid

down in areas where lawn mowers, trimmers,
scissors or similar cutting tools are used.

Do not pull the LED rope light 1 and make

sure it is laid down properly so that no one
walks or trips over it.

If in any doubt about the safe installation or

use of this product, please consult a qualified
electrician.

Installation safety instructions

Make sure that the product is only installed by

competent persons.

The LED rope light 1 can be installed on all

normally inflammable surfaces with the enclosed
mounting parts.

CAUTION! RISK OF ELECTRIC SHOCK!

Make sure that there are no power, gas or water
lines located where you wish to drill. Check with
a cable and pipe locator if necessary before
you begin drilling.

Before installation, check whether the surface is

suitable for the mounting parts and the weight
of the LED rope light
consult an electrical specialist for advice.

Do not use sharp and / or pointed objects such

as wire, nails or fasteners for mounting.

Do not attach any additional objects to the

LED rope light

Avoid excessive bending of the LED rope

1

light

The bending radius of the rope must not fall

below the following value: rope diameter
between 10–14 mm: 2 cm.

Avoid excessive heating of the LED rope light 1.

A maximum of two sections of rope may cross
or run parallel to each other.

. This can damage the insulation.

1

. If you are in any doubt,

1

.

Installation

Note: The LED rope light 1 can be mounted on

all surfaces officially classified as being of “normal
flammability” by means of the supplied attachments.

Note: You will need a crosshead screwdriver in
order to mount the attachment clips
screws

4

.

Use the supplied attachment clips 2 and / or

the cable ties

3

to install the product.

2

and

Use

Plug the mains plug into the socket.
The lighting is switched on.
To turn the lighting off, remove the mains plug

from the socket.

Cleaning and care

CAUTION! RISK OF ELECTRIC
SHOCK! First remove the mains plug

from the socket.

Do not use any solvents, petrol or similar items.

This would damage the device.
Only a dry, lint-free cloth should be used for

cleaning.

Disposal

The packaging is made entirely of
recyclable materials, which you may
dispose of at local recycling facilities.

Contact your local refuse disposal authority for more
details of how to dispose of your worn-out product.

To help protect the environment, please
dispose of the product properly when it
has reached the end of its useful life and
not in the household waste. Information
on collection points and their opening
hours can be obtained from your local
authority.

EMC

5 GB/IE

IAN 74197

Milomex Ltd.

c/o Milomex Services

Hilltop Cottage

Barton Road

Pulloxhill

Bedfordshire

MK45 5HP

UK

Model No.: Z30252A-BS / Z30252B-BS / Z30252D-BS / Z30252E-BS

Version: 06 / 2012

© by ORFGEN Marketing

Last Information Update · Stand der Informationen: 05 / 2012

Ident.-No.: Z30252A / B / D / E-BS052012-6

6