D163, Tyre & Trim Detailer (24-47A): D16332
__________________________________________________________________________________________
Page: 1 of 14
Safety Data Sheet
Copyright, 2014, Meguiar's, Inc. All rights reserved. Copying and/or downloading of this information for the purpose of
properly utilising Meguiar's, Inc. products is allowed provided that: (1) the information is copied in full with no changes
unless prior written agreement is obtained from Meguiar's, Inc., and (2) neither the copy nor the original is resold or otherwise
distributed with the intention of earning a profit thereon.
Document group:
30-1896-7
Version number:
2.00
Revision date:
23/04/2014
Supersedes date:
10/09/2012
Transportation version number: 1.00 (10/09/2012)
This Safety Data Sheet has been prepared in accordance with the REACH Regulation (EC) 1907/2006 and its modifications.
SECTION 1: Identification of the substance/mixture and of the
company/undertaking
1.1. Product identifier
D163, Tyre & Trim Detailer (24-47A): D16332
1.2. Relevant identified uses of the substance or mixture and uses advised against
Identified uses
Automotive.
1.3. Details of the supplier of the substance or mixture
Address:
Meguiars United Kingdom Limited, 3 Lamport Court, Heartlands, Daventry, Northants, NN11 8UF
Telephone:
+44 (0)870 241 6696
E Mail:
info@meguiars.co.uk
Website:
www.meguiars.co.uk
1.4. Emergency telephone number
+44 (0)870 241 6696
SECTION 2: Hazard identification
2.1. Classification of the substance or mixture
CLP REGULATION (EC) No 1272/2008
CLASSIFICATION:
This material is not classified as hazardous according to Regulation (EC) No. 1272/2008, as amended, on classification,
labelling, and packaging of substances and mixtures.
Dangerous substances(67/548/EEC)/preparations(1999/45/EC) directive
This product is not classified as hazardous according to EU Directive 1999/45/EC.
2.2. Label elements
CLP REGULATION (EC) No 1272/2008
Not applicable
D163, Tyre & Trim Detailer (24-47A): D16332
__________________________________________________________________________________________
Page: 2 of 14
SUPPLEMENTAL INFORMATION
Supplemental Hazard Statements:
EUH210 Safety data sheet available on request.
EUH208 Contains Mixture of 5-chloro-2-methyl-2H-isothiazol-3-one and 2-methyl-2H-
isothiazol-3-one. May produce an allergic reaction.
Notes on labelling
Updated per Regulation (EC) No. 648/2004 on detergents.
Ingredients required per 648/2004: 5-15%: Aliphatic hydrocarbons. <5%: Non-ionic surfactant. Contains: Perfumes, Mixture
of Methylchloroisothiazolinone and Methylisothiazolinone (3:1).
Dangerous substances(67/548/EEC)/preparations(1999/45/EC) directive
Not applicable
Notes on labelling
Updated per Regulation (EC) 648/2004 on detergents.
Ingredients required per 648/2004: 5-15%: Aliphatic hydrocarbons. <5%: Non-ionic surfactant. Contains: Perfumes, Mixture
of Methylchloroisothiazolinone and Methylisothiazolinone (3:1).
2.3. Other hazards
None known.
SECTION 3: Composition/information on ingredients
Ingredient CAS Nbr EU Inventory % by Wt Classification
Siloxanes and silicones, di-Me 63148-62-9 30 - 60
Non-Hazardous Ingredients Mixture 30 - 60
Distillates (petroleum), hydrotreated light 64742-47-8 EINECS 265-
149-8
5 - 10 Xn:R65 - Nota 4 (EU)
R10; R66; R67 (Self Classified)
Asp. Tox. 1, H304 (CLP)
Flam. Liq. 3, H226; STOT SE 3,
H336; EUH066 (Self Classified)
Conditioners Trade Secret < 5
Bis(2-ethylhexyl) adipate 103-23-1 EINECS 203-
090-1
0.1 - 1.0 N:R50 (Self Classified)
Aquatic Acute 1, H400,M=1;
Aquatic Chronic 2, H411 (Self
Classified)
Triethanolamine 102-71-6 EINECS 203-
049-8
0.1 - 1
Mixture of 5-chloro-2-methyl-2Hisothiazol-3-one and 2-methyl-2Hisothiazol-3-one
55965-84-9 < 0.001 T:R23-24-25; C:R34; N:R50/53;
R43 (EU)
Acute Tox. 3, H331; Acute Tox.
3, H311; Acute Tox. 3, H301;
Skin Corr. 1B, H314; Skin Sens.
1A, H317; Aquatic Acute 1,
H400,M=10; Aquatic Chronic 1,
H410,M=10 (CLP)
Please see section 16 for the full text of any R phrases and H statements referred to in this section
Please refer to section 15 for the any applicable Notas that have been applied to the above components
D163, Tyre & Trim Detailer (24-47A): D16332
__________________________________________________________________________________________
Page: 3 of 14
For information on ingredient occupational exposure limits or PBT or vPvB status, see sections 8 and 12 of this SDS
SECTION 4: First aid measures
4.1. Description of first aid measures
Inhalation
Remove person to fresh air. If you feel unwell, get medical attention.
Skin contact
Wash with soap and water. If signs/symptoms develop, get medical attention.
Eye contact
Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get
medical attention.
If swallowed
Rinse mouth. If you feel unwell, get medical attention.
4.2. Most important symptoms and effects, both acute and delayed
See Section 11.1 Information on toxicological effects
4.3. Indication of any immediate medical attention and special treatment required
Not applicable
SECTION 5: Fire-fighting measures
5.1. Extinguishing media
In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.
5.2. Special hazards arising from the substance or mixture
None inherent in this product.
Hazardous Decomposition or By-Products
Substance Condition
Carbon monoxide. During combustion.
Carbon dioxide. During combustion.
5.3. Advice for fire-fighters
No unusual fire or explosion hazards are anticipated.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Ventilate the area with fresh air. Observe precautions from other sections.
6.2. Environmental precautions
Avoid release to the environment. For larger spills, cover drains and build dykes to prevent entry into sewer systems or
bodies of water.
6.3. Methods and material for containment and cleaning up
Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially
D163, Tyre & Trim Detailer (24-47A): D16332
__________________________________________________________________________________________
Page: 4 of 14
available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent
material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible.
Place in a closed container approved for transportation by appropriate authorities. Clean up residue with detergent and water.
Seal the container. Dispose of collected material as soon as possible.
6.4. Reference to other sections
Refer to Section 8 and Section 13 for more information
SECTION 7: Handling and storage
7.1. Precautions for safe handling
Keep out of reach of children. Avoid breathing dust/fume/gas/mist/vapours/spray. Do not eat, drink or smoke when using
this product. Wash thoroughly after handling. Avoid contact with oxidising agents (eg. chlorine, chromic acid etc.)
7.2. Conditions for safe storage including any incompatibilities
Store away from heat. Store away from acids. Store away from oxidising agents.
7.3. Specific end use(s)
See information in Section 7.1 and 7.2 for handling and storage recommendations. See Section 8 for exposure controls and
personal protection recommendations.
SECTION 8: Exposure controls/personal protection
8.1 Control parameters
Occupational exposure limits
No occupational exposure limit values exist for any of the components listed in Section 3 of this Safety Data Sheet.
Biological limit values
No biological limit values exist for any of the components listed in Section 3 of this safety data sheet.
8.2. Exposure controls
8.2.1. Engineering controls
Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure
Limits and/or control dust/fume/gas/mist/vapours/spray. If ventilation is not adequate, use respiratory protection equipment.
8.2.2. Personal protective equipment (PPE)
Eye/face protection
Eye protection not required.
Skin/hand protection
No chemical protective gloves are required.
Respiratory protection
An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of
a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator
type(s) to reduce inhalation exposure:
Half facepiece or full facepiece air-purifying respirator suitable for organic vapours and particulates
D163, Tyre & Trim Detailer (24-47A): D16332
__________________________________________________________________________________________
Page: 5 of 14
For questions about suitability for a specific application, consult with your respirator manufacturer.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state
Liquid.
Appearance/Odour
Creamy white liquid. Blueberry odour.
Odour threshold
No data available.
pH
8 - 8.5
Boiling point/boiling range
100 ºC
Melting point
No data available.
Flammability (solid, gas)
Not applicable.
Explosive properties
Not classified
Oxidising properties
Not classified
Flash point
Flash point > 93 °C (200 °F)
Autoignition temperature
No data available.
Flammable Limits(LEL)
No data available.
Flammable Limits(UEL)
No data available.
Vapour pressure
No data available.
Relative density
1 [Ref Std:WATER=1]
Water solubility
Moderate
Solubility- non-water
No data available.
Partition coefficient: n-octanol/water
No data available.
Evaporation rate
No data available.
Vapour density
No data available.
Decomposition temperature
No data available.
Viscosity
18 Pa-s
Density
1 g/ml
9.2. Other information
Volatile organic compounds (VOC)
0 %
VOC less H2O & exempt solvents
0 g/l
SECTION 10: Stability and reactivity
10.1 Reactivity
This material is considered to be non reactive under normal use conditions
10.2 Chemical stability
Stable.
10.3 Possibility of hazardous reactions
Hazardous polymerisation will not occur.
10.4 Conditions to avoid
Heat.
10.5 Incompatible materials
Loading...