MEGUIAR'S D150 User Manual

D150, X-Press Liquid Wax (21-133A), D15001

__________________________________________________________________________________________

Page: 1 of 15

Safety Data Sheet

Copyright, 2014, Meguiar's, Inc. All rights reserved. Copying and/or downloading of this information for the purpose of
properly utilising Meguiar's, Inc. products is allowed provided that: (1) the information is copied in full with no changes
unless prior written agreement is obtained from Meguiar's, Inc., and (2) neither the copy nor the original is resold or otherwise
distributed with the intention of earning a profit thereon.

Document group:

26-6703-8

Version number:

2.00

Revision date:

16/04/2014

Supersedes date:

23/07/2012

Transportation version number: 1.00 (25/07/2011)

This Safety Data Sheet has been prepared in accordance with the REACH Regulation (EC) 1907/2006 and its modifications.

SECTION 1: Identification of the substance/mixture and of the
company/undertaking

1.1. Product identifier

D150, X-Press Liquid Wax (21-133A), D15001

1.2. Relevant identified uses of the substance or mixture and uses advised against

Identified uses

Automotive.

1.3. Details of the supplier of the substance or mixture
Address:

Meguiars United Kingdom Limited, 3 Lamport Court, Heartlands, Daventry, Northants, NN11 8UF

Telephone:

[phone]

E Mail:

[e-mail]

Website:

www.meguiars.co.uk

1.4. Emergency telephone number

[phone]

SECTION 2: Hazard identification

2.1. Classification of the substance or mixture

CLP REGULATION (EC) No 1272/2008

CLASSIFICATION:

Skin Corrosion/Irritation, Category 2 - Skin Irrit. 2; H315

For full text of H phrases, see Section 16.

Dangerous substances(67/548/EEC)/preparations(1999/45/EC) directive

This product is not classified as hazardous according to EU Directive 1999/45/EC.

2.2. Label elements

CLP REGULATION (EC) No 1272/2008

D150, X-Press Liquid Wax (21-133A), D15001

__________________________________________________________________________________________

Page: 2 of 15

SIGNAL WORD

WARNING!

Symbols:

GHS07 (Exclamation mark) |

Pictograms

HAZARD STATEMENTS:

H315 Causes skin irritation.

PRECAUTIONARY STATEMENTS
General:

P102 Keep out of reach of children.
P101 If medical advice is needed, have product container or label at hand.

Prevention:

P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P262 Do not get in eyes, on skin, or on clothing.

Response:

P302 + P352 IF ON SKIN: Wash with plenty of soap and water.
P332 + P313 If skin irritation occurs: Get medical advice/attention.
P331 Do NOT induce vomiting.
P301 + P310 IF SWALLOWED: Immediately call a POISON CENTRE or doctor/physician.

SUPPLEMENTAL INFORMATION

Supplemental Hazard Statements:

EUH208 Contains Mixture of 5-chloro-2-methyl-2H-isothiazol-3-one and 2-methyl-2H-

isothiazol-3-one. May produce an allergic reaction.

Contains 19% of components with unknown hazards to the aquatic environment.

Notes on labelling

H304 is not required on the label due to the product's viscosity
Nota P applied to CAS # 64742-48-9.

Dangerous substances(67/548/EEC)/preparations(1999/45/EC) directive

Not applicable

Notes on labelling

R65 is not required on the label due to the product's viscosity.

Nota P applied to CASRN 64742-48-9.

2.3. Other hazards

None known.

D150, X-Press Liquid Wax (21-133A), D15001

__________________________________________________________________________________________

Page: 3 of 15

SECTION 3: Composition/information on ingredients

Ingredient CAS Nbr EU Inventory % by Wt Classification

Non-Hazardous Ingredients Mixture 60 - 80
Naphtha (petroleum), hydrotreated heavy 64742-48-9 EINECS 265-

150-3

10 - 30 Xn:R65 - Nota 4,P (EU)

Xi:R38; R67 (Self Classified)

Asp. Tox. 1, H304 - Nota P
(CLP)
Skin Irrit. 2, H315; STOT SE 3,

H336 (Self Classified)
Siloxanes and silicones, di-Me 63148-62-9 1 - 5
Kaolin, calcined 92704-41-1 EINECS 296-

473-8

0.5 - 1.5

Ceramic materials and wares, chemicals 66402-68-4 EINECS 266-

340-9

0.5 - 1.5

Mixture of 5-chloro-2-methyl-2H­isothiazol-3-one and 2-methyl-2H­isothiazol-3-one

55965-84-9 < 0.001 T:R23-24-25; C:R34; N:R50/53;

R43 (EU)

Acute Tox. 3, H331; Acute Tox.

3, H311; Acute Tox. 3, H301;

Skin Corr. 1B, H314; Skin Sens.

1A, H317; Aquatic Acute 1,

H400,M=10; Aquatic Chronic 1,

H410,M=10 (CLP)

Please see section 16 for the full text of any R phrases and H statements referred to in this section
Please refer to section 15 for the any applicable Notas that have been applied to the above components

For information on ingredient occupational exposure limits or PBT or vPvB status, see sections 8 and 12 of this SDS

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation

Remove person to fresh air. If you feel unwell, get medical attention.

Skin contact

Immediately wash with soap and water. Remove contaminated clothing and wash before reuse. If signs/symptoms develop,
get medical attention.

Eye contact

Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get
medical attention.

If swallowed

Rinse mouth. If you feel unwell, get medical attention.

4.2. Most important symptoms and effects, both acute and delayed

See Section 11.1 Information on toxicological effects

4.3. Indication of any immediate medical attention and special treatment required

Not applicable

D150, X-Press Liquid Wax (21-133A), D15001

__________________________________________________________________________________________

Page: 4 of 15

SECTION 5: Fire-fighting measures

5.1. Extinguishing media

In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.

5.2. Special hazards arising from the substance or mixture

Closed containers exposed to heat from fire may build pressure and explode.

Hazardous Decomposition or By-Products

Substance Condition

Formaldehyde During combustion.
Carbon monoxide. During combustion.
Carbon dioxide. During combustion.
Irritant vapours or gases. During combustion.

5.3. Advice for fire-fighters

Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and
prevent explosive rupture.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Evacuate area. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation
to disperse or exhaust vapours, in accordance with good industrial hygiene practice. Warning: A motor could be an ignition
source and could cause flammable gases or vapours in the spill area to burn or explode. Refer to other sections of this SDS
for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment.

6.2. Environmental precautions

Avoid release to the environment.

6.3. Methods and material for containment and cleaning up

Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially
available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent
material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible.
Place in a closed container approved for transportation by appropriate authorities. Clean up residue with water. Seal the
container. Dispose of collected material as soon as possible.

6.4. Reference to other sections

Refer to Section 8 and Section 13 for more information

SECTION 7: Handling and storage

7.1. Precautions for safe handling

For industrial or professional use only. Avoid breathing dust/fume/gas/mist/vapours/spray. Do not get in eyes, on skin, or on
clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Avoid contact with oxidising
agents (eg. chlorine, chromic acid etc.)

7.2. Conditions for safe storage including any incompatibilities

Store away from heat. Store away from acids. Store away from strong bases. Store away from oxidising agents.

7.3. Specific end use(s)

See information in Section 7.1 and 7.2 for handling and storage recommendations. See Section 8 for exposure controls and
personal protection recommendations.

D150, X-Press Liquid Wax (21-133A), D15001

__________________________________________________________________________________________

Page: 5 of 15

SECTION 8: Exposure controls/personal protection

8.1 Control parameters

Occupational exposure limits

Ingredient CAS Nbr Agency Limit type Additional comments

Naphtha (petroleum),
hydrotreated heavy

64742-48-9 Manufacturer

determined

TWA:100 ppm

Health and Safety Comm. (UK) : UK Health and Safety Commission
TWA: Time-Weighted-Average
STEL: Short Term Exposure Limit
CEIL: Ceiling

Biological limit values

No biological limit values exist for any of the components listed in Section 3 of this safety data sheet.

8.2. Exposure controls

8.2.1. Engineering controls

Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure
Limits and/or control dust/fume/gas/mist/vapours/spray. If ventilation is not adequate, use respiratory protection equipment.

8.2.2. Personal protective equipment (PPE)

Eye/face protection

None required.

Skin/hand protection

Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the
results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the
substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions.
Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective
clothing.
Gloves made from the following material(s) are recommended: Nitrile rubber.
Polymer laminate

Respiratory protection

An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of
a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator
type(s) to reduce inhalation exposure:
Half facepiece or full facepiece air-purifying respirator suitable for organic vapours

For questions about suitability for a specific application, consult with your respirator manufacturer.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties
Physical state

Liquid.

Appearance/Odour

Pleasant, fruity odour; Milky white lotion

Odour threshold

No data available.

pH

9 - 9.6

Boiling point/boiling range

100 ºC

Melting point

Not applicable.