Keep this booklet for future reference.
IMPORTANT: The remote control must not be exposed to excessive heat sources.
GB
I
TV
Digital
Thank you for choosing a Meliconi remote control.
Control TV Digital is the ideal remote for commanding a Digital or Analog television easily and comfortably. Thanks to its
extensive database it can control numerous TVs produced by a variety of brands on the market. The remote control has a
permanent memory, so it does not lose its settings even if there are no batteries in it.
USE OF THE BUTTONS AND FUNCTIONS
The functions of the buttons described below are available only if they are on your original device.
Indicator light
Numeric keypad
Selects an
Selects digital TV or radio
external input terminal
Volume control +/–
MUTE turns sound OFF and ON
For moving around within the MENU
TELEVIDEO buttons
To choose between
analog/digital
Displays the list of programmes
6 7
Selects the next programme P+
or previous programme P–
Specic buttons for controlling
the digital MENUS
Selects fastext functions or
submenus via colours
Selects the
screen display format
ON/OFF switches the device OFF and
in some cases ON
6
INSERTING THE BATTERIES
Before using the remote control, insert the batteries and programme it.
Do not leave at batteries inserted,
as liquid may leak and damage the remote control
SETTING THE CODE
SETTING CODES USING INTERNET
The remote control requires 2 new 1.5V alkaline AAA/LR03 batteries. Insert them
If they do not appear, repeat the procedure
as illustrated.
Try pressing a number button and check that the red light remains lit continuously
until you release the button. If the light ashes, the batteries inserted are not charged
and are about to go at, therefore you must substitute them.
The Control TV Digital remote control is a universal remote with a memory containing data regarding numerous devices
produced by different brands on the market.
Each original device has a specic code which must be used to set up the remote control.
So to use the Control TV Digital it is essential to insert the specic code of the TV you wish to command.
Use one of the following methods to identify the correct code and set it in your remote control:
A) - INTERNET (recommended)
B) - MOBILE PHONE (SMS)
C) - MANUAL SEARCH
If you have an Internet connection available, follow the on-line guide on the www.meliconi.com/guida website to identify
the specic code for the TV you wish to command. Then set the codes manually in your MELICONI remote control as
described below:
1. Press and hold down the ON / OFF and MUTE buttons on
the Meliconi remote simultaneously for 6 seconds.
2. Release the buttons. The indicator light ashes.
Immediately enter the specic code found previously
(e.g. 1306).
3. Three long ashes indicate a correct setting.
and
6 SEC.
SETTING CODES USING A MANUAL SEARCH
SETTING BY MOBILE PHONE
(this service is free; the only expense is due to sending the SMS, according to the fees applied by the mobile service carrier)
NOTE: If no SMS is received on the mobile phone or if the message
ERROR / NO CODE is displayed,
the system was not able to process the data; do not attempt to send it again and only use the MANUAL SEARCH to set
the code.
For those who do not have access to the Internet, MELICONI now provides the opportunity to receive the codes to be set
on the remote control directly on their mobile phones.
Write an SMS including the following: 1B, TV, Brand, Model
Fixed text that must always be entered
set the brand of the device to be controlled
set the model of the device to be controlled, usually found on a
label at the back of the device (if the model is unknown, do not write
anything after the brand)
1B, TV, PHILIPS,
EXAMPLE:
32PFL3614
1B, TV, PHILIPS, 32PFL3614
WARNING - separate data with a comma, and be as precise as possible so that the information system can search
for data and answer correctly.
Send the SMS to 0039 345 7518893 and wait for a reply by SMS.
After receiving the code list by SMS, set the rst code on the remote control as described in the ENTERING THE CODE
DIRECTLY procedure.
Stand in front of the device already turned on with the MELICONI remote control and press the ON/OFF button. If the
device does NOT turn off, try to set the next code on the SMS list on the remote control. Repeat the operation until
the device responds. When the device responds, conrm that the other buttons are also operating correctly. If so, the
remote control is ready to use. Otherwise, an inaccurate code, used for a very similar device, is being entered; ignore
the SMS list and see paragraph MANUAL SEARCH to identify a more suitable code.
(only to be performed if the specic code could not be found)
1. Turn on the TV you wish to command and select a
programme.
8 9
CHECK
Check that the other buttons correspond to the functions of the original remote control; if not, it is likely that the code
found is incorrect, but is used for a very similar device. In that case, repeat the procedure from point 2.
If the manual search for the code is successful, obtain the code in use by following the DISPLAY CODE IN USE
procedure and make a note of it inside the battery cover.
NOTE: During the search the indicator stops ashing and the remote control exits the programming mode in the
following cases:
• if for 12 seconds the button indicated is not pressed or if another button is pressed
• if the list of codes to nd is terminated. If this happens, go to the www.meliconi.com/guida website.
DISPLAY CODE IN USE
2. Press and hold down the ON / OFF and MUTE buttons
on the Meliconi remote simultaneously for 6 seconds
3. Release the buttons. The indicator light will ash.
Point the remote control at the TV and press the ON /
OFF. button. If the TV does NOT switch off, press the
same button again slowly (it may be necessary to press
the button several times).
4. When the TV responds correctly, press OK. Three long
ashes indicate that the operation has been carried out
correctly.
and
6 SEC.
If you set up the remote control using the MANUAL SEARCH
procedure, obtain and make a note of the code in use as follows:
1. Press and hold down the ON / OFF and MUTE buttons
simultaneously for 6 seconds.
and
6 SEC.
2. Release the button. The indicator light will ash. Press
the TV / radio button for an instant.
3. After a pause of several seconds, the indicator light pro-
duces four sets of ashes, spaced out, corresponding to
the code to be obtained. Count the number of ashes.
Each set of ashes corresponds to one gure in the
code. Ten ashes correspond to the gure 0.
4. Make a note of the code obtained on the label on the inside of the battery cover. You may need it in future.
Code obtained = 1306
TROUBLESHOOTING
PROBLEM
INFO - LINE
The device does not respond and the indicator light
does not come on when a button is pressed.
The device does not respond but the indicator light
comes on.
When you press a button the indicator light ashes
and the device does not respond to commands.
SOLUTION
Check that the batteries are charged and inserted
correctly and if necessary replace them with 2 new
1,5 V AAA/LR03 alkaline type batteries.
Make sure that the remote control is pointing at the
device and that there are no obstacles in the way.
If necessary, enter the remote control code
again by repeating the programming procedure.
Substitute the batteries, which are about to go at.
The remote control does not execute all commands
correctly.
You may be using an incorrect code.
Enter the remote control settings again by repeating
the programming procedure.
If you have any questions about the new Control TV Digital remote control:
carefully read this Instructions Booklet which will allow you to solve most problems
•
consult the www.meliconi.com website where you will nd all the answers you need quickly and easily.
•
2 year WARRANTY
Retailer stamp
The warranty is voided if the product is tampered
with or used improperly.
Remote control model Control TV Digital
Purchase date
The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the end of its useful life the product must be
collected separately from other waste. Therefore, at the end of the device’s life, you must take it to appropriate centres for the differentiated collection
of electrical and electronic waste, or return it to the retailer when purchasing a new device of equivalent type, on a one-for-one basis. Suitable
differentiated collection to allow subsequent recycling of the decommissioned device, with environmentally-compatible treatment and disposal, help
to prevent any negative effects on the environment and health and to promote the recycling of the materials of which the device is made. Improper
disposal of the product by the user will be subject to the sanctions in Legislative Decree No. 22/1997 (article 50 and subsequent articles of Legislative
Decree No. 22/1997).
10 11
Loading...