Page 1
Ages 8+
INSTRUCTION
Model No.: T38
MANUAL
Introduction
Thank you for purchasing this product, please read this maunal carfully before use and
retain it for future reference.
1. Coaxical-rotor design, built-in gyro insure more stable performance and make the
operation more easier. It is the best choice for beginner.
2. By using of latest infrared auto connection techonology, up to two helicopters can
be operated simultaneously with high stability.
3. Double protection( overcurrent and low-voltage) features ensure the security
of flying and longer product life.
Safety Guidelines
1. Please read this instruction manual carefully before playing and operate the product
according to the manual.
2. Keep the small accessories away from the kids to avoid accident.
3. Keep batteries away from fire or high temperature environment.
4. When flying the helicopter, keep it 1 ~ 2 meters away from user or others to avoid
injury due to collision.
5. Not to decompose or modify the product which may cause malfunction or accident.
6. Fly the helicopter within your eye vision for easy and safety control.
7. Need adult supervision when this helicopter is being played by children.
8. Only batteries of the same or equivalent type as recommended are to be used.
9. Insert batteries with correct polarity.
10. Non rechargeable batteries are not to be charged.
11. Do not mix old and new batteries.
12. Do not mix alkaline batteries, standard (Carbon-Zinc) or rechargeable (Nickel Cadmium) batteries.
13. Remove exhausted batteries from the battery compartment for the transmitter.
14. The power supply terminal are not to be short circuited.
15. Please retain this information for future reference.
16. Rechargeable batteries are to be removed from the toy before being charged(only for
AA type).
17. Rechargeable batteries are only to be charged under adult supervision.
Page 2
Product / Spare Parts Included in This Packaging
Power
A12
ON OFF
OPEN
Control Sticks
Helicopter Remote Control
Sketch - major Parts and Function Switches
Connector
Main Rotor
Searchlight
Charging
socket
Channel selector
Throttle control stick
Power switch
1
Stabilizer bar
Landing gear
2
compartment
Power
A12
ON OFF
OPEN
Charging
USB Charger
Tail Rotor
Light indicator
Forward/backward/
left/right control stick
Extra Tail Rotor
ON
OFF
Power switch
Gyro trim
Battery Installation
1. Install the control sticks.(Pic.1)
2. Unscrew counter clockwise to open the battery compartment cover.( Pic. 2 )
3. Install 4 X AA batteries into the battery compartment according to the given polarity. ( Pic. 3 )
4. Screw clockwise to close the battery compartment. (Pic. 4 )
Power
A12
ON OFF
OPEN
Pic. 1 Pic. 2 Pic. 3 Pic. 4
How to remove and insert batteries.
1
Page 3
Charging the Helicopter
(1) There are two ways available to charge the helicopter.
A. Use the remote control to charge to helicoper
● Open the cover of the charging compartment on the remote control
and take out the charging cable.
● Ensure the helicopter is in a “OFF” power status.
Plug the output jack of the charging cable into the charging socket
of the helicopter. Then, charging is beginning. (pic 5)
B. Use the USB charger to charge the helicopter
Connect the USB charger to the USB interface of the computer,
ensure that the helicoper is in a “OFF” power status, then, plug the
output jack of the USB cable into the charging socket of the
helicopter.(pic 6)
(2) The light of the remote control/USB charger is off when charging
is proceeding and will turn on automatically when charging is
done. Fully charge takes approximately 40 minutes.
Pic. 5
Pic. 6
Flight Environment
1. Indoor , stay away from unstable airflow generated by air conditioners or fans and without
table lamps or other dangerous objects.
2. Wide open space : Recommended minimum 3M ( wide ) x 5M ( length ) x 2.5M ( height )
3. Since this product is using of the infrared remote control technology, operating under
strong sun light or other any other light may cause lost of control.
Preparation for Flight
Must set the remote control at the “OFF” position before operating.
1. Turn on the helicopter and the searchlight will keep flashing rapidly.After a few seconds, the
searchlight will turn to slowly blinking,indicating that the helicopter is ready to connect with
the remote control.
2. Firstly, select the "A","1" or "2" channel;turn on the remote control and the power light of the
remote control will blink slowly; push the throttle control stick up to the top, then push it to the
bottom, the power light of the remote control will keep rapidly blinking, meaning that the
remote control is sending out connectional signal.Once signal connection is done, the power
light of the remote control will turn to constant "ON" without blinking.
3. Slowly push up the throttle stick and the helicopter takes off.
Hints
Select channel 1 and channel 2 and operate maximum 2 helicopters simultaneously.
Not to use the same channel by 2 helicopters at the same time.
Set the connection one by one. Otherwise, it may not be connected.
Once turn off the power. The connection procedure must be repeated to operate the
helicopter.
It is advised to select channel A if there's only 1 helicopter is playing.
2
Page 4
Operating
Upward
Downward
Turn left
Push up the left control
stick, the rotation speed
of the main rotor is
increasing and the
helicopter ascends
accordingly.
Push down the left
control stick, the
rotation speed of the
main rotor is decreasing
and the helicopter
descends accordingly.
Push the direction lever
to the left and the nose of
the helicopter will be
turning left.
Power
A12
ON OFF
OPEN
Power
A12
ON OFF
OPEN
Power
A12
ON OFF
OPEN
Turn right
Forward
Push the direction lever
to the right and the nose
of the helicopter will be
turning right.
When the helicopter is
flying,push up the right
control stick, the
helicopter nose will
incline down and then
moves ahead.
Power
A12
ON OFF
OPEN
Power
A12
ON OFF
OPEN
3
Page 5
Backward
When the helicopter is
flying,push down the
right control stick, the
helicopter nose will
incline upward and flies
reversely.
Power
A12
ON OFF
OPEN
Trimmer Functions
It's designed to adjust the helicopter flight alignment.
Power
A12
ON OFF
OPEN
Press the right gyro trim
Power
A12
ON OFF
OPEN
Press the left gyro trim
When flying the helicopter, if it keeps
spinning counterclockwise, press the
right gyro trim until it stops spinning.
When flying the helicopter, if it keeps
spinning clockwise, press the left
gyro trim until it stops spinning.
Circuit Protection Devices
1. The power light indicator of the helicopter will start to blink fast when the battery voltage of
the helicopter drops to certain level. The helicopter will be out of control. Recharge is
necessary to resume the function.
2. To protect the helicopter and prevent any risks caused by the stuck of the main rotor. The
main rotor will stop rotating and the power indicator light of the helicopter will keep blinking
fast when the main rotor is stuck or being blocked for 3 seconds. Pull the throttle joystick to the
lowest position to re-launch the helicopter.
Repair and Maintainance
1. Use wet cloth to clean this product.
2. Avoid this product to be exposed in the sunlight or the heated place.
3. Do not soak this toy in the water, otherwise the electronic part will be damaged.
4. Switch off the transmitter and power of the helicopter when it is not used.
5. Batteries should be taken out of the transmitter when it is not used for a long time.
6. You are highly suggested to use all-new alkaline battery to make sure the helicopter can
develop its best flying performance.
7. Periodically check the plug and other parts, If any damage is discovered, please do not use
it until it is completely repaired.
4
Page 6
Trouble Shooting
Problem Reason Solution
No reaction from
the helicopter.
Reaction from the
helicopter is not
sensitive
1. The helicopter is underpowered.
2. The transmitter is underpowered.
3. The channel of the RC does not
comply with the channel of the
helicopter.
1. Influenced by the sunlight or
strong light.
2. Another RC nearby is sending
out infrared signal of the same
frequency.
3. Another helicopter with the
same channel is being played
nearby.
1. Get the battery of the helicopter
charged.
2. Replace with new batteries in
the RC.
3. Turn the channel switch to get
the correct channel
1. Choose a better place to avoid
the helicopter exposure to strong
sunlight or other strong light.
2. Change another place where there
is no infrared.
3. Slide the channel switch of the RC
to another channel.
5
Loading...