Wireless digital PIR detector User Manual
1.Introduction
MC-5 35R is a PI R in trude r detecto r for ind oo r use.I t adopt s
prec ision c yl indri cal FRE SN EL len s, can effect ively i mprove
ener gy savi ng , with hi gh sensit ivity a nd f ree of fa lse ala rm . By
usin g advan ce d paten ted softw are, it c an i denti fy the re al
intr uder an d ot her int erferen ce fact or w hich ma y resul t in f alse
alar m. Puls e co untin g can be ad ju stabl e. It is wide ly use in
vari ous ind oo r appli catio ns , Built -in big cap acity l ithium
batt ery, po wer-s ave mod e. Its wor king li fe i s up to 2 yea rs or
abov e.
Fig. 1 Appearanc e
PIR
LED
Fig. 2 Inter nal S truct ure
Batt ery conta iner
Tamper switch
DIP swi tc h
2.Specifications
Model:MC-535R
Maximum detection distance: 12m/25
Emitting distance: 120m (in the open area)
Infrared distance:
Working voltage: DC3V, 1*CR123A lithium battery
Alarm current: ＜20mA
Quiescent Current: 16µA~17µA
Infrared section (as shown at right)
Optical lens data sheet
Infrared area: 12 × 4 (typical)
Maximum coverage: 12m * 12m (39 * 39 feet) / 90 °
Emitting distance : 433MHz
Alarm indication: The LED indicator is on for 2~3 seconds.
12m
℃
9m
6m
3m
0
3m
6m
9m
0
Wal l mo un ti ng w id e
angle lens v ie w
,
7.5
,
5
,
2
,
0
3.Installation
3.1 Notes
X
Don' t face co ld o r
heat d irect ly
Don' t face th e su n
-shi ne dire ct ly
X
8m
4m
,
8
4m
Side view
Don' t insta ll n ear
elec tric ca bl es
12m
,
2316
8m
12m
,
X
Installation：
①wide-angle: 12M * 12M detection angle of 110 degrees
②flat curtain: 12M * 2M detection angle of 3 de gr ee s
③ceiling curtain: 6M * 1M detection angle of 3 de gr ee s
④ ： 2~2.3M
Installation height
Operation condition:
Operation temperature:-
2.3m
1.5m
S
torage temperature:20℃ ~60℃( 4℉ ~1 40℉)
0.6m
Size:：86(L)*45(W)*36(H)mm
10℃~60℃ ﹤95%RH
X
Don' t insta ll o n a
unst able ba se
Don' t face me ta l wall
X
3.2 Installation location
Use do uble- si ded adh esive t o in stall t he detect or 2 to 2.3 m et ers
from t he grou nd , pay att en tion to t he inst al latio n of PIR down .
In s tal lati on can c hoos e to ins tall w ide- ang l e, fl a t
cu rtai n, cei lin g c urt ain th ree wa y s, di ffe rent i nsta lla t ion
me thod s corr esp ondi ng to th e i nst a lla tio n h eig h t and
de tect ion an gle is d iff eren t (see " 2, spe cifi cat ions a n d
te chni cal pa ram eter s") .
3.3 Change ba ttery:
A, wit h a word sc re wdriv er
ligh t top gro ov e, pull o ut the
bott om cover, re move th e
bott om cover.
P/N: 20170 42 8A01
Dete ctor
2~2 .3m
B, rem ove the o ld b atter y, ac co rding t o the mar ke d polar ity of the
batt ery corre ctly in to t he batt ery.
+
+
-
-1-
C, the s ide of th e sh ell wit h a battery u p one end , th e botto m cover
with a b utton at on e end dow n th e face of t he shel l to c lose an d
pull t he bottom c over in to t he face s hell.
4. DIP switch function description
Swit ch seri al
numb er
1
2
3
High s ensit iv ity(de fault)
Alar m delay 5 s ec ond
LED is o ff
OFF ON
Low se nsiti vi ty
Alar m delay 5 m in utes( d efault)
LED is o n(defa ul t)
5. Coding method between detector and panel:
Codi ng sett in g:
①Set th e detec to r as norm al mode, pl ace the b at tery an d LED wil l fl ash
seco nds,s et t he pane l as coding m ode(p anel codi ng sett in g pls ref er
to pan el manu al ), with in 3 second s when pr ess the con firm ke y of t he pane l
Wav e hand ne ar t he fron t side of d et ector, i t wi ll send a a larm si gn al
to the p anel, if th e panel s ounds a res ponse t he n code su ccess fu lly.
②Ente r the add re ss numb er to code wi th pane l,set the p anel as m an ual cod ing
mode a nd ente r th e 9-dig it addres s numbe r,this met hod is mu ch b etter.
6. Walking test in coverage area:
①Set th e detec to r as test m od e to proc eed wal k- test.
②Wal k acc ros s the f ar ed ge of coverage area at the sp eed o f 1st ep/ second
(about 0.75m/s) . The LED will f las h for s eco nds then alarm(see the right f igu re) .
③Do walk-test in opp osi te di rec tion to confirm the bound ary o f bot h sid es.Make
sure the detectio n cen tre p oin ting to the centre of pr ote cte d are a.
④Make sure the detec tio n cen tre a t the proper place,shou ld pr ope rly a dju st the
detection area if y ou ca n not g et an i deal detection area.
⑤After adjust the de tec tio n ang le, should re-do walk tes t as ab ove .
⑥After pass in g th e te st , be s ure to set the alarm dela y to 5 m in ut es m ode, otherwise it wil l
aff ect the battery life。
ON KE
1 2 3
Tamper switch
7. Customer Se rvice
For any help please c ont act w ith o ur company and you could visit o ur we bsi te fo r more information
FC C WARNI NG
Changes or modifi cat ion s not e xpressly approved by the par ty re spo nsi ble for compliance coul d voi d the u ser 's au thority
to operate the equi pme nt.
This e quipm en t has bee n tested an d found t o co mply wi th the li mi ts for a Cl ass B digit al devi ce , pursu ant to Pa rt 1 5 of the FC C Rules.
Thes e limit s ar e desig ned to prov ide rea sonable p rotec ti on agai nst har mf ul inte rfere nc e in a resi denti al i nstal lation. Thi s equip me nt
gene rates u se s and can r adiat e ra dio fre quency en ergy an d, if not ins talle d an d used in a ccord an ce with t he inst ru ction s, may caus e
harm ful int er feren ce to radio c ommun ication s.
Howe ver, the re i s no guar antee tha t inter fe rence w ill not o cc ur in a particular installation. If this equi pment does cause harmful inte rference
to rad io or tel ev ision r eceptio n, whic h can be dete rmine d by t urnin g the equ ip ment off an d on, the use r is enco ur aged to t ry to cor re ct the
inte rfere nc e by one or m ore of the fo llowi ng m easur es:
-- Reo rient o r re locat e the recei ving an te nna.
-- Inc rease t he s epara tion betw een the e qu ipmen t and rec ei ver.
-- Con nect th e eq uipme nt into an ou tlet on a c ir cuit di ff erent fro m that to w hi ch the re ceive r is c onnec ted.
-- Con sult th e de aler or a n exper ie nced ra dio/TV te chnic ian for hel p .
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
-2-
Loading...