Meiko K-L54V6N22P8 User Manual

HOT WATER SANITIZING

MULTIPLE-TAN K

RACK CONVEYOR

K-L54 SERIES

W AREWASHERS

The clean solution

Special Features:

• Industry-leading low water, energy and chemical consumption

Consuming only 0.15 gallons (0.57 liters) per rack, the M-iQ K-L series is one of the most efficient rack conveyor dishwashers in the world. Advanced technologies further reduce energy and detergent use.

• M-iQ Filter Technology Each tank features a multiple stage filtration process that first collects food soil, then flushes it out of the tank completely in high-pressure cycles. This improves performance, eases cleanup and reduces detergent consumption by up to 50%.

• M-iQ Airflow Management M-iQ features an advanced, fully integrated airflow system that retains and redirects hot air within the machine. This improves heating efficiency and reduces exhaust emissions.

• M-iQ Tank Management Each tank is equipped with an M-Filter system. Water levels are monitored and controlled intelligently and automatically. M-iQ automatically diverts water within the machine to maintain optimum level control and soil distribution.

• M-iQ Washing Dynamics M-iQ employs a higher-pressure wash for improved soil removal and reduced water consumption. Water flow has been modeled using computational fluid dynamics. Water, energy and chemical consumption are all dramatically reduced.

• M-iQ Energy Management M-iQ incorporates a 3-stage energy control system, as well as a variable-output booster heater, for optimal energy balance. The system dynamically adjusts to changes in heating distribution for minimal energy consumption.

• M-iQ Control System

M-iQ features a CC Touch glass touch screen with a high resolution color display. Screen information is customized based on the machine’s operating mode for fast, intuitive operation. Kitchen management, dishroom staff and service personnel can quickly call up customized information, or save data to the controller’s built-in memory.

• M-iQ Intuitive Cleaning M-iQ features an automatic cleaning mode. Assisted by the soil removal capabilities of the M-Filter, this dramatically reduces cleanup time. Areas that require regular manual cleaning are marked in effort by the staff.

This dishwasher is compliant with the Reduction of Lead in Drinking Water Act (201 1) amendment to the Safe Drinking W ater Act (SDW A).

Page 1 • M-iQ Rack Conveyor - K-L54 Series • Updated 7-14 • MEIKO • 1349 Heil Quaker Blvd. • LaVergne, TN 37086 • (800) 55-MEIKO • www.meiko.us • sales@meiko.us

blue for less wasted

Standard Features:

• Two wash chambers, each with 3 HP (2.2 kW) pump motor

• Power rinse chamber with 1 HP (0.75 kW) pump motor

• Pumped final rinse with 3/4 HP (0.55 kW) pump motor

• Integral heated blower dryer with 2/3 HP (0.5 kW) motor

• Choice of prewash sections:

• K-L54 V6 N** P8: 1’ 11-5/8” (600mm) prewash with 1 HP (0.75 kW) pump, 297.7 racks/hr., 0.15 gals. (0.57 liters)/rack

• K-L54 V8 N** P8: 2’ 7-1/2” (800mm) prewash with 3 HP (2.2 kW) pump, 297.7 racks/hr., 0.15 gals. (0.57 liters)/rack

• 304-series stainless steel construction

• Fully automatic operation. Prewash, wash, power rinse and final rinse are activated only when ware is present

• Front-sloping tanks for complete drainage and easier cleaning. Automatic self-cleaning and drain feature is accessed from control panel to eliminate manual drain levers

• Double-wall insulated construction on front, top and back improves operator safety, conserves heating energy, and reduces noise and heat loss into the dishroom. Insulation is fully waterproofed to eliminate heavy doors and unsanitary waterlogging

• Standard lifting doors are full-width for each chamber, including the blower drying zone, for improved access

• Pumps are vertically-mounted to be self-draining and easily removed for servicing. Pumps include safety alert feature to inform the operator of a leaking pump seal

Optional Features:

• Direct drive sideloader

• 90° curved loader or unloader

• Combination 90° curved unloader/heated blower dryer

• Hinged doors

• Drain water tempering

• Flanged, bolt-down feet

• Single-point electrical connection (electrically-heated machines only; standard on steam-heated machines)

M-iQ Rack Conveyor - K-L54 Series - Electric heat, left to right

(535mm)

7’ 5-3/8" (2269mm)

7' 1-3/8” (2169mm)

5' 4-3/8" (1634mm)

1' 9-1/8"

8' 6" (2590mm) recommended

8’ 3/4" (2459mm)

1-7/8"

(47mm)

2' 10" (864mm)

9" (229mm)

7-1/4" (184mm)

4' (1220mm) Recommended extraction area or

vent hood sizing and placement

(by others)

Additional blower dryers (if so equipped)

follow the standard blower dryer. Each is 1' 11-5/8" (600mm) long

3214

C W

1' 4-7/8” (429mm)

1’ 1-1/8” (334mm)

5' 6-1/4" (1684mm)

7' 9-1/4" (2369mm)

6’ 4-1/8” (1934mm)

2' 10" (864mm)

Vent hood

by others

1,2,3,4

3' (915mm)

Horizontal clearance

1' 8-1/2"

(520mm)

Vertical

clearance

1' 6-1/4"

(465mm)

Table lip-in

height 2’ 10”

(864mm)

1' 2-3/8" (365mm)

3-7/8" (100mm)

2” (50mm) MIN

TYP

2' 8-1/8" (815mm)

scrap screen

clearance

1’ 11-3/8”

(595mm)

Dishtabling shown for dimensional purposes only.All dishtabling to

be provided by others.

1" (25mm)

9-7/8" (250mm)

5-7/8”

(150mm)

1' 10-7/8" (580mm)

Prewash

V6: 1' 11-5/8"

(600mm)

V8: 2' 7-1/2"

(800mm)

Contact-plus zone 1

Wash 1

2' 7-1/2"

(800mm)

()N

Wash 2

2' 7-1/2"

(800mm)

Power rinse and

2' 7-1/2" (800mm)

Contact-plus zone 2

()N

final rinse

2' 5-1/8" (740mm)

Control panel

3' 3-3/8" (1000mm)

3-3/8"

1' 4-1/2"

(85mm)

(420mm)

W,C

3214

Blower dryer

1' 11-5/8"

(600mm)

Additional blower dryers (if so equipped)

follow the standard blower dryer. Each is 1' 11-5/8" (600mm) long

(400mm)

2-3/8" (60mm)

Contact-plus zone 1 (NA) Contact-plus zone 2 (NB) Model number code

None 7-7/8” (200mm) K-L54 V? N02 P8 7-7/8” (200mm) 7-7/8” (200mm) K-L54 V? N22 P8 11-7/8” (300mm) 11-7/8” (300mm) K-L54 V? N33 P8 1’ 3-3/4” (400mm) 1’ 3-3/4” (400mm) K-L54 V? N44 P8 1’ 7-5/8” (500mm) 1’ 7-5/8” (500mm) K-L54 V? N55 P8 1’ 11-5/8” (600mm) 1’ 11-5/8” (600mm) K-L54 V? N66 P8 2’ 7-1/2” (800mm) 2’ 7-1/2” (800mm) K-L54 V? N88 P8 3’ 3-3/8” (1000mm) 3’ 3-3/8” (1000mm) K-L54 V? N1010 P8

NOTE: As ware proceeds through the machine and closer to the final rinse, the water contacting the ware becomes warmer and cleaner. Large items and flat items (particularly sheet pans, trays, totes, etc.) can carry over cooler , soiled water forward in the machine. The contact-plus zone provides a landing area for this water, allowing it to return to the previous tank. This reduces detergent consumption and tank heating energy use.

Wider contact-plus zones also provide a surface that may be used to front-mount detergent or rinse aid systems.

Recommended contact-plus zone configurations:

• For machines washing plates/glasswares - N02

1' 3-3/4"

3' 1-3/8" (950mm)

access recommended

3' (914mm) service

Blower dryers

NOTE: All M-iQ rack conveyor warewashers feature at least one heated blower dryer section. One blower dryer provides good results for plates, cutlery and glassware in most cases.

For melamine ware or plastics (trays, insulated items, etc.) a second blower dryer is available, adding 1’ 11-5/8” (600mm) to overall machine length.

For some special ware types, additional blower dryer zone(s) beyond the second may provide improved drying results. Consult MEIKO for assistance.

When installing the unit in a corner, a 90° combination curved unloader/heated blower dryer is available as an option. This option may not be combined with additional drying zones.

1' 3-3/4" (400mm)

If optional 90° combination curved

unloader/heated blower dryer is

used, it replaces the standard

W,C

3214

Blower dryer

3' 1-/ " (945mm)4

blower dryer.

1’ 2-3/8”

(365mm)

3-7/8"

(100mm)

TYP

3' 1-3/8" (950mm)

access recommended

• For machines washing a typical ware mix - cafeteria trays and some sheet pans in addition to plates and glasswares - N22

• For machines washing containers - N33 or larger, depending on the size of the container

• For machines with front-mounted detergent and rinse aid dispensers - N33 or larger, depending on the size of the dispensing systems

Page 2 • M-iQ Rack Conveyor - K-L54 Series • Updated 7-14 • MEIKO • 1349 Heil Quaker Blvd. • LaVergne, TN 37086 • (800) 55-MEIKO • www.meiko.us • sales@meiko.us

3' (914mm) service

M-iQ Rack Conveyor - K-L54 Series - Electric heat, right to left

(

)

(

)

4' (1220mm)Recommended extraction area or

1-7/8"

(47mm)

Additional blower dryers (if so equipped)

follow the standard blower dryer.

Each is 1' 11-5/8" (600mm) long

vent hood sizing and placement

(by others)

Vent hood

by others

3' (915mm)

3 2 1 4

2369mm 4"

7' 9-1

6’ 4-1/8” (1934mm)

1' 3-3/4"

(400mm)

2-3/8" (60mm)

Blower dryer

1' 11-5/8"

(600mm)

3-3/8"

(85mm)

1’ 1-1/8” (334mm)

W,C

1' 4-7/8” (429mm)

5' 6-1/4" (1684mm)

1' 4-1/2" (420mm)

3 2 1 4

Control panel

3' 3-3/8" (1000mm)

2' 5-1/8" (740mm)

Power rinse and

final rinse

2' 7-1/2" (800mm)

Contact-plus zone 2

1' 10-7/8" (580mm)

Wash 2

2' 7-1/2"

(800mm)

()N

Wash 1

2' 7-1/2"

(800mm)

Contact-plus zone 1

2' 10" (864mm)

3' 1-3/8" (950mm)

service

914mm 3'

access recommended

Additional blower dryers (if so equipped)

follow the standard blower dryer. Each is 1' 11-5/8" (600mm) long

()N

Prewash

V6: 1' 11-5/8"

(600mm)

V8: 2' 7-1/2"

(800mm)

Contact-plus zone 1 (NA) Contact-plus zone 2 (NB) Model number code

Wider contact-plus zones also provide a surface that may be used to front-mount detergent or rinse aid systems.

Recommended contact-plus zone configurations:

• For machines washing plates/glasswares - N02

• For machines washing a typical ware mix - cafeteria trays and some sheet pans in addition to plates and glasswares - N22

2' 10" (864mm)

9" (229mm)

7-1/4" (184mm)

1" (25mm)

5-7/8”

(150mm)

1' 9-1/8"

(535mm)

7’ 5-3/8" (2269mm)

7' 1-3/8” (2169mm)

5' 4-3/8" (1634mm)

TYP

3-7/8" (100mm)

1' 2-3/8" (365mm)

9-7/8" (250mm)

2' 8-1/8" (815mm)

(595mm)

1’ 11-3/8”

clearance

scrap screen

Dishtabling shown for dimensional purposes only.All dishtabling to

be provided by others.

8’ 3/4" (2459mm)

8' 6" (2590mm) recommended

If optional 90° combination curved

2” (50mm) MIN

3' 1-3/8" (950mm)

3' (914mm) service

access recommended

Blower dryers

NOTE: All M-iQ rack conveyor warewashers feature at least one heated blower dryer section. One blower dryer provides good results for plates, cutlery and glassware in most cases.

For melamine ware or plastics (trays, insulated items, etc.) a second blower dryer is available, adding 1’ 11-5/8” (600mm) to overall machine length.

For some special ware types, additional blower dryer zone(s) beyond the second may provide improved drying results. Consult MEIKO for assistance.

When installing the unit in a corner, a 90° combination curved unloader/heated blower dryer is available as an option. This option may not be combined with additional drying zones.

1,2,3,4

unloader/heated blower dryer is

used, it replaces the standard

blower dryer.

1’ 2-3/8” (365mm)

3-7/8"

(100mm)

TYP

Blower dryer

3' 1-/ " (945mm)4

Horizontal clearance

1' 8-1/2"

(520mm)

Vertical

clearance

1' 6-1/4"

(465mm)

Table lip-in

height 2’ 10”

(864mm)

1' 3-3/4" (400mm)

W,C

3 2 1 4

• For machines washing containers - N33 or larger, depending on the size of the container

• For machines with front-mounted detergent and rinse aid dispensers - N33 or larger, depending on the size of the dispensing systems

Page 3 • M-iQ Rack Conveyor - K-L54 Series • Updated 7-14 • MEIKO • 1349 Heil Quaker Blvd. • LaVergne, TN 37086 • (800) 55-MEIKO • www.meiko.us • sales@meiko.us

+ 5 hidden pages