Meko Lighting RF433M User Manual

SAFETY INSTRUCTIONS FOR REMOTE

Safety instructions for remote

7

WW

C

Flash

Open

Push

Note: To replace the battery, please loosen the small screw on the back side of the remote, and refer to the diagram on the back side of

the remote.

Always purchase the correct size and grade of battery that is most suitable for the intended use.

Replace all batteries of a set at the same time.

Clean the battery contacts and also those of the device prior to battery installation.

Ensure that batteries are installed correctly with regards to polarity (+ and -).
Replace used batteries promptly.
Remove batteries from equipment when not used for an extended period of time.

WARNING: The remote contains a CR2025 DC 3V button battery. If swallowed, it could cause severe injury or death in just 2 hours.

Seek medical attention immediately.

IC Statement

Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.

Indoor LED Flexible Lighting Strip

ITM./ART.: 1234762

MODEL: DS18124

USE & CARE GUIDE

Important, Retain For Future Reference: READ CAREFULLY

Thank you for selecting DSI as your lighting choice for your home. With proper care,

this product will provide years of pleasure and enjoyment.

Carefully follow the installation instructions below in order to ensure that this product functions safely

and properly for years to come.

WW

C

Flash

120VAC 60Hz

DSI Customer Service Hotline: [phone] ext. 216 Mon.– Fri., 9:30 a.m. to 3:00 p.m. EST

DSI Customer Service Hotline: [phone] ext. 216 Mon.– Fri., 9:30 a.m. to 3:00 p.m. EST

Customer Service E-mail: [e-mail]

5101 NW 21st Ave, Suite 520, Ft Lauderdale, FL 33309 USA

MODEL: DS18124 MODEL: DS18124

E

Page 12 of 12

MADE IN CHINA

120VAC 60Hz

5101 NW 21st Ave, Suite 520, Ft Lauderdale, FL 33309 USA

Customer Service E-mail: [e-mail]

E

Page 1 of 12

MADE IN CHINA

REVISE DATE: 03/28/2017

SAFETY INSTRUCTIONS

Safety instructions:

1. Important! Main power voltage and fuse must meet the technical data specifications.
Before starting work, ensure that the main cable is not live. Switch off the fuse.

2. Fitting and maintenance work may only be carried out by a professional or an electrician
in accordance with local safety regulations.

3. All electrical connections must have good contact in order for this product to have a long, useful life.

4. LED chips of this LED strip can not be replaced.

5. This LED strip includes a linkable connector. Only link max two LED strips. Do not link more than
two strips together.

6. Please only use LED driver which has been provided with this LED strip.

7. Never use the unit in a room where there is a danger of explosion or in the vicinity of flammable
liquids or gases.

8. Do not bend, crush or pull the cable. Protect from sharp edges, oil and heat.

9. Do not touch the LED strip or electrical connector directly with hands.

10. For indoor use only.

11. Do not use the LED strip on a timer, wall switch with dimming functions, or with an extension cord.
Using the LED strip with any of these voids the warranty and results in the LED strip not
functioning properly. The remote included has dimming functions.

12. Danger of eye damage! Never look directly at the LED chips of this LED strip.

13. Always keep this user manual within reach while installing this LED strip. Please read and
understand the user manual to ensure proper installation and use. Always pay attention to the
technical data shown on the product. We reserve the right to make technical changes.

14. Electrical waste should not be disposed of with household waste. Please recycle where facilities
exist.

15. Warning: The adapter not for use with receptacles that are weatherproof only when the receptacle
is covered (attachment plug cap not inserted and receptacle cover closed).

16. Warning: Risk of electric shock. Mount the adapter at a height greater than 30 cm / 11.8 in. from
the ground surface.

17. Do not submerge any part of this unit.

18. CAUTION: If you choose to modify the length of the LED strip, only cut along the scissors marks.
Please contact DSI Customer Service for further instructions.

Note: Once the LED strip is cut, it will lose the connectable capabilities. You will not be able to

19. Ensure connectors and endcap are securely fastened before operating strip.

LED flexible lighting strip rating : 24VDC A.

20.

add a new connector or additional strips to the strip that had been cut.

TOOLS NEEDED (not supplied)

Phillips head
screwdriver

Brush

Pencil

Measuring
tape

120VAC 60Hz

DSI Customer Service Hotline: [phone] ext. 216 Mon.– Fri., 9:30 a.m. to 3:00 p.m. EST

MODEL: DS18124

5101 NW 21st Ave, Suite 520, Ft Lauderdale, FL 33309 USA

Customer Service E-mail: [e-mail]

E

Page 2 of 12

MADE IN CHINA

120VAC 60Hz

DSI Customer Service Hotline: [phone] ext. 216 Mon.– Fri., 9:30 a.m. to 3:00 p.m. EST

MODEL: DS18124

5101 NW 21st Ave, Suite 520, Ft Lauderdale, FL 33309 USA

Customer Service E-mail: [e-mail]

E

Page 3 of 12

MADE IN CHINA

PACKAGE CONTENTS

LED STRIP INSTALLATION

Carefully unpack and identify each part to make sure you have everything ready for installation. Lay out
each part on a clean flat area such as a table or carpet. Check to make sure you have the following:

* Parts are not to scale

NOTE: All parts and components sold together
in this package can only be used for this model.

Adapter

RF receiver and 3.66 m / 12ft

LED flexible strip (A) as one est

3.66 m / 12 ft LED flexible strip (B)

WW

C

Flash

Remote

Screw

(Includes 26 + 2 replacements)

Clip (type MH1)

1 PC

1 set

1 set

1 PC

28 PCS

12 PCS

Caution - To prevent personal injury and damage to the LED strip and/or mounting surface, do not pull
the LED strip from the surface. To reduce the likelihood of injury or damage, mount this LED strip only
on a surface that is structurally sound.

Remove any surface dust from the area where you will be

1

applying the LED strip.

Measure the desired space for the LED strip installation to determine if you

2

need to use one or two strips.

Note: Connect the LED strip (A) to the infrared receiver and adapter by aligning
the arrows on the connector leading from the infrared receiver to the connector
on the LED strip (A). If you require two LED strips, then connect the LED strip (B)
to the end of the LED strip (A) by aligning at the arrows on the connectors. Please
make sure the connectors are securely fastened all the way on both sides.

correct

A

correct

B

120VAC 60Hz

Wire clip 2 PCS

End cap 1 PCS

DSI Customer Service Hotline: [phone] ext. 216 Mon.– Fri., 9:30 a.m. to 3:00 p.m. EST

MODEL: DS18124

5101 NW 21st Ave, Suite 520, Ft Lauderdale, FL 33309 USA

Customer Service E-mail: [e-mail]

E

Page 4 of 12

MADE IN CHINA

120VAC 60Hz

correct

Note: If you are only using one LED strip for your installation please use LED
strip (A).

DSI Customer Service Hotline: [phone] ext. 216 Mon.– Fri., 9:30 a.m. to 3:00 p.m. EST

MODEL: DS18124

5101 NW 21st Ave, Suite 520, Ft Lauderdale, FL 33309 USA

Customer Service E-mail: [e-mail]

E

Page 5 of 12

MADE IN CHINA