Page 1
ITEM NO.F47/F647
Page 2
Thank you for purchasing this product. Please read this manual carefully
before use and retain it for future reference.
Technical parameter of the helicopter
Fuselage Length:235MM
Overall height: 80MM
Gear Ratio: 8:1 Charging Time: about 70 minutes
Gross Weight: about 49g
Battery: Li-polymer 3.7V
Tail Rotor Diameter: 50MM
Main Rotor Diameter: 225MM
Motor: N30
Introduction
With single-rotor design and built-in gyro, the helicopter is more flexible
and much stronger.
New designed structure makes assembly and maintainance easier.
Adopting 2.4G auto connection technology, scores of helicopters can be
played at the same time.
With high power capacity of 3.7V 380mAh li-polymer battery, flight time is
about 8 minutes.
LCD remote control is included.
Safety Guidelines
This product is not a toy. It is not applicable for children who are under
14 years old.
Please read this instruction manual carefully before playing and operate
the product according to the manual.
The users are in full charge of proper operating the helicopter. The
manufacturer and dealers disclaim all responsibility for the damage
caused by misuse.
Keep the small accessories away from the kids to avoid accident.
Keep batteries away from fire or high temperature environment.
When flying the helicopter, keep it 1~2 meters away from user or others
to avoid injury due to collision.
Not to decompose or modify the product which may cause malfunction
or accident.
Fly the helicopter within your eye vision for easy and safety control.
Need adult supervision when this helicopter is being played by children.
Only batteries of the same or equivalent type as recommended are to be
used.
Insert batteries with correct polarity.
Non rechargeable batteries are not to be charged; the transmitter need
4XAA batteries for work.
Do not mix old and new batteries.
1
Page 3
Product/spare parts included in this packaging
Description
Helicopter 1
Remote controller
Rotor blade
Qty(pc)
1
2
Description
3.7V 380mAh li-polymer battery
Manual
Tail Rotor 1
Qty(pc)
2
1
USB charger 1
The LCD Remote controller
Main features of the remote controller
2.4G, LCD reomote control, scores of helicopters can be played at the
same time.
Control function:upward,downward, forward, backward,leftward,
rightward, turning left and turning right.
Throttle control stick can be freely switched according to player's habit.
Sketch and function switches of the remote controller
8. Antenna
7. Power switch
1. Left stick
11. Throttle changing
button (Left)
3. Trimmer A
4. Trimmer B
12.flight mode
changing button
13.aileron/rudder
changing button
No. Function switch Function description
1
2
3 Trimmer A
Left stick
Right stick
Remote Controller
STICK MOD2:upward/downward,turn left/turn right;
STICK MOD4:upward/downward,leftward/rightward.
STICK MOD1:forward/backward,turn left/turn right;
STICK MOD3:forward/backward,leftward/rightward.
STICK MOD1: upward/downward,leftward/rightward;
STICK MOD3: upward/downward, turn left/turn right;
STICK MOD2: forward/backward,leftward/rightward;
STICK MOD4: forward/backward,turn left/turn right.
In stick Mod 2 and 4, this button is null.
In stick Mod 1and 3, it helps to tune the helicoper's
forward and backward flight.
POWER
(Transmitter)
9. Power indicator
6. Trimmer D
2. Right stick
5. Trimmer C
10.Throttle limit knob
11. Throttle changing
button (Right)
2
Page 4
No. Function switch Function description
In stick Mod 3 and 4, it helps to tune the helicopter's
4
5 Trimmer C
6 Trimmer D
7
Trimmer B
Power switch
sideward flight.
In stick Mod 1 and 2,it helps to tune the helicopter's
left and right direction turning speed.
In stick Mod 3 and 4, it helps to tune the helicopter's
left and right direction turning speed.
In stick Mod 1 and 2,it helps to tune the helicopter's
sideward flight.
In stick Mod 1 and 3, this button is null.
In stick Mod 2 and 4, it helps to tune the helicoper's forward
and backward flight.
It controls the power source of the transmitter.Slide
the power switch to the “ON” position, the transmitter
is powered on; slide the power switch to the “OFF”
position, the transmitter is powered off.
8
9
10
11
12
13
Antenna
Power
indicator
Throttle limit
knob
Throttle
changing button
flight mode
changing button
aileron/rudder
changing button
Transmits wireless signal.
The indicator light keeps blinking slowly: the transmitter
is not activated.
The indicator light keeps flashing rapidly: the transmitter
is sending out connectional signal to the helicopter.
The indicator light keeps on without blinking: the
transmitter is ready for controlling the flight.
The throttle of the helicopter can be adjuted by this button,
player can use this button to increase or decrease the
helicopter's upward/downward speed.
Slide down or slide up the 2 buttons at the same time
to select the throttle control stick
There are 3 flight modes of the helicopter: low speed, medium
speed and maximum speed.
Also named Stick Mode changing button.Press this button
to change the control stick mode.
Remote controller’s setting
Select the throttle control stick
There is 1 throttle button on either side of the remote controller.
Slide both of the 2 buttons to "R", the right stick is the throttle control stick.
Slide both of the 2 buttons to "L", the left stick is the throttle control stick.
Tip: both of the 2 buttons should be either on the position of "R" or "L",
otherwise, the remote controller can not be activated.
3
Page 5
POWER
Pic.1 Pic.2
Activate the LCD remote controller
Slide the power switch to "ON" position after throttle control stick selection
is done.To activate the remote controller, slowly push up the throttle control
stick to the top and then push it down to the bottom. The remote controller
is activated once a beep sound is heard. Then, the indicator light keeps
flashing while the remote controller is sending out connectional signal. It
takes about 10 seconds to finish the signal transmission process. After
signal transmission is completed, the indicator light keeps constant "on”.
User can turn either the left stick or the right stick to skip the signal
transmission process and enter into the start-up interface directly.
Stick Mode Selection
There are 4 flight modes available for selection: Stick Mod 1 (Pic.3)
Stick Mod 2 (Pic.4) Stick Mod 3 (Pic.5) Stick Mod 4 (Pic.6)
Forward /
Backward
control
Left/Right
turning
control
Throttle
control
Leftward/
Rightward
control
Pic.3
Throttle
control
Left/Right
turning
control
Forward /
Backward
EXIT/
LIGHT
MENU/
OK
PUSH
control
Leftward/
Rightward
control
Pic.4
STICK MOD:1 STICK MOD:2
Forward /
Backward
control
Leftward/
Rightward
control
Throttle
control
Left/Right
turning
control
Pic.5
Throttle
control
Leftward/
Rightward
control
Forward /
Backward
control
POWER
Left/Right
turning
control
Pic.6
STICK MOD:3 STICK MOD:4
Flight mode selection
There are 3 flight mode available: low speed, medium speed and maximum
speed.Player can select the flight speed by pressing the flight mode button.
4
Page 6
STICK MOD
CH
1
STICK MOD
2
CH
1
2
STICK MOD
CH
1
2
00
This is the low speed icon. This is the medium speed icon. This is the maximum speed icon .
Pic.7 Pic.8 Pic.9
00
00
The helicopter
connector
rotor blade
landing gear
How to charge the helicopter
battery compartment
This helicopter is included with USB charger.
Before charging, please disconnect the battery power plug from
helicopter PBC cable plug.Then, connect the battery power plug to the
USB cable and insert the USB interface to any equipment which is with
USB interface.
When the battery is underpowered, the charging light of the USB is off;
when the battry is full charged, the charging light of the USB is on.Full
charge taks about 70 minutes.
stabilizer bar
Tail motor
battery connector
Pic.8
Computer
5
Page 7
Preparation for flight
Turn on the remote control. To activate the remote controller,slowly
push up the throttle stick to the top and then push it down to the bottom.
The remote controller is activated once you hear a beep sound.Then, the
indicator light flashes rapidly while the remote controller is sending out
connectional signal.
Connect the battery plug to the helicopter battery cable,the indicator
light of the helicopter will keep slowing flashing,set the helicopter down
to a platform. Once the helicoter receives the connecting signal,the
indicator light of the helicopter will keep flashing rapidly to check the
gyro,then,push up the throttle stick slowly to takes off the helicopter.
If the helicopter is flying slightly to one side, please use the trimmer
button to tune it to balance.
Check and regulate the swashplate of the helicopter
The swashplate of the helicopter should be kept horizontal, otherwise, the
helicopter will fly forward/backward/leftward/rightward automatically even
though no control signal is given. Hence, it is very important to check and
confirm that the swashplate is horizontal before flying the helicopter. To
get the swashplate horizontal, there are two ways available for regulation.
(1) If the swashplate is slightly inclined, it is okay to regulate the trimmer
button of the remote control to get the swashplate retain horizontal.
(2) If the swashplate is greatly inclined, then, it should be better to
regulate the length of the servo connecting bar to get the swashplate
parallel to the ground. The operation instruction are specific as follow:
6
Page 8
A.When the helicopter is hovering but still
keeping flying forward automatically,
please take out the elevator servo
connecting bar, then, clockwise rotate
the bar for one circle(360°). How many
circle should be regulated will depend
on the tilt angle of the swashplate.
the elevator servo
connecting bar
swashplate
the aileron servo
coneecting bar
Pic9
Generally, rotate the bar for one or two
circles for one regulation.(Pic 10)
B.When the helicopter is hovering but still
keeping flying backward automatically,
please take out the elevator servo
connecting bar, then, counter-clock wise
rotate the bar for one circle (360°). How
screw the elevator
servo connecting
bar clockwise or
counter clockwise
Pic10
many circle should be regulated will
depend on the tilt angle of the swashplate.
Generally, rotate the bar for one or two
circles for one regulation. (Pic 10)
C.When the helicopter is hovering but still
screw the aileron
servo connecting
bar clockwise
or counter
clockwise
keeping flying leftward automatically,
please take out the aileron servo connecting bar, then,
Pic11
clockwise rotate the bar for one circle(360°). How many circle should be
regulate, will depend on the tilt angle of the swashplate. Generally, rotate
the bar for one or two circles for one regulation.(Pic 11)
D.When the helicopter is hovering but still keeping flying rightward
automatically, please take out the aileron servo connecting bar , then,
counter-clockwise rotate the bar for one circle(360°). How many circle
should be regulate, will depend on the tilt angle of the swashplate.
Generally, rotate the bar for one or two circles for one regulation. (Pic 11)
the bottom plane of the
swashplate
Parallel
Extension line
of the helicopter
Pic12
Tips
7
Page 9
Trimmer Functions
If the helicopter keeps moving forward/backward even there is no control
signal given, users may adjust the elevator trim to keep the helicopter
balanced.
STICK MOD 1 or 3:
If the helicopter keeps moving
backward, push up Trimmer A
until it gains balance.
If the helicopter keeps moving
forward, push down Trimmer A
until it gains balance.
STICK MOD 2 or 4:
If the helicopter keeps moving
backward, push up Trimmer D
until it gains balance.
If the helicopter keeps moving
forward, push down Trimmer D
until it gains balance.
If the helicopter keeps moving leftward/rightward even there is no control
signal given, users may adjust the aileron trim to keep the helicopter
balanced.
STICK MOD 3 or 4:
If the helicopter keeps moving
leftward, turn right of Trimmer B
until it gains balance.
If the helicopter keeps moving
righttward, turn left of Trimmer B
until it gains balance.
8
Page 10
STICK MOD 1 or 2:
If the helicopter keeps moving
leftward, turn right of Trimmer C
until it gains balance.
If the helicopter keeps moving
righttward, turn left of Trimmer C
until it gains balance.
If the helicopter keeps spinning even there is no control signal given,
users may adjust the rudder trim to keep the helicopter balanced.
STICK MOD 1 or 2:
If the helicopter keeps spinning
counterclockwise in the air,turn
right of Trimmer B until it gains
balance.
If the helicopter keeps spinning
clockwise in the air,turn left of
Trimmer B until it gains balance.
STICK MOD 3 or 4:
Operating
Upward
If the helicopter keeps spinning
counterclockwise in the air,turn
right of Trimmer C until it gains
balance.
If the helicopter keeps spinning
clockwise in the air,turn left of
Trimmer C until it gains balance.
Push up the throttle control stick, the
rotation speed of the mains rotors are
increasing and the helicopter ascends
accordingly.
9
Page 11
Downward
Push down the throttle control stick,
the rotation speed of the mains rotors
are decreasing and the helicopter
descends accordingly.
Turn left
Turn right
Forward
Backward
Leftward flight
Rightward flight
Turn the left/right turning control stick
to the left,the helicopter will left.
Turn the left/right turning control stick
to the right,the helicopter will right.
When the helicopter is flying, push up
the forward/backward control stick, the
helicopter will move forward.
When the helicopter is flying, push
down the forward/backward control
stick, the helicopter will move backward.
Turn the sideward flight control stick to
the left side,the helicopter will fly
leftward.
Turn the sideward flight control stick to
the right side,the helicopter will fly
rightward.
Trouble shooting
Problem
1.The helicopter is underpowered. 1.Get the battery of the helicopter charged
No reaction
from the
helicopter
2.The indicator light of the helicopter
flashing rapidly, and the gyo is in
the testing statement
3.the helicopter and the transmitter
is out of radio connection
Reason Solution
2.Set the helicopter down to a platform, until the
indicator light turn to constant ”ON” without
blinking.
3.Repeating the connection procedure.
10
Loading...