EX-G013A / EX-G013B
EX-G015/EX-G017B / EX-G016
EX-G076A / EX-G076B
HDMI over Single CAT5 Distribution Series
Page 1 of 23
EX-G013A
EX-G017A/ EX-G017B / EX-G015
EX-G076A EX-G076B
User Manual
EX-G016
EX-G013B
Safety and Notice
The HDMI over Single CAT5 Distribution Series, including
EX-G013A 1x2 HDMI over Single CAT5 Distribution Amplifier,
EX-G017A 1x9 HDMI over Single CAT5 Distribution Amplifier,
EX-G017B 1x9 HDMI over Single CAT5 Distribution Amplifier with 7.1ch audio,
EX-G015 2x8 HDMI 1.3 over Single CAT5 Matrix Switch,
EX-G013B 1x2 HDMI over Single CAT5 Cascading Distribution Amplifier,
EX-G016 2x8 HDMI 1.3 over Single CAT5 Cascading Distribution Amplifier,
EX-G076A HDMI over Single CAT5 Receiver, and
EX-G076B HDMI over Single CAT5 Mini-Receiver
has been tested for conformance to safety regulations and requirements, and has been certified
for international use. However, like all electronic equipments, the HDMI over CAT5 Distribution Series
should be used with care. Please read and follow the safety instructions to protect yourself from
possible injury and to minimize the risk of damage to the unit.
z Follow all instructions and warnings marked on this unit.
z Do not attempt to service this unit yourself, except where explained in this manual.
z Provide proper ventilation and air circulation and do not use near water.
z Keep objects that might damage the device and assure that the placement of this unit is on a
stable surface.
z Use only the power adapter and power cords and connection cables designed for this unit.
z Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device
before cleaning.
Page 2 of 23
HDMI
Introduction
The HDMI over Single CAT5 Distribution Series provides the most flexible solution by which the
high definition video and high quality audio can be transmitted to different locations over a long
distance. The devices are cascadable, allowing you to extend HDMI/DVI compliant displays almost
anywhere.
Diagram 1
HDMI source
HDTV
Speaker
Audio cable
HDMI cable
HDTV
Speaker
Audio cable
HDMI cable
HDMI cable
EX-G013A
CAT5 cable
EX-G013B
CAT5 cable
HDTV
cable
Speaker
Audio cable
EX-G076B
CAT5 cable
EX-G013B
HDTV
CAT5 cable
EX-G076A
Page 3 of 23
EX-G076B
Diagram 2
HDMI source
EX-G076B
HDTV#1
HDMI cable
HDMI cable
CAT5e cable up to 25m (80ft)
CAT5e cable
CAT5e cable
up to 60m (200ft)
EX-G076B
HDTV#2
CAT5e cable
EX-G017A/
CAT5e cable
EX-G076B
EX-G076B
EX-G017B
HDTV#8
Page 4 of 23
HDTV#3
EX-G076A
HDMI cable
HDMI cable
EX-G076A
HDTV#4
HDTV#7
EX-G076A
EX-G076A
HDMI cable
HDMI cable
HDTV#6
HDTV#5
Features
z State-of-the-art Silicon Image (founder of HDMI) chipset embedded for upmost compatibility and
reliability
z HDMI 1.2a compliant (EX-G015 & EX-G016 are HDMI 1.3c compliant)
z HDCP compliant
z Regenerates the HDMI signal
z Supports audio output
z Supports default HDMI EDID and has the ability to learn the EDID of displays
z Extends up to 15m (50ft) of input HDMI cable
z Extends up to 15m (50ft) of output HDMI cable
z Extends up to 60m (200ft) (720p / 1080i) of output CAT5 cable
z Extends up to 40m (130ft) (1080p) of output CAT5 cable
z Minimize the cable skew by adjustable 8-level equalization control [EX-G015/EX-G017) / EX-G013B /
EX-G016
z Pure unaltered uncompressed 7.1ch digital HDMI over LAN cable transmission
]
z Allows
cascading
z Perfectly integrated with other HDMI over CAT5 series products
z 1U rack mountable [EX-G017A / EX-G015 / EX-G017B /
EX-G016]; wall mountable [EX-G013A /
EX-G013B]
The length depends on the characteristics and quality of the cables. Higher resolutions and
longer transmission distances require low skew cables (<25ns/100m) for best performance.
Unshielded CAT6 with metal RJ-45 connectors is recommended.
Page 5 of 23
Technical Specifications and Package Content
Model Name EX-G013A EX-G013B
Technical
Role of usage
HDMI compliance HDMI 1.2a
HDCP compliance Yes
Video bandwidth Single-link 165MHz [4.95Gbps]
Video support 480i / 480p / 720p / 1080i / 1080p60
HDMI over LAN cable
transmission range
Audio support Surround sound (up to 7.1ch) or stereo digital audio
Equalization None 8-level digital control
Input TMDS signal 1.2 Volts [peak-to-peak]
Input DDC signal 5 Volts [peak-to-peak, TTL]
[1] Human body model — ±15kV [air-gap discharge] & ±8kV [contact
ESD protection
PCB stack-up
Input 1x HDMI 1x RJ-45
Output
HDMI connector Type A [19-pin female]
RJ-45 connector WE/SS 8P8C with 2 LED indicators
3.5mm connector Earphone jack for stereo audio
DIP switch 2-pin for EDID/audio mode None
Mechanical
Housing Metal case
Dimensions
[L x W x H]
Weight
Fixedness Wall-mounting case
Power supply 5V 4A DC
Power consumption 3 Watts [max]
Operation temperature
Storage temperature
Relative humidity 20~90% RH [no condensation]
Package Contents
Model 180 x 108 x 27mm [7”x4.3”x1.1”]
Package 330 x 200 x 95mm [1’1”x7.9”x3.7”]
Carton 495 x 440 x 380mm [1’7.5”x1’5.3”x1’3”]
Model 430g [15.2oz]
Package
discharge]
[2] Core chipset — ±8kV
Transmitter [TX] Transceiver [TRX]
Full HD (1080p)-40m (130ft) [CAT5e] / 50m (165ft) [CAT6]
HD (720p/1080i)-50m (165ft) [CAT5e] / 60m (200ft) [CAT6]
4-layer board [impedance control — differential 100Ω; single 50Ω]
1x 3.5mm audio socket
1x2 distribution amplifier
1x HDMI
1x RJ-45
1x 3.5mm audio socket
0~40°C [32~104°F]
-20~60°C [-4~140°F]
1x EX-G013A or EX-G013B
1x 5V power adapter
1x User Manual
1x HDMI
1x RJ-45
430g [15.2oz]
Page 6 of 23
Model Name EX-G017A / EX-G017B EX-G015 EX-G016
Technical
Role of usage
1x9 distribution amplifier 2x8 matrix switch
Transmitter [TX] Transceiver [TRX]
HDMI compliance HDMI 1.2a HDMI 1.3c
HDCP compliance Yes
Video bandwidth
Single-link 165MHz
[4.95Gbps]
Single-link 340MHz [10.2Gbps]
Video support 480i / 480p / 720p / 1080i / 1080p60
HDMI over LAN cable
transmission range
Full HD (1080p)-40m (130ft) [CAT5e] / 50m (165ft) [CAT6]
HD (720p/1080i)-50m (165ft) [CAT5e] / 60m (200ft) [CAT6]
Audio support Surround sound (up to 7.1ch) or stereo digital audio
Equalization None 8-level digital rotary control
Input TMDS signal 1.2 Volts [peak-to-peak]
Input DDC signal 5 Volts [peak-to-peak, TTL]
[1] Human body model — ±15kV [air-gap discharge] & ±8kV [contact
ESD protection
discharge]
[2] Core chipset — ±8kV
PCB stack-up
Input 1x HDMI 2x HDMI
Output
4-layer board [impedance control — differential 100Ω; single 50Ω]
1x HDMI
1x RJ-45
1x HDMI
8x RJ-45
8x RJ-45
7x HDMI
1x RJ-45
HDMI connector Type A [19-pin female]
RJ-45 connector WE/SS 8P8C with 2 LED indicators
DIP switch 8-pin DIP 6-pin DIP 2-pin DIP
Mechanical EX-G017A / EX-G017B EX-G015 EX-G016
Housing Metal case
340x110x44mm
[1’1.4”x4.3”x1.7”]
1.4kg [3.1 lbs]
2.2kg [4.8 lbs]
Dimensions
[L x W x H]
Weight
Model 438 x 158 x 44mm [1’5.2”x6.2”x1.7”]
Package 545 x 230 x 110mm [1’9.5”x9.1”x4.3”]
Carton 570 x 580 x 260mm [1’10.5”x1’10.9”x10.2”]
Model 1.4kg [3.1 lbs] 1.4kg [3.1 lbs]
Package 2.2kg [4.8 lbs] 2.2kg [4.8 lbs]
Fixedness 1U rack-mount with ears
Power supply 5V 4A DC
Power consumption 13 Watts [max]
Operation
temperature
Storage temperature
0~40°C [32~104°F]
-20~60°C [-4~140°F]
Relative humidity 20~90% RH [no condensation]
1x EX-G017A / EX-G017B / EX-G015 / EX-G016
Package Contents
2x Rack-mounting ears
1x 5V power adapter
1x User Manual
Page 7 of 23
s
Model Name EX-G076A EX-G076B
Technical
Role of usage Receiver [long range RX] Receiver [short range RX]
HDMI compliance HDMI 1.2a
HDCP compliance Yes
Video bandwidth Single-link 165MHz [4.95Gbps]
Video support 480i / 480p / 720p / 1080i / 1080p60
HDMI over LAN cable
transmission range
Audio support Surround sound (up to 7.1ch) or stereo digital audio
Equalization 8-level digital control None
Input TMDS signal 1.2 Volts [peak-to-peak]
Input DDC signal 5 Volts [peak-to-peak, TTL]
ESD protection
[CV-715]
PCB stack-up
Input 1x RJ-45 1x RJ-45
Output 1x HDMI 1x HDMI
HDMI connector Type A [19-pin female] Type A [19-pin male]
RJ-45 connector WE/SS 8P8C with 2 LED indicators
Mechanical
Housing Metal case Plastic mold
Model 85 x 60 x 25mm [3.3”x2.4”x1”] 45 x 25 x 20mm [1.8”x1”x0.8”]
Dimension
[L x W x H]
Weight
Fixedness Wall-mount case upon request Direct plug-in
Power supply 5V 2A DC None
Power consumption 1 Watt [max] 0.5 Watt [max]
Operation temperature
Storage temperature
Relative humidity 20~90% RH [no condensation]
Package Contents
Package
Carton 450 x 370 x 300mm [1’5.7”x1’2.6”x11.8”]
Model 154g [5.4oz] 22g [0.8oz]
Package 453g [1 lb] 90g [3.2oz]
[1] Human body model — ±15kV [air-gap discharge] & ±8kV [contact
discharge]
[2] Core chipset — ±8kV
Full HD (1080p)-40m (130ft) [CAT5e] / 50m (165ft) [CAT6]
HD (720p/1080i)-50m (165ft) [CAT5e] / 60m (200ft) [CAT6]
4-layer board [impedance control — differential 100Ω; single 50Ω]
270 x 175 x 80mm
[10.6”x6.9”x3.2”]
1x EX-G076A
1x 5V power adapter
1x User Manual
170 x 115 x 40mm [6.7”x4.5”x1.6”]
0~40°C [32~104°F]
-20~60°C [-4~140°F]
1x EX-G076B
1x User Manual
Page 8 of 23
Panel Descriptions
EX-G013A 1x2 HDMI over Single CAT5 Distribution
Amplifier
1
3 2
1. Power indicator
2. DIP switch [see table below]
3. HDMI In: Connect a HDMI source with a HDMI M-M cable here
4. Audio out: Plug in a local speaker here
5. HDMI Out: Connect to a HDMI display with a HDMI M-M cable here
6. RJ-45 Out: Link to EX-G013A for cascading; or link to CV-715 or CV-715s to another HDMI
5 4
7 6
display with a CAT5e/6 LAN cable
7. +5V DC: Connect to 5V 4A DC power supply
DIP Switch
Position
Video Audio Description
Pin#1 Pin#2
OFF
[©]
OFF
[©]
OFF [©] 1080p
ON [ª]
ON [ª] OFF [©]
ON [ª] ON [ª]
720p
1080i
Bypas
4
s
Bypas
s
Stereo
Stereo
Bypas
s
Stereo
Default Mode
1
HDTVs
Safe Mode3 – Enforce the system output at 720p/1080i video
and stereo audio for basic compatibility among HDTVs
EDID Learning Mode
4
while playing any received HDMI audio format
EDID Learning & Stereo mode
the display while enforcing stereo output if any HDTV cannot
play surround sound normally
Note for EDID (Extended Display Identification Data) learning
1. Don’t plug in HDMI cable to [HDMI In] when you want to restore default EDID or learn the display’s
EDID.
2. Please connect the display which you want to read EDID to HDMI Out so the EX-G013A can learn the
EDID information from the connected HDTV.
3. To learn EDID from HDMI display, pull up-and-down the DIP switch 1 from OFF to ON, the green light
will dim and light to indicate the EDID learning process is complete. You DON’T NEED to pull up the
DIP switch again unless you want to learn another EDID by pulling DIP switch 1 up and down.
Page 9 of 23
2
– 1080p & stereo audio output for most
5
– for learning EDID from the display
5
– for learning EDID from
Note
1
If the HDTV shows video but without audio, please try to set audio mode to stereo.
2
Factory default: Pin#1-OFF[©], Pin#2- OFF[©] for 1080p with stereo.
3
If you encounter any unsolved audio/video output problem during system installation, please turn to
Safe Mode (Pin#1-OFF[©] & Pin#2-ON[ª]) to enforce the most compatible 720p stereo output for
system check.
4
Bypass means the matrix will maintain playing the original format of HDMI signals in video and
perhaps audio. By setting at this mode, the users may encounter compatibility issue among different
kinds of HDMI sources and displays. If you cannot get the audio and/or video output normally at the
system installation, please change the DIP switch setting to de fault mode or even safe mode to v erify
the functionality of the device.
5
Set Pin#1 at ON[ª] first then connect the HDMI Input to HDTV through a HDMI cable. W ait for 20
seconds. The EDID learning procedure will be finished. If you want to learn the EDID from another
HDTV, you must set Pin#1 at OFF first and repeat this procedure.
EX-G013B 1x2 HDMI over Single CAT5 Cascading
Distribution Amplifier
1
2
3
4 5
6
1. Power indicator
2. 16-level rotary control: Adjust the 16-level equalization control corresponding to the
transmission distance of receiving HDMI signals. For surround sound audio output, please
adjust from 0-to-7 (longest-to-shortest transmission length). For stereo audio output, please
adjust from 8-to-F (longest-to-shortest transmission length). It is recommended to adjust
from 7-to-0 or from F-to-8 to find the optimal visual experience.
3. RJ-45 In: Link to EX-G007-TX, EX-G013A, or EX-G013B with a CAT-5e/6 cable
4. Audio out: Plug in a local speaker here
5. HDMI Out: Connect to a HDMI display with a HDMI M-M cable here
7
6. RJ-45 Out: Link to another EX-G013B for cascading; or link to EX-G076A or EX-G076B to
another HDMI display with a CAT5e/6 cable
7. +5V DC: Connect to 5V 4A DC power supply
Page 10 of 23
EX-G017A/B 1x9 HDMI over Single CAT5 Distribution Amplifier with
7.1ch audio
1. Power jack 5V DC
2. HDMI input: connect a HDMI source here
3. HDMI output: connect a local HDMI display here
4. DIP switch: see the definition below
5. Rotary controller: see the definition below
6. Out1-Out8: RJ45 output 1-8: link to the HDMI over CAT5 receiver EX-G076A or EX-G076B; or
cascade to EX-G016
2 1
3
4 5
6
DIP switch
The EX-G017A & EX-G017B can display HDMI signals on DVI devices by configuring each DIP
switch.
DIP Switch: OFF[©] for HDMI display / ON[ª] for DVI display
Green LED: Bright when HDMI input signal is detected; dim when DVI input signal is detected.
For example: Output 1 to HDMI TV and Output 2 to DVI monitor. Set DIP switch at Pin#1- OFF[©] and
Pin#2- ON[ª] position.
Page 11 of 23
Video Patterns
The Rotary controller on EX-G017A allows you to send several test patterns.
Mode 0 (EX-G017A): Stereo audio mode
Mode 0 (EX-G017B): Surround sound audio mode
Mode 1 (EX-G017A): Running circles Mode 2: Running circles with changing radius
Mode 1 (EX-G017B): Stereo audio mode
Mode 3: White running circle with black background Mode 4: Black running circle with white
background
Mode 5: Color bar Mode 6: Mosaic
Mode 7: Check board I Mode 8: Check board II
Page 12 of 23
Mode 9: Pure red Mode A: Pure green
Mode B: Pure blue Mode C: Pure black
Mode D: Pure white Mode E: Write default EDID
Mode F: Save EDID from the display connected to HDMI Out
Note for EDID (Extended Display Identification Data) learning
1. Don’t plug in HDMI cable to HDMI input connector while processing writing default EDID or
writing display’s EDID.
2. Please connect the display which you want to read EDID to HDMI Out and turn Mode to F
for 5-10 seconds so the BTM18 can learn the EDID information from the connected HDTV.
3. Turn Mode clockwise from Mode F to Mode 0 and enjoy the experience. DO NOT let the
rotary arrow pass by Mode E which will erase the EDID just learned and set back to default
EDID.
EX-G076A HDMI over Single CAT5 Receiver
HDMI-OUT: Connect to a HDMI display with a HDMI M-M cable here.
EQ: Adjust the 8-level equalization control knob to the received HDMI signals. 0 – 7 = strongest –
weakest. It is recommended to switch from 7 to 0 to find the optimal visual experience.
Page 13 of 23
EQ
HDMI-OUT
EX-G015 2x8 HDMI over Single CAT5 Matrix Switch
1. +5V DC : Power jack for 5V4A DC
2. HDMI In1: HDMI Input1 for connecting to a HDMI source here
3. HDMI In2: HDMI Input2 for connecting to a HDMI source here
4. EDID: DIP Switch (see the definition in the next section)
5. Out1 – Out8: RJ-45 Output 1-8 to link to the HDTV through HDMI over CAT5 receiver
EX-G076A or EX-G076B
DIP Switch
Switch
Position
Pin#1
Pin#2
Pin#3
Pin#4
Pin#5
Pin#6
1
Set pin#2-ON [ª] firstly and then connect the HDMI Input to HDMI display through HDMI
cable. Waiting for 20 seconds, the learning procedure will be accomplished. When update
the EDID content with another display, you must set pin#2-OFF[©] and repeat this
procedure again.
2
Set pin#3-ON [ª] firstly and then connect the HDMI Input to HDMI display through HDMI
cable. Waiting for 20 seconds, the learning procedure will be accomplished. When update
the EDID content with another display, you must set pin 3 off and repeat this procedure
again
3
While 7.1 channel option is selected for the HDMI signal with only stereo audio, the
HDMI display may show video without audio. In this case, please set audio to stereo
audio.
4 3 2 1
OFF [©] ON [ª]
Input HDMI source #1 Input HDMI source #2
Source 1 use default EDID
Source 2 use default EDID
7.1 Channel
HDMI 1.2 output HDMI 1.3 output
HDMI mode output DVI mode output
3
5
Source 1 use learned EDID
Source 2 use learned EDID
2 Channel
1
2
Page 14 of 23
EX-G016 2x8 HDMI over Single CAT5 Cascading Distribution
Amplifier
Front Panel
1
2
4 3
1. 1.2a/1.3a: Output format LED indicator [Green: HDMI 1.3 / Red: HDMI 1.2]
2. Format Sel: Push button for HDMI output format selection
3. IN 1/IN 2: Input LED indicator [Green: HDMI input / Red: RJ-45 input]
4. IN Sel: Push button for input HDMI source selection
Rear Panel
5. Dip Switch: EDID/Audio setting [see following section]
6. EQ: Rotary control for equalizer setting [see following section]
7. RJ-45 IN 1: for cascading from another EX-G016 or EX-G013B
8. HDMI IN 2: for connecting to video source, EX-G013A, EX-G017A, or another EX-G016
9. RJ-45 OUT: for connecting to display through EX-G076A or EX-G076B; or for cascading to
another EX-G013B or EX-G016
10. HDMI OUT1-HDMI OUT7: for connecting to display through HDMI cable or through Cat-5e cable
with EX-G076B attached; or for cascading to another EX-G013A, EX-G017A, or EX-G016.
11. +5V DC power: connect to 5V 4A DC interlocking power adapter
12. Power ON/OFF switch
Page 15 of 23
5 6 7 8 9 10 11 12
DIP Switch
Pin#1
Position
EDID Mode
OFF
Use Default
Note
1
Set pin#1-ON[ª] first and then connect the HDMI Input to HDMI display thru HDMI cable. Wait
for 20 seconds. The Recording Procedure will be finish. If you want to learn the EDID for
another equipped display, you must set pin#1-OFF[©] and repeat the procedure.
2
If the equipped display shows video but without audio, please try to set audio to 2 channel.
Rotary Control
In order to adapt the CAT5 cable, EX-G016 offers 8 level equalization control on the
received HDMI signal. The strongest equalization is applied while the knob stops at
number 0, while the weakest equalization happens at number 7. It is recommended to
switch from 7 to 0 to find the optimal visual experience.
[©] ON [ª]
Use learned
EDID
EDID
Pin#2
Position
1
Audio Mode
[©] ON [ª]
OFF
7.1
Channel
Stereo
2
HDMI Output Format Selection
When input signal exists, the output format LED turns on. If the input HDMI source is HDMI 1.3
format, you can set the output format to HDMI 1.2 mode and Red LED will be on. If the input HDMI
source is HDMI 1.2, the output format is always set to HDMI 1.2.
Page 16 of 23
Hardware Installation
EX-G013A
Extends HDMI signals to next cascading device with one local display
1. Switch off all devices, including monitors.
2. Connect a local HDMI display to the HDMI out of the EX-G013A and then connect a speaker to the
3.5mm audio socket.
3. Connect to a HDMI source (such as a Blu-Ray Disc player)
4. Connect EX-G013A to EX-G013B (for cascading), to EX-G076A (to HDTV at long range), or
EX-G076B (to HDTV at mid range) via RJ-45 Out by a CAT5 cable.
5. Plug in 5V 4A DC power supply.
6. Power on the HDTV.
7. Power on the HDMI source.
Page 17 of 23
HDMI source
HDMI cable
EX-G013A
Audio cable
Speaker
CAT5 ca ble
HDMI cable
EX-G013B
EX-G076A
EX-G076B
HDTV
EX-G013B
Relays HDMI signals to next cascading device with one local display
1. Switch off all devices, including monitors.
2. Connect a local HDMI display to the HDMI Out of the EX-G013B and then connect a speaker to the
3.5mm audio socket.
3. Connect to EX-G013B via RJ-45 in by a CAT5 cable.
4. Connect to next EX-G013B (for cascading), to EX-G076A (to HDTV at long range), or EX-G076B
(to HDTV at mid range) via RJ-45 out by a CAT5 cable.
5. Plug in 5V 4A DC power supply.
6. Power on the HDTV.
EX-G013A
CAT5 cable
EX-G013B
Audio cable
HDMI cable
CAT5 cable
EX-G013B
EX-G076A
Speaker
EX-G076B
HDTV
Page 18 of 23
EX-G017A / EX-G017B
Broadcasts HDMI signals to 8 remote displays and one local display
1. Switch off all devices, including monitors.
2. Connect a local HDMI display to the HDMI Out of the EX-G017A or connect to EX-G013A for
cascading.
3. Connect a HDMI source (such as a Blu-ray Disc player) to the HDMI In.
4. Connect to the receivers (EX-G076A or EX-G076B) via RJ45 connectors by a CAT5e cable.
5. Plug in 5V 4A DC power supply.
6. Power on the HDMI monitors.
7. Power on the HDMI source.
Page 19 of 23
HDMI source
HDMI cable
EX-G017A
EX-G017B
HDMI cable
HDTV
EX-G076B
HDTV
EX-G076A
HDTV
EX-G015
Broadcasts HDMI signals to 8 remote displays from either of two HDMI
sources
HDMI source #2
EX-G076B
HDTV#1
HDMI cable
HDMI cable
CAT5 cable up to 25m (80ft)
CAT5 cable
CAT5 cable
up to 60m (200ft)
EX-G076B
HDTV#2
HDMI source #1
CAT5 cable
EX-G015
CAT5 cable
EX-G076B
EX-G076B
HDTV#8
Page 20 of 23
HDTV#3
EX-G076A
HDMI cable
EX-G076A
HDMI cable
HDTV#4
HDMI cable
HDTV#5
HDTV#7
EX-G076A
EX-G076A
HDMI cable
HDTV#6
EX-G016
Broadcasts HDMI signals to 7 HDMI displays and cascade to another
EX-G016
HDMI Pin Definition
Pin 1 TMDS Data2+ Pin 8 TMDS Data0 Shield Pin 15 SCL
Pin 2 TMDS Data2 Shield Pin 9 TMDS Data0– Pin 16 SDA
Pin 3 TMDS Data2– Pin 10 TMDS Clock+ Pin 17 DDC/CEC Ground
Pin 4 TMDS Data1+ Pin 11 TMDS Clock Shield Pin 18 +5 V Power
Pin 5 TMDS Data1 Shield Pin 12 TMDS Clock– Pin 19 Hot Plug Detect
Pin 6 TMDS Data1– Pin 13 CEC
Pin 7 TMDS Data0+ Pin 14 Reserved (N.C. on device)
Page 21 of 23
Notice
1. If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to
retrieve and provide DVI/HDMI EDID information.
2. All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz
LAN cable and ASTRODESIGN Video Signal Generator VG-859C.
3. The transmission length is largely affected by the type of LAN cables, the type of HDMI sources,
and the type of HDMI display. The testing result shows solid LAN cables (usually in bulk cable
300m/1000ft form) can transmit a lot longer signals than stranded LAN cables (usually in patch
cord form). Shielded STP cables are better suit than unshielded UTP cables. A solid UTP CAT5e
cable shows longer transmission length than stranded STP CAT6 cable. For long extension users,
solid LAN cables are your only choice.
4. EIA/TIA-568-B termination (T568B) for LAN cables is recommended for better performance.
5. To reduce the interference among the unshielded twisted pairs of wires in LAN cable, you can use
shielded LAN cables to improve EMI problems, which is worsen in long transmission.
6. Because the quality of the LAN cables has the major effects in how long transmission distance will
be made and how good is the received display, the actual transmission length is subject to your
LAN cables. For resolution greater than 1080i or 1280x1024, a CAT6 cable is recommended.
7. If your HDMI display has multiple HDMI inputs, it is found that the first HDMI input [HDMI input #1]
generally can produce better transmission performance among all HDMI inputs.
Performance Guide for HDMI over LAN Cable Transmission
Performance rating Type of LAN cable
Wiring Shielding CAT5 CAT5e CAT6
Solid
Stranded
Page 22 of 23
Unshielded
(UTP)
Shielded (STP)
Unshielded
(UTP)
Shielded (STP)
Termination
Please use EIA/TIA-568-B termination (T568B) at any time
Limited Warranty
The SELLER warrants the HDMI over Single CA T5 Distribution Se ries to be free from defects in
the material and workmanship for 1 year from the date of purchase from the SELLER or an authorized
dealer. Should this product fail to be in good working order within 1 year warranty period, The SELLER,
at its option, repair or replace the unit, provided that the unit has not been subjected to accident,
disaster, abuse or any unauthorized modifications including static discharge and power surges.
Unit that fails under conditions other than those covered will be repaired at the current price of
parts and labor in effect at the time of repair. Such repairs are warranted for 90 days from the day of
reshipment to the BUYER. If the unit is delivered by mail, customers agree to insure the unit or
assume the risk of loss or damage in transit. Under no circumstances will a unit be accepted without a
return authorization number.
The warranty is in lieu of all other warranties expressed or implied, including without limitations,
any other implied warranty or fitness or merchantability for any particular purpose, all of which are
expressly disclaimed.
Proof of sale may be required in order to claim warranty. Customers outside Taiwan are
responsible for shipping charges to and from the SELLER. Cables are limited to a 30 day warranty and
cable must be free from any markings, scratches, and neatly coiled.
The content of this manual has been carefully checked and is believed to be accurate. However,
The SELLER assumes no responsibility for any inaccuracies that may be contained in this manual.
The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages
resulting from any defect or omission in this manual, even if advised of the possibility of such damages.
Also, the technical information contained herein regarding the HDMI over Single CAT5 Distribution
Series features and specifications is subject to change without further notice.
Page 23 of 23
Loading...