MEGUIAR'S D101 User Manual

D101, Detailer All Purpose Cleaner (DX-101A): D10101, D10105, D10155

__________________________________________________________________________________________

Page: 1 of 13

Safety Data Sheet

Copyright, 2013, Meguiar's, Inc. All rights reserved. Copying and/or downloading of this information for the purpose of
properly utilising Meguiar's, Inc. products is allowed provided that: (1) the information is copied in full with no changes
unless prior written agreement is obtained from Meguiar's, Inc., and (2) neither the copy nor the original is resold or otherwise
distributed with the intention of earning a profit thereon.

Document group:

26-8095-7

Version number:

3.00

Revision date:

01/03/2013

Supersedes date:

25/04/2012

Transportation version number: 2.00 (04/03/2013)

This Safety Data Sheet has been prepared in accordance with the REACH Regulation (EC) 1907/2006 and its modifications.

SECTION 1: Identification of the substance/mixture and of the
company/undertaking

1.1. Product identifier

D101, Detailer All Purpose Cleaner (DX-101A): D10101, D10105, D10155

Product identification numbers

KS-9990-0697-0

1.2. Relevant identified uses of the substance or mixture and uses advised against

Identified uses

Automotive.

1.3. Details of the supplier of the substance or mixture
Address:

Meguiars United Kingdon Limited, 3 Lamport Court, Heartlands, Daventry, Northants, NN11 8UF

Telephone:

[phone]

E Mail:

[e-mail]

Website:

www.meguiars.co.uk

1.4. Emergency telephone number

[phone]

SECTION 2: Hazard identification

2.1. Classification of the substance or mixture

Dangerous substances(67/548/EEC)/preparations(1999/45/EC) directive
Indication of danger

Corrosive; C; R35

For full text of R phrases, see Section 16.

2.2. Label elements

Dangerous substances(67/548/EEC)/preparations(1999/45/EC) directive

D101, Detailer All Purpose Cleaner (DX-101A): D10101, D10105, D10155

__________________________________________________________________________________________

Page: 2 of 13

Symbol(s)

Corrosive

Contains:

Sodium Metasilicate; Sulphonic acids, C14-16-alkane hydroxy and C14-16-alkene, sodium salts

Risk phrases

R35 Causes severe burns.

Safety phrases

S23C Do not breathe vapour or spray.
S51 Use only in well ventilated areas.
S36/37/39B Wear suitable protective clothing, gloves, and eye and face protection.
S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
S28C After contact with skin, wash immediately with plenty of water for 15 minutes.
S45 In case of accident or if you feel unwell, seek medical advice immediately (show the label where

possible).

S1/2 Keep locked up and out of reach of children.

Notes on labelling

Updated per Regulation (EC) 648/2004 on detergents.
Ingredients required per 648/2004: <5%: Anionic surfactants. Contains: Perfumes, hexyl cinnamaldehyde, 2-(4-tert­Butylbenzyl)propionaldehyde, linalool, optical brightener.

2.3. Other hazards

May cause chemical gastrointestinal burns. May cause chemical respiratory tract burns.

SECTION 3: Composition/information on ingredients

Ingredient CAS Nbr EU Inventory % by Wt Classification

Non hazardous ingredient Mixture 80 - 95
Sulphonic acids, C14-16-alkane hydroxy
and C14-16-alkene, sodium salts

68439-57-6 EINECS 270-

407-8

1 - 5 Xn:R22; Xi:R41 (Self

Classified)

Acute Tox. 4, H302; Eye Dam.
1, H318 (Self Classified)

Sodium Metasilicate 6834-92-0 EINECS 229-

912-9

1 - 5 C:R34; Xi:R37 (EU)

Skin Corr. 1B, H314; STOT SE
3, H335 (CLP)
Met. Corr. 1, H290 (Self
Classified)

2-(Propyloxy)ethanol 2807-30-9 EINECS 220-

548-6

1 - 5 Xn:R21; Xi:R36 (EU)

Acute Tox. 4, H312; Eye Irrit. 2,

H319 (CLP)
Please see section 16 for the full text of any R phrases and H statements referred to in this section
Please refer to section 15 for the any applicable Notas that have been applied to the above components

For information on ingredient occupational exposure limits or PBT or vPvB status, see sections 8 and 12 of this SDS

D101, Detailer All Purpose Cleaner (DX-101A): D10101, D10105, D10155

__________________________________________________________________________________________

Page: 3 of 13

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation

Remove person to fresh air. Get immediate medical attention.

Skin contact

Immediately flush with large amounts of water for at least 15 minutes. Remove contaminated clothing. Get immediate
medical attention. Wash clothing before reuse.

Eye contact

Immediately flush with large amounts of water for at least 15 minutes. Remove contact lenses if easy to do. Continue
rinsing. Immediately get medical attention.

If swallowed

Rinse mouth. Do not induce vomiting. Get immediate medical attention.

4.2. Most important symptoms and effects, both acute and delayed

See Section 11.1 Information on toxicological effects

4.3. Indication of any immediate medical attention and special treatment required

Not applicable

SECTION 5: Fire-fighting measures

5.1. Extinguishing media

In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam.

5.2. Special hazards arising from the substance or mixture

None inherent in this product.

Hazardous Decomposition or By-Products

Substance Condition

Carbon monoxide. During combustion.
Carbon dioxide. During combustion.
Irritant vapours or gases. During combustion.

5.3. Advice for fire-fighters

No unusual fire or explosion hazards are anticipated.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Evacuate area. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation
to disperse or exhaust vapours, in accordance with good industrial hygiene practice. Warning: A motor could be an ignition
source and could cause flammable gases or vapours in the spill area to burn or explode. Refer to other sections of this SDS
for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment.

6.2. Environmental precautions

Avoid release to the environment. For larger spills, cover drains and build dykes to prevent entry into sewer systems or
bodies of water.

D101, Detailer All Purpose Cleaner (DX-101A): D10101, D10105, D10155

__________________________________________________________________________________________

Page: 4 of 13

6.3. Methods and material for containment and cleaning up

Contain spill. For large spills, if necessary, get assistance from professional spill clean up team. For small spills, carefully
neutralise spill by adding appropriate dilute acid such as vinegar. Work slowly to avoid boiling or spattering. Continue to add
neutralising agent until reaction stops. Let cool before collecting. Working from around the edges of the spill inward, cover
with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it
appears dry. Absorb spillage to prevent material damage. Remember, adding an absorbent material does not remove a toxic,
corrosivity or flammability hazard. Collect as much of the spilled material as possible. Place in a metal container approved
for use in transportation by appropriate authorities. The container must be lined with polyethylene plastic or contain a plastic
drum liner made of polyethylene. Clean up residue with water. Cover, but do not seal for 48 hours. Dispose of collected
material as soon as possible.

6.4. Reference to other sections

Refer to Section 8 and Section 13 for more information

SECTION 7: Handling and storage

7.1. Precautions for safe handling

For industrial or professional use only. Do not breathe dust/fume/gas/mist/vapours/spray. Do not get in eyes, on skin, or on
clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Wash contaminated clothing
before reuse. Avoid contact with oxidising agents (eg. chlorine, chromic acid etc.) Keep away from reactive metals (eg.
Aluminum, zinc etc.) to avoid the formation of hydrogen gas that could create an explosion hazard.

7.2. Conditions for safe storage including any incompatibilities

Store in a well-ventilated place. Keep container tightly closed. Keep only in original container. Store away from acids.
Store away from oxidising agents.

7.3. Specific end use(s)

See information in Section 7.1 and 7.2 for handling and storage recommendations. See Section 8 for exposure controls and
personal protection recommendations.

SECTION 8: Exposure controls/personal protection

8.1 Control parameters

Occupational exposure limits

No occupational exposure limit values exist for any of the components listed in Section 3 of this Safety Data Sheet.

8.2. Exposure controls

8.2.1. Engineering controls

Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure
Limits and/or control dust/fume/gas/mist/vapours/spray. If ventilation is not adequate, use respiratory protection equipment.

8.2.2. Personal protective equipment (PPE)

Eye/face protection

Wear eye/face protection.
The following eye protection(s) are recommended: Full face shield.
Indirect vented goggles.

Skin/hand protection