Meiko PL-RL User Manual
POWER LOADER,
POWER UNLOADER
PL-LR, PL-RL, PU-LR, PU-RL
Meiko’s power loader and unloader accessories provide a
reliable way to make the most use of limited space in the dishroom.
Simply turning the loader or unloader on sets it into
operation whenever a rack enters. Racks are automatically
translated through 90° and loaded into either the
dishwasher (for loaders) or onto exit tabling (for unloaders).
The drive system is pre-set at the factory for the correct speed
settings for the dishmachine. No field adjustment is required.
Model PU power unloaders may be used with either KSeries or K-Tronic Series rack conveyor dishmachines.
Model PL power loaders may be used only with K-Series
rack conveyors. Please specify the machine type and
direction at time of ordering.
RACK CONVEYOR
WAREWASHER
ACCESSORIES
Vent cowling
trimmed for
rack clearance
22-3/4"
15-1/8"
Actuating lever for
unloader (not
present on loader)
Right-to-Left Loader
OR
Left-to-Right Unloader
D
plate 3/4"
Attachment
18-1/2"
Drain connection 29-1/4" AFF
11-1/4"
Attachment
plate 22-7/8"
Utility Connections:
Electric
Drain
D
See Page 2 for
connection information.
Water trough 29-3/4" AFF
Rack rail 34" AFF
Left-to-Right Loader
OR
Right-to-Left Unloader
plate 3/4"
Attachment
18-1/2"
Overall 34-1/2"
Overall 34-1/2"
Rack rail 34" AFF
Water trough 29-3/4" AFF
Drain connection 29-1/4" AFF
11-1/4"
NOTE:
All dimensions
from floor are
+/- 1/2" due to
adjustable feet.
rack clearance
D
Attachment
plate 22-7/8"
Vent cowling
trimmed for
22-3/4"
Actuating lever for
present on loader)
15-1/8"
unloader (not
14-3/4"
Actuating lever
3-1/4"
for loader (not
present on
unloader)
31-5/8"
34-3/8"
34-1/4"
34-1/4"
D
7-1/4"
20-7/8" 1"12-3/8"
34-1/4"
PL, PU Power Loader/Unloader • Updated 10-06 Meiko • 917 Airpark Center Drive • Nashville, TN 37217 • (800) 55-MEIKO • FAX (615) 399-6620 • www.meiko.us
34-3/8"
31-5/8"
3-1/4"
Actuating lever
for loader (not
present on
unloader)
D
20-7/8"1" 12-3/8"
34-1/4"
14-3/4"
7-1/4"
Section A-A
20-7/8" clearance width
Tabling
Rear
backsplash
Front
rolled edge
If flashing is used
(supplied by others),
allow clearance for
actuating lever.
All holes
3/8" dia.
4-15/16"
AA
Table 34" AFF
4-3/4" 4-3/4" 4-3/4" 4-3/4" 1-1/2"1-1/2"
C
L
Loader or
Unloader
1/2"
4-1/2"
2-1/2"
Table width can be tapered at either
front or rear, as desired and
permitted by space restrictions.
Technical Specifications:
Overall Dimensions .............. 34-1/4”W x 34-1/4”D x 34-1/2” H
Table Lip-In Height ....................................................... 34” AFF
Electrical:
• 208/230 V, 60 Hz, 3Ph, 0.6A or
• 460 V, 60 Hz, 3Ph, 0.3A
• Dedicated electrical supply (with circuit breaker/disconnect)
should be routed into electrical box from below. Terminal block
is at location shown.
Drain .......................................... 1-1/4” male NPT, 29-1/4” AFF
Wall clearances ......................................... As per table design
Note: All specifications are subject to change without notice based on Meiko’s dedicated product improvement program.
PL, PU Power Loader/Unloader • Updated 10-06 Meiko • 917 Airpark Center Drive • Nashville, TN 37217 • (800) 55-MEIKO • FAX (615) 399-6620 • www.meiko.us
At time of ordering,
please specify:
Dishmachine Series
K-Series
K-Tronic Series
Accessory Type
Power Loader (PL) *
Power Unloader (PU)
* Model PL may not be used with K-Tronic series dishmachines.
If a loader is needed with a K-Tronic machine, use 23” loader
model SL (standard) or SLH (hooded).
Direction of Operation
Left-to-Right (-LR)
Right-to-Left (-RL)
Loading...