Meicheng ADR-605R User Manual

M

M

e

eii

c

c

h

h

e

e

n

n

g

g

ADR-605R

Digital Audio System

DAB + FM + CD Player / CD Recorder

USER MANUAL

www.meicheng.com.tw

®

1

Table of Contents

1. Foreword

2. Package Contents

3. Functions

4. Controls & Features

5. Remote

6. Installation

7. Basic Operation

8. Cautions & Maintenance

9. Troubleshooting Guide Line

10. Specifications

！

！

LLaasseerr WWaarrnniinnggs

s

：

：

DDiiggiittaall AAuuddiioo SSyysstteemm---- DDAASS iiss eeqquuiippppeedd wwiitthh aa llaasseerr

ddeevviiccee ..UUnnddeerr aannyy ccoonnddiittiioonnss ,, DDOO NNOOTT wwaattcchh tthhee LLaasseerr ppiicckk--uupp
hheeaadd ,, tthhee llaasseerr bbeeaamm iiss ttoottaallllyy eenncclloosseedd aatt aallll ttiimmee..

! Precaution for the first time power on the audio recording

For the first time Power On, please press the “Autotune” key and hold about 2 seconds then
ADR – 605R can auto-searching all DAB broadcasting stations.

To finish the recording, you MUST press remote the “Finalize” key to format this CD-R/RW
disc. Then this disc can be played with other CD/VCD/DVD Players.

CAUTION:

◎ DO NOT twist the optical cable to avoid damage.
◎ Both the optical and coaxial will be outputted in the same time when you use the digital

audio output. You can select the optical or coaxial output by ADR-605R.

2

◎ Please “Power Off “ADR-605R before connection or removing any audio devices.
◎ Please refer to ADR-605R User’s Manual for others information.

1. Foreword

We are highly appreciated you to purchase Digital Audio System – ADR – 650R.
This machine is contented DAB + FM Receiver & CD Player + CD Recorder Hi- Fi Audio
System.

You can store the Perfect Audio through ADR – 605R.

Please reference this User’s Manual first before you operating ADR – 605R.

2. Package Contents

When you open the package, please check the accessories as follows “Accessory List“.

ADR-605R or ADR-605C Audio Cable*1 AC Power Cable*1

Antenna*1

User’s Manual

ADR-605R

Digital Audio System

DAB + FM + CD Player / CD Recorder

User’s Manual

AAA battery*2

Remote *1

3

3. Functions

Optical Cable*1

DAB + FM Receiver

DAB – Digital Audio Broadcasting is broadcasted the audio via digital technique to lessen
the analog signal interference and distortion during the transporting. It is offered the
audience the CD quality audio.

CD - Player

ADR – 605R can be played the CD discs.

CD - Recorder

DAS can record Audio into CD-R, CD-RW either from DAB /FM or External Audio source.

S/PDIP Optical & Digital Audio Output

It is equipped the S/PDIF Optical Digital Output. You can enjoy the 5.1 channel, Home
Theater Hi-Fi Audio effect through the Optical Cable or Coaxial Cable to connect the D / A
converter / Amplifier.

Others

◎ Real time OSD (On Screen Display), it can be showed the broadcast channel / CD

/Operation information.

◎ CD Next / FF / Prev /FR scanning.

ADR-605R don’t support CD-ROM / DVD-ROM / VCD / DVD / SVCD /
DVD-R/RW / DVD+R/RW disc.

The CD disc would be auto ejected if it can not be correctly identified after
15 ~ 20 seconds, or you can manual eject the disc.
Please remove the disc and double check the CD specific is matched the
machine or any abnormal on the disc. For the detail information, please
refer to Chapter 9 “Troubleshooting Guide Line”.
Remark:

! Caution of the CD can not be playing

4

4. Controls & Features

H

J

A

B

C

I

D E F

（A）.Power On / Standby （B）.CD Eject / Insert

（C）.Switch to CD Mode

（D）.Stop CD Player or Record

G

（F）.CD Record (ADR-605R only)

（E）.Start CD Play or Pause

O M L

P

N

（J）.Program Channel Selection (Up /Down

/Enter)

（I）. CD Tray

（G）.Switch to DAB/FM Mode

K

（H）. LCD Screen

(K). AC Power Socket
(L). External Audio INPUT Terminal, R / L
(M). Analog Audio OUTPUT Terminal, R / L
(N). Digital Audio Coaxial OUTPUT Terminal
(O). Digital Audio Optical OUTPUT Terminal
(P). Antenna Terminal

5. Remote

CAUTION:
◎ Please use two “AAA” type batteries. DO NOT use two different types battery or mixing

new and old battery in the same time.

◎ Remote should be kept out of the High Temperature / Humidity environment.
◎ DO NOT disassemble, take parts of the Remote.
◎ Follow the arrow direction to open the battery cover to replace new 2 * AAA (1.5V)

batteries.

◎ Misuses the battery may cause the liquid leaking or explosion. You should clean the

battery case set before install the new battery if you found the battery liquid leaking.

◎ Please remove the battery if you will not use the remote for a long period of time to

avoid the battery leaking and corrosive the battery case.

◎ Please DO NOT mix alkalinity and carbon-hydrogen battery using in the same time to

avoid the explosion accident.

Note：

Remote function area within 9.0 meters , operation angle area is 45o side by side (Left
/Right either direction is 22.5o ).

5

9

M

22.5

o

6

「 , 」 5.4

「Enter」 5.3

「 」 5.1

「 」 5.2

「+」「-」5.6

「 , 」5.5

5.1「Power」

ADR – 605R – Power On / Standby

5.2「Band」

Switch DAB or FM band

5.3「Enter」

Press “Enter” to play the selected program after chosen the DAB / FM channel.

5.4「Next/FF」

Play CD, press this button then it will be jumped to the next track. Press this key and hold
about 2 seconds, it will become the fast forward play.

5.5「Prev /FR」

Play CD, press this button then it will be jumped to the previous track. Press this key and
hold about 2 seconds, it will become the fast rewind play.

5.6「＋」、「－」 Up , Down

In DAB/FM mode, Up/Down is used to switch the channels.

7

5.7「REC」 CD Record

Recording CD-R/RW, you have two modes to option as follows:
(1) Record DAB/FM channels: Receiving the DAB/FM programs press “REC” to record the

program at real time. Press “STOP” or “BAND” to stop recording.

(2) External Audio Source: You should press “CD” key to switch to CD mode, connecting

the external audio source via cable then press “REC” to function.

「Vo1+ / Vo1-」5.16

「 」 5.11

「 」 5.12

「 」5.13

「Mute」5.14

「 」5.10

「 」5.7

「Erase」5.8

「Finalize」5.9

5.8「Erase」 Erase CD-RW Disc only

Press “Erase“, it can erase CD-RW (Re - Writable) disc all materials.
(1) Switch to CD mode first, then the “Erase” function can be work.
(2) Press “Erase” to erase the last track.
(3) Press “Erase” and hold it about 2 seconds to erase full disk.

5.9「Finalize」CD-R / RW Disc

Press “Finalize“ to format the CD-R / RW disc and playable in others CD/VCD/DVD players.
Not finalized disc, it just can play in this player.
The Finalized CD-R /RW disc can not be recorded again.
You should erase the entire finalized CD – RW disc first then you can record the disc again.

5.10「Stop」

Press “STOP“, the CD will be stopped the play or record.

5.11「Play/Pause」

Press this button to play CD. Press 2nd time, the CD Player will be pause.

8

5.12「Eject」CD Tray In / Out

Press “Eject”, the CD Tray will be Opened / Closed.

5.13「CD」 Switch to CD Mode

Switch the system to CD Mode.

5.14「Mute」

Press Mute one time, all of the Audio output mute. Press it again to release mute function.

「Sleep」5.19

「AutoTune」5.22

「Auto Select」5.21

「Manual」5.20

「Display」5.18

「M1~M4」5.17

「Repeat」 5.15

5.15「Repeat」

It has 5 Repeat modes to play CD: Normal, Single, Single Repeat, Disc Repeat, and
Random.

5.16「Vol+ / Vol-」

Volume control (The Digital output can not be controlled), it is controlled the analog output
volume.

5.17「M1 ~ M4」Memory

If you want to store the radio stations / channels, please select the program / channel which
you want to store and then press one of the preset (M1~M4) key and hold about 2 seconds
to store it. The LCD screen will show “preset # stored”. If you want to listen the preset
channels, you just need to press the corresponding memory key (M1~M4). The LCD screen
will show “preset # empty” if there was no preset any channels / programs.

5.18「Display」 LCD Information Display

Displays the various statuses of modes as DAB, FM, CD play, and recording, please see
the details in Chapter 7.

9

5.19「Sleep」 Sleep & Alarm Setup

There are two functions of the 「Sleep」 key . One is “auto turn of f” and another is “Alarm”.
You can set the “Alarm” time if you press this key and hold about 2 seconds. Please see the
details in Chapter 7.

5.20「Manual」 Manual Channel Selection

You can use this function to find the channel after the antenna adjusted, or have the newly
additional radio stations which are not found by auto tune search. Please see the details in
Chapter 7.

5.21「Autoselect」 Auto Channel Selection

LCD screen will be showed the “Autoselect On” when you press this key, after this, you can
use 「+」、「-」Up/Down button to select a program and listen it without pressing “Enter”.

5.22「Autotune」

There are two modes to scan channels. Please see the details in Chapter 7.

10

6. Installation

The CD – RW disc which you recorded the audio from DAB programs or external audio
is equivalent to the original one.

6.1 Installation with analog audio amplifier system

Audio Cable

Analog Audio System

Right

Left

10

Analog 2CH

11

Note：

◎ You can connect ADR – 605R to AUX、CD or LINE IN terminals on the audio system.

Also you can set your audio system on AUX、CD mode to enjoy ADR – 605R.

6.2 Installation with Digital Amplifier system

You can connect this unit to a digital amplifier simply with built-in AC-3 decoder for 5.1
audio tracks and you will enjoy the theater-like surrounding audio effect.

Dolby Digital (AC-3) is a theater-like 5.1-track digital surrounding audio system. The Digital
amplifier who is supported (AC-3) has the Dolby mark on the machine. There are two front
speakers, one central speaker, two rear speakers and a double bass speaker to set as an
AC-3 5.1 sound track surrounding audio system.

Digital Audio System

Coaxial Cable (Optional)

Digital Audio O/P: Digital Coaxial

Digital Optical Cable

Digital Audio O/P : Optical

12

7. Basic Operation

DAB Mode

First Time Power On

Connect the AC power to ADR – 605R.

Connect the Antenna and put it on the best signal receiving place.

AC Power: 90~240V

When power on please press 「Autotune」 and hold it about 2 seconds. It will be scanned
the all DAB channels.

During the scanning, the LCD screen will be showed the black blocks and increasing the
blocks one by one to indicate the scanning status and the scanned channels.

DAB (Digital Audio Broadcasting) – is total different to the general broadcast – is grouped
several channels and launched / broadcasted it by one frequency. These Groups are
named “multiplexes” and “ensembles”. When you searched the group then the group name
will be showed on the LCD screen. E.g.: BBC National DAB.

13

When the “autoscan” was finished, ADR – 605R will be showed the first searched group /
channel by alphabet sequence.

Display Channel / Program (DAB or FM)

ADR – 605R Modes

Dynamic Letter Show (DLS)

If you can not receive any signal, please adjust the volume tuner according to clock
direction until the expected volume.
If you want to select more new channels, press 「＋」, 「－」 Up/Down buttons to select
the channels one by one. When you selected the channel, press「Enter」, then it will be
jumped to the selected channel. If you did not press “Enter”, the LCD screen will be

returned to the original channel after 4 seconds later.

Autoselect

When you selected the channel, you can press「Enter」 or set ADR – 605R to play the
searched radio channels by order. Autoselect can be scanned channels fast. After you
selected the channel, press “Autoselect“ to start this function, then the “Autoselect ON” will

be showed on the LCD screen. Next time, when you press「＋」 ,「－」 Up/Down keys, it
will be searched the next radio channel automatically and no need to press “ Enter “.

Press「Autoselect」and hold 2 seconds until the LCD screen is showed the “Autoselect
OFF” to off the Autoselect function.

Radio Channels / Stations Saving / Recall

You can save 4 favorite channels when you press one of the memory keys (M1, M2, M3,
M4) in DAB / FM mode.
Press “Band “ switch to FM model , can memory M1,M2,M3,M4, too.
When you selected a channel then press M1 and hold it about 2 seconds, the LCD screen
will be showed the “Preset M1 stored” on the screen and this channel is saved in M1. Next
time, you can press M1 to jump to M1 channel directly. (M2~4 setup procedure is same as
above.)

Play / Recall the Preset Radio Channels / Stations

14

If you already preset one channel in one of the preset keys (M1 ~ M4), then you can press
the correspond preset to listen the channel. E.g.: if you have saved Radio 1 in preset 2
(M2), you just need to press “M2” key to function it. The screen will be showed the “preset
# empty”.

Display modes

Press「Display」button then the screen will be showed the display modes as follows:

DLS (SCROLLING TEXT)

PROGRAMME TYPE

SIGNAL STRENGTH

(

訊號強度

)

TIME AND DATE (時間與日期)

ENSEMBLE (GROUP NAME)

(ENSEMBLE)

DLS (Dynamic Letter Show)

DLS is a scrolling text including the information transmission with the channel / program.
The information normally is included the relative data of the program.

Programme type

Display the music “style” as ”Rock” or ”Classical”.

Ensemble / Multiplex (Group Name)

Multiplex / Ensemble is an integral broadcasting radio station and transmitted via one
frequency. It has national and local radio station. The local radio station is included the
local specified station as MXR West Midlands.

Signal strength

15

The moving blocks are indicated the strength of the receiving signal. The square blocks are
closer to the right side that the signal is more strength.

MINIMUM SIGNAL LEVEL

The receiving quality will be not so good if the signal strength is less than 5 blocks
(minimum signal level).

Date & Time

The radio stations are normally provided the information of the date and time automatically ,
so you do not need to set the date and time by manual. Under the rare situation, the
stations are transmitted without any information of the date and time, then the screen will
be showed <Time/date >.

CLOCK DATE

Auto tune modes

There are two autotune modes. One is fast scan, another is fully Scan. Fast scan is only
search the digital radio band III in UK, and fully scan search for all of the digital radio
stations in frequency band III.

Fast scan, please press「Autotune」button. If you want to do the fully scan, then press the
「Autotune」button and hold about 2 seconds.

Secondary service

In some case, you can see a symbol “>” behind the radio station name. That mean is the
secondary service with this station, including other services related to the main station. E.g.,

16

the sports station might add the extra live report.
Secondary service is attached to the main station directly.

Manual tune

You can search the station in manual except the autotune. It is used to add the channel
that can not be searched after the antenna adjusted or new radio stations additional by
autotune.
Press 「Manual」, then the LCD will be showed the ”Manual tune” on the screen. Use「＋」
or「－」Up/Down button to switch the frequency from 5A to 13F channels by terms in DAB
band.

DAB CHANNELS

When ADR – 605R is found someone ensemble / multiplex in DAB band, then it will be

Please press「Enter」button to enter the present ensemble / multiplex.

On the LCD screen, the upper line is showed the first radio station / channel in this

If you want to know about the ensemble / multiplex station, press「＋」or「－」 up/down

ultiplex, it will be

leave the ”Manual tune” mode if you want.

showed on the LCD screen underline.

ensemble / multiplex.

button to find out the station which you want to listen and press「Enter」.
When you searched to the last radio station / channel for this ensemble / m
gone back to the fist one.

Press 「Enter」 button to

FM Mode

Switch DAB to FM

If you want to switch the mode from DAB to FM, just press 「Band」 button once. On the

17

e name of the present station or the frequency when

screen will be showed the “wait……”, “Switching to FM “, the ADR – 605R will be auto
selected the nearest radio station.

Wait……….

The screen upper line is showed th
RDS disable.

97.40MHz FM

Autotune

or searching for the FM stations, press 「Autotune」 to search the near frequency band.

F
When you press 「Autotune」 and hold about 2 seconds, it will be searched the frequency
band slowly. The searching will be stopped after the station was found. If you can not find
any station, the searching will be stopped after scan the all FM band from 87.5 – 108MHz.

Presets

hen you find out a station that you want to save as a preset station, just press one of the

empty” is showed on the screen if the preset button has not saved any

W
preset buttons M1 ~ M4 and hold it about 2 seconds. You can see the “Preset # stored” on
the LCD screen. Then press one of the preset buttons, you can enjoy the station which has
been preset.
The “preset #
station.

Display modes

18

Press「Display」button then you can see the information as follows:

RADIOTEXT

PROGRAMME TYPE

SIGNAL STRENGTH

AUDIO MODE

TIME AND DATE

FREQUENCY

Frequency

It will be showed the frequency of the present station as 89.30 MHZ.

Audio mode

Under FM mode, you can see the sound effect is (mono) or (stereo) on the screen.

 The radio can be switched automatically about the sound effect “mono” or “stereo”. You

can ignore this function. It would be very helpful for raising the sound quality with bad
signal strength by switching “mono” or “stereo” manually. Just press 「Enter」 button can

achieve that function.

CD Mode

CD Play

19

If you want to play the music CD disc, please press the “CD mode” button as follows
picture.

Or press the button on the remote as follows picture.

You can see the ”Switching to CD” on the LCD screen. Then you can start operate the CD
function after switched to the CD mode.
Press 「Eject」 key to open the tray and put a CD disc on it before playing the music CD.
Press 「Eject」 again to insert the disc into this device. When the LCD is showed
out ”Ready”, press 「Play」 to start the disc playing.
The CD operation other buttons as follows beside the 「Play」.

「Stop 」 -- It is used to stop play.
「Vol+ / Vol-」 Volume controller -- to control the analog audio output level.
「Next/FF」 When the CD playing, press this key that you can jump to the next track. If you

press and hold this button over 2 seconds, then it will do the fast forward.

「Prev/FR」 When the CD playing, press this key that you can jump to the previous track. If

you press and hold this button over 2 seconds, then it will do the fast rewind.

「Mute」 -- to stop the audio output.
「Repeat」 The repeat key has 5 playing modes. It will be switched the playing modes as

follows sequence when press it time by time. “NORMAL”, “SINGLE”, “REPEAT ONE”,
“REPEAT ALL”, and “RANDOM”.

CD Recording

ADR – 605R has two kinds of the recording mode. One is recording from DAB / FM radio;
another is recording from the external audio source. The detail description of operation is

20

following:

Recording from DAB/FM Radio

1. Press「Band」 to switch the system to DAB or FM mode.

2. Choose your favorite, good receive / listen effect radio station that you want to listen.

3. Press 「Eject」 key and put a blank disc or a CD-R/RW disc which has not been fully
recorded and not finalized into this device.

4. Press 「REC」 , then you can record the present radio station output audio into the

CD disc.

5. Press 「Stop」 to stop the recording and edit the just recorded disc to be an audio

track. At the same time, you can enjoy the radio continuously without interruption.

6. If you want to listen the recorded audio, press 「CD」 key to switch the system

mode to CD and wait the ”Ready” on the LDC screen. Now you can press 「Play」
to play the CD, and you also can press 「Next / FF」 or 「Prev / FR」 to listen other
audio tracks which has recorded in the previous times.

7. In process of recording, the recording will not be stopped if you choose other stations.

But the recording will be stopped if you switch the system to other modes as DAB, FM
or CD.

8. The recording will be stopped automatically when the CD-R/RW disc is full.

9. You must press the 「Finalize」 to close the disc when you finish the recording or disc
is full. The Finalize will be take about 1~1.5 minutes. After the 「Finalize」, this disc
can be played in any devices as CD, VCD or DVD player.

10. After the 「Finalize」, the CD-R disc can not be recorded any more.

11. Without function the 「Finalize」, the recorded disc just can be played in this device.

12. After 「Finalize」, the recorded CD-RW disc should be totally erased by pressing

「Erase」button and then it can do the recording again.

Recording from External Audio Source

1. Confirm the external audio source has well connected with this device first as follows:

CD Player

TV

DVD Player

Cassette Player

21

2. Press 「CD」 button to switch the system mode to CD. Now you can enjoy the audio from

the external audio source.

3. Press 「Eject」 key and put a blank disc or a CD-R/RW disc which has not been fully

recorded and not finalized into this device.

4. Press 「REC」 , then you can record the external audio into the CD disc.

5. Press 「Stop」 to stop the recording and edit the just recorded disc to be an audio track.

At the same time, you can enjoy the radio continuously without interruption.

6. By pressing 「Play」 and 「Stop」 keys time by time, you can make an personal favorite

effect of multi tracks audio CD.

7. If you want to listen the recorded audio, press 「CD」 key to switch the system mode to

CD and wait the ”Ready” on the LDC screen. Now you can press 「Play」 to play the
CD, and you also can press 「Next / FF」 or 「Prev / FR」 to listen other audio tracks
which has recorded in the previous times.

8. In process of recording, the recording will be stopped if you switch the system to other

modes as DAB, FM or CD.

9. The recording will be stopped automatically when the CD-R/RW disc is full.

10. You must press the 「Finalize」 to close the disc when you finish the recording or disc

is full. The Finalize will be take about 1~1.5 minutes. After the 「Finalize」, this disc can
be played in any devices as CD, VCD or DVD player.

1 1. After the 「Finalize」, the CD-R disc can not be recorded any more.

12. Without function the 「Finalize」, the recorded disc just can be played in this device.

13. After 「Finalize」, the recorded CD-RW disc should be totally erased by pressing「Erase」

button and then it can do the recording again.

Erase Disc

Press 「Erase」 key to erase the recorded disc for new recording purpose. There are two
kinds of the erase as follows.

(1) If you press the 「Erase」 key then you erase the last track only. This is available

when the CD-RW disc has not been finalized.

(2) If you press and hold the 「Erase」 key over 2 seconds, then you can erase the

entire disc material.

(3) You should switch the system to the CD mode before pressing / function 「Erase」.
(4) Make sure that the CD-RW disc was inserted into the device. Recheck the disc’s

material before you do the erase because the erasing can not be stopped / pause.

(5) The 「Erase」 timing is depended on the size of the recorded material. Generally it

will be took about 1 ~ 1.5 minutes.

Check Lists of the Recording not function

22

1. Check the disc was put into the device correctly.

2. Check the disc is CD- R, CD-RW.

3. Check the disc still has the space to record or full.

4. Check the disc has been finalized or not.

5. Please put the disc in the central of tray and try it again if the above issues are none.

6. Do not use the CD-R / RW disc that is scratch seriously, dirty, or poor quality.

23

Others setting

Alarm Setting

You can set the alarm both in standby or power on mode. Press「Sleep」and hold it about
2 seconds to setup the alarm while the power on. You can see the messages on the LCD

screen as follows about 5 – 6 seconds. The <OFF> / <ON> is flashing, you should press
「＋」、「－」Up / Down keys to switch ON / OFF and press 「Enter」 key in 5 – 6 seconds.

After you setup the alarm ON / OFF and ENTER, the flashing sign will be jumped to hour
position. Also you should press 「＋」、「－」Up / Down keys to setup the hour and then

ENTER. The flashing sign will be jumped to the next minute and you can setup the number
of minute too as above the hour setting. Press 「Enter」 button time by time, the process

will be took term to next one.

ALARM
<OFF> 12:00

ALARM

<ON> 00:00

ALARM
<ON> 12:00

Press「Sleep」 to setup the alarm while the power standby . You can see the USER CLOCK
/ ALARM switching on the LCD screen when you press 「Sleep」 time by time. When the
ALARM on the screen and the <OFF> / <ON> is flashing, you should press 「＋」、「－」
Up / Down keys to switch ON / OFF and press 「Enter」 key in 5 – 6 seconds. After you
setup the alarm ON / OFF and ENTER, the flashing sign will be jumped to hour position.

Also you should press 「＋」、「－」Up / Down keys to setup the hour and then ENTER. The
flashing sign will be jumped to the next minute and you can setup the number of minute too

as above the hour setting.

ALARM

<ON> 00:01

Every time you press the 「＋」、「－」buttons, the time only change one number. If you want
to change it faster, then keep pressing「＋」、「－」buttons. Every time you complete the time

24

setting, press「Enter」button to confirm it. If you want to leave the time setting, keep free the
buttons on the remote about 5 – 6 seconds later then it will be back to the original mode.

When you completed the alarm setting, make sure the volume is enough or not. If you want
to active alarm, press the “Standby ” button to switch the radio to standby mode. If you
want to set off the alarm, press 「Sleep」 and hold it over 2 seconds then set it off and see
the “alarm status off” on the LCD screen. If you want to leave the time setting, keep free
the buttons on the remote about 5 – 6 seconds later then it will be back to the original
mode.

Sleep mode

This function can be used to set this device power off (standby) automatically in the certain
time. Press「Sleep」button then you can see message in below. Every time press「Sleep」

button, the timing to sleep is from 90 minutes gradually down to 10 minutes. If you set it to
be 0 minutes means setting off the sleep mode.

<80>
..
<0>

<90>

Sleep

User Clock Setting

You can setup the user clock at the standby mode. Press「Sleep」, you can see the USER
CLOCK / ALARM switching on the LCD screen when you press 「Sleep」 time by time. You
can see the messages on the LCD screen as follows about 5 – 6 seconds.

USER CLOCK
0:00:01

The Time <0:00:01> is flashing, you should press ENTER to switch the flashing to hour
location and press 「＋」、「－」 Up / Down keys to setup the hour and press 「Enter」 key

in 5 – 6 seconds. After you setup the hour and ENTER, the flashing sign will be jumped to
the minute position. Also you should press 「＋」、「－」 Up / Down keys to setup the minute

and then ENTER. The flashing sign will be jumped to the next second and you can setup
the number of minute too as above setting. Press 「Enter」, to finish the setting.

25

8. Cautions and Maintenance

y

Please avoid the device exposing under the sunlight directly, high temperatures, high

◎ th electronic

◎ t this device with other hard-cover objects to avoid scratching. You can use

◎ ic electric charge

◎ se seek the help from the dealer always

◎ signal cable hardly. Always unplug and pull to hold the plug

This ADR – 605R is extremely precision audio equipment, so please according to the
following instructions to ensure the best preservation and avoid the unnecessary safet
issues.

◎

humidity environment and heat. Also, please keep out of reach of children.
Please keep the metal terminals cleaning and please use the cotton bars wi
detergent to clean it if it is dirty. Make sure that no cotton fibers are left inside the
terminals.
Prevent pu
the soft clothes with little neutral detergent or Isopropyl alcohol to wipe the dirty cover
gently. Avoid using alcohol for cleaning to prevent damaging surface.
Unplug the device’s power cable during the lightning. Release the stat
when it is stored under the dry environment.
DO NOT try to fix this device by yourself. Plea
the device is out of order.
DO NOT pull the power or
head not cable. Avoid curling the cable too much when storage them.

9. Troubleshooting Guide Line

hen ADR – 605R is out of order, please check the following table first before sending it

W
back for repairing.

Problems Causes Troubleshooting

26

No po ght

Bad AC power connect Check power cable & power source

wer, LCD no li
on
On DAB model, press

Bad signal

“ Autoscan” no signal

Move antenna to other location then
“Autoscan“ again.

Moved antenna , but still

No DAB service.

gitalradionow.com/

No DAB signal

Please visit

http://www.di to

check the DAB broadcast information

in your area.

When received DAB

t Bad signal

D screen display the

n

e

signal, audio signal no
continue with noise.

Check the LC
signal strength (over 5 blocks is
better), if lower than 4 blocks the
change the antenna location or clos
the house window.

On FM mode has noise. Bad signal

en switch to

ed

If FM signal weak th
“Mono” model (Check FM Audio
model). On FM model “Stereo” ne
stronger signal than “Mono”.

No sound output when Too low level of volume is

by. the alarm is on output

Make sure the volume output
enough before power off to stand

No audio signal output,

The station provide data only

as NTL station only
provide data without
music

Some stations provide data only. In
the future they might start providing
the services as information of stock

market, news, and music.
CD Tray can not open /
close

Disc put on the wrong
position

Put / adjust the CD disc position

again.

Forward / Rewind CD Play” back to normal speed. Press “
Audio output poor connect Check the Audio connect & cable
Amplifier / TV volume is
controlled too small

Please tune the volume bigger

Setup too small the audio

Please check the audio output setting

output

No Sound

on “Mute” “Mute“ off

No batteries / batteries

ng.

ries /replace new

power poor / liquid leaki

Put in batte

batteries.
Remote Control fail

tteries in correct position /

Batteries wrong position

Put the ba

direction.

Poor disc quality Replace new CD-R/RW disc
Disc put up-side-down Turn to right side of CD Disc

No disc

Disc dirty Clean the CD Disc

27

rted Format Disc

.

Not suppo
(DVD / CD-ROM / VCD…)

Put the supported Audio CD disc only

None of above problems Put the disc correctly and insert again
Record CD-R/RW noise /
Can not be recorded

CD-R / RW Finalized, Not

blank CD-R/RW disc, bad

quality.

Change new CD-R / RW disc

Record only one channel

Audio cable just connect one

channel or audio source only

one channel

Make sure the Audio cable connect
well.

The recorded sound
effect is bad

Audio source is unstable

Use amplifier to increase the signal

level
Unstable in CD playing
and recording process

The best operation
environment is 25℃

Put the device in good environment

10. Specification

music CD

This unit is a multi functional audio system. It can receive DAB, FM radio, play music CD
and recording audio CD from DAB / FM or external audio source (ADR-605R).
This device has excellent readability. It can playback various discs, also records
by using CD-R, CD-RW discs.

28

Key Features

 Fully Integrated DAB / FM + CD Player / CD Recorder















 DAB Service Selectio











Accessories Supplied: Remote control, Audio Cable, AC Cable, Optical Cable, Antenna,

CD Sound quality without background noise for both DAB and CD system
CD Playback and CD Recording from either DAB / FM or external Audio source
DAB band III / L Band with FM band II (include Canada L Band)
Keyboard / LCD direct connection
Single DAB / FM antenna connector
Superior RF Receiver Sensitivity
Frequency range: DAB VHF Band III 174 MHz – 240 MHz

L-Band 1452 MHZ – 1492 MHZ
FM 87.5MHz – 108MHz

n
DAB Ensemble Automatic tune & Memory
FM frequency tune & Auto tune
4-Presets Memory (DAB / FM)
S / PDIF optical output
IR Remote Control

User Manual

Specification

r Condition Min Typical Max Unit Paramete

DAB

RF frequency range Band III 174 240 MHz

L-Band 1452 1492 MHZ

Sensitivity VHF ent -9 Measurem

to EN50248 [3]

-96 8 dBm

29

Maximum Input Signal for a -10dBm 0 dBm

BER of 10-4

VHF

Adjace lectivity: 32 35 dB nt Channel Se

(EN50248)

F ivity. 45 55 dB ar-off select

(EN50248)

Acqui ivity -102 dBm sition Sensit

FM

RF Frequency Range 87.5 108 MHz

RF Sensitivity (S+N)/N dB = 26 2 uV
RF ity 0.5 Limiting Sensitiv uV
Large Signal Handling

capacity

500 mV

(S+N)/N Ultimate signal to 38 dB

noise ratio

THD 0.5 % @200mV

Environment & Physical

Operating Temperature

Range

5 45 ∘ C

Storage T ure Range -20 70 ∘C emperat

Storage Humidity Relative umidity 90 H %

CD Player / Recorder

Playable Discs CD / CD-R /

CD-RW

Recordable Discs CD-R / CD-RW

F 20 20 KHz requency Response

S/N Ratio 80 dB

D r 44.1 KHz /A Converte

16 bit

Digital Output

Audio O/P Digital oaxial Unit C 1

Digital Optical 1 Unit
Analog 2CH 1 Set

Other

Audio I/P Analog 2CH 1 Set

In A , put Power C 1 10V~240V

50~60Hz

Consumption 35W

Dimensions L332*W H60m430*

m

Weight 4.8kg

※Products specifications and design subject to change without notice.※

Meicheng

®

MEI CHENG AUDIO VIDEO CO., LTD

Address: 5F., NO.111, SEC. 2, HUAN HO N. RD., TAIPEI, 10376 TAIWAN

Tel: [phone], Fax: [phone]
Website: www.meicheng.com.tw Email: [e-mail]