Meiko SL-LR User Manual
SIDE LOADER
Standard SL-LR, SL-RL
Hooded SLH-LR, SLH-RL
Meiko’s 23” side loader accessory provides a reliable way
to make the most use of limited space in the dishroom.
Racks pushed into the front of the loader are engaged by
an extension of the dishmachine’s conveyor drive, and are
automatically advanced into the dishmachine through 90
degrees. Because the loader is powered by the Meiko rack
conveyor dishmachine, racks are automatically advanced
at the correct speed and no electrical connection is required.
The 23” side loader is available in standard or hooded
versions, and may be used with either K-Series or K-Tronic
Series rack conveyor dishmachines. Please specify the
machine type, direction and options at time of ordering.
RACK CONVEYOR
WAREWASHER
ACCESSORIES
Standard loader: Vent cowling
trimmed on front of machine
Hooded loader: Vent cowling
removed
Drive connection
extends 6-1/8"
into machine
Right-to-Left
Machines
Utility Connection:
Drain
D
See Page 2 for
connection information.
NOTE:
All dimensions
from floor are
+/- 1/2" due to
adjustable feet.
14-1/2"
D
8-1/2"
Drain connection 27-5/8" AFF
Hooded
loader
only
28-1/8"
3/4"
1"
9"
Table lip-in 34" AFF
Hooded
loader
only
1"
9"
Table lip-in 34" AFF
28-1/8"
3/4"
Drain connection 27-5/8" AFF
8-1/2"
D
14-1/2"
Standard loader: Vent cowling
trimmed on front of machine
Hooded loader: Vent cowling
removed
Drive connection
extends 6-1/8"
into machine
Left-to-Right
Machines
Utility Connection:
Drain
D
See Page 2 for
connection information.
NOTE:
All dimensions
from floor are
+/- 1/2" due to
adjustable feet.
14-3/4"
14-3/4"
23-3/8"
30"
Drive connection
extends 6-1/8"
into machine
5/8"
1-5/8" 20-3/8"
SL Side Loader • Updated 8-06 Meiko • 917 Airpark Center Drive • Nashville, TN 37217 • (800) 55-MEIKO • FAX (615) 399-6620 • www.meiko.us
20-3/8"
23"
D
1"
23-3/8"
30"
D
1"
23"
1-5/8"
Drive connection
extends 6-1/8"
into machine
5/8"
45°
section 1"
Vertical
backsplash 9"
Section A-A
20-3/8" clearance width
All holes
3/8" dia.
3/8"
Rear
backsplash
If wall backsplash is same height
as loader backsplash
Flashing
(weld in
place)
Weld
seam
If wall backsplash is lower than
loader backsplash
Front
rolled edge
AA
Stiffener plate
across rear
of panel seam
(weld in place)
Tabling to
include lip-in
For non-hooded
loaders, see inset
drawings at left for
wall flashing details
3/4"
Loader
4-1/8" 4-1/8" 4-1/8"4-1/8"2" 2"
C
L
Table 34" AFF
Plate, trim
to fit, weld
in place
On opposite end of machine from
loader, table width can be tapered at
either front or rear, as desired and
Flashing
(weld)
Weld
seam
Technical Specifications:
If wall backsplash is higher than
loader backsplash
Plate, trim
to fit, weld
in place
Weld
seam
SL Side Loader • Updated 8-06 Meiko • 917 Airpark Center Drive • Nashville, TN 37217 • (800) 55-MEIKO • FAX (615) 399-6620 • www.meiko.us
Flashing
(weld)
Overall Dimensions ...................................... 23”W x 30-1/8”D
Standard Loader:
• Backsplash height............. 9” vertical + 1” at 45° (10” total)
• Overall height .................................................................. 44”
Hooded Loader:
• Overall height, standard machine ........................... 57-7/8”
• Overall height, tall-hood machine ............................ 65-7/8”
Table Lip-In Height ..................................................... 34” AFF
Drain ........................................ 1-1/4” male NPT, 27-5/8” AFF
Wall clearances ........................................ As per table design
Note: All specifications are subject to change without notice
based on Meiko’s dedicated product improvement program.
permitted by space restrictions.
At time of ordering,
please specify:
Dishmachine Series
K-Series
K-Tronic Series
Loader Type
Standard (SL)
Hooded (SLH)
Direction of Operation
Left-to-Right (-LR)
Right-to-Left (-RL)
Loading...