USER MANUAL
Table of Contents
Safety Information…………………………………………………..…3
Specifications………………………………………………………….. 4
Main Power Connection…………………………………………….. 5
DMX-512 Connection……………………………………………...... 5
Main Control Menu......................................................................... 6
DMX Profile.................................................................................... 8
Rigging the Fixture……………………………...…………………….11
Cleaning & Maintenance................................................................11
Parts List........................................................................................11
Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured
6. Maximum surface operating temperature 80º.
Protection Against Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. Do not expose unit to rain or moisture.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
3
Technical Information
Part Numbers
3010– XS Led Strobe White
Mechanical Specifications
DMX Connectors: 5 pin XLR connectors in and out
Thermal: Maximum ambient temperature 104°
Maximum surface temperature 140°
Fastening System: Single Mounting Yoke
Display: Digital
Power connection: Power Con in & out
13.66”
4.8”
Fixture 6 Unit ATA Road Case
Size: 13.66” x 4” x 7.12
Weight: 6.5 lb
Size: 30.5” x 23” x 20.66”
Weight: 60.5 lb (empty)
Electrical Specifications
LED Quantity: 324 White SMD LEDS 6500K LED Angle: 140°
Power Input Voltage: 110V-240 50/60 Hz Fuse: 5x20 F5AL250V
Ballast: Elec tr on ic auto sw itch in g
Power Consumption Watts: 259
Amps: 3.49
LED Watts: .80
LED Lifetime: 60 to 100 thous and ho ur s
4”
7.12”
Control & Programming
DMX 512 Protocol
DMX Modes: Mode 1 1 Channels Strobe
Mode 2 3 Channels Dimmer, Duration, Strobe
Mode 3 4 Channels Dimmer, Duration, Strobe, Macro
Mode 4 7 Channels Dimmer, Blinder, Duration, Strobe, Macro, 3 Segment Macros, 9 Segment Macro
Mode 5 13 Channels Dimmer, Intensity X9, Strobe, Macro
Mode 6 1Channel Dimmer
Mode 7 3 Channels Dimmer x 3
Mode 8 9 Channels Dimmer x 9
Control Options: Display Control, Master Slave
4
Main Power Connec-
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 220V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.
The occupation of the connection-cable is as follows:
This fixture is equipped with an electronic power supply that will let the unit operate from 90V to 240V from 50Hz to
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
Green
110V
Connec-
Light Blue
Yellow/Green
N
Connec-
L
Neutral
Ground
220V
Live
L
N
L
220V
L
L
L
DMX-512 Connec-
The fixture is equipped with 5 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a
shielded twisted pair cable designed for RS-485 and 3 pin XLR plugs and connectors in order to connect the controller
with the fixture or the fixture with another.
DMX—input
DMX—output
1
2
5
4
3
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a
120 Ohm resistor between the (-) and the (+) signal into a 3 pin XLR plug and plug it
in to the last fixture on the signal run. Pre-manufactured terminator plugs are available for purchase from your Mega-Lite dealer (P-DMXT).
1. Shield
2. Signal (-)
3. Signal (+)
4. N/A
5. N/A
5
5
4
1
2
3
Display Menu
The control board on the fixture base is your interface to access and
control all the functions on the unit. Its digital display gives you a code
view of the options and functions. The following will explain each function and its options.
CONTROL BOARD
—Mega Lite—
XS LED W
Address
001
Auto
Work Mod
DMX 512
ESC DOWN UP
ENTER
To Set the DMX Start Channel press Enter. Use the Down or Up to select the
desired DMX Start Channel and press Enter to confirm your setting.
This function will give you access to the Preprogramed Chases Press Enter.
Use the Down or Up to select the programed chase, press Enter to confirm your
setting. Use the Down or Up to select the desired speed of the Chase from 1 to 5
press Enter to confirm your setting
DMX 512= This mode w ill allow you to oper ate the fixture with a DMX controller
Master= This Function Allows you to run the Auto Programs Or Audio Programs and send DMX signal out to the Slave units
Slave= On Slave Mode the fixture w ill copy the fun ctions on the Mast er unit
To Set the Desired operational mode press Enter. Use the Down or Up to select
the desired mode and press Enter to confirm your setting.
Chan Mod
ACH
To set the desired operational channel mode press Enter. Use the Down or Up to
select the desired DMX profile operational mode from A,B,C,D,E,F,G and H press
Enter to confirm your setting.
Note: Operational mode are located on Page 8 of the manual.
6
Strobe
Set
This function will give you access to set strobe rate via display. Press Enter.
Use the Down or Up to select the desired color. Press Enter use the Down or Up
to select intensity from 0 to 255. You can repeat this process to get any color
combination.
(Note) once strobe is set you can power up and the last strobe setting will automatically come on.
Strobe
000
Intensity
Set
Tools
White 7
000
Display
Mode
Time
Temp
This function will give you access to set Intensity via display. Press Enter. Use
the Down or Up to select the desired intensity. Press Enter use the Down or Up
to select intensity from 0 to 255. You can control each of the 9 sections .
(Note) once intensity is set you can power up and the last Intensity setting will
automatically come on.
This function will give you access to the Display Control press Enter. Use the
Down or Up to select the desired display operation al Mode fr om Display On
that will leave the display always turned on. Or Display Auto that will make the
display turn off after no usage for 20 seconds., press Enter to confirm your set-
ting.
This function will give you information of how long the fixture has been turned on.
This function gives you information of the fixtures current temperature
Key Mode
DMX
Status
This function will give you access to lock the menu keys so they are not accidently moved. Press Enter. Use the Down or Up to select the desired Key settings
from Lock Or Unlock press Enter to confirm your setting. You will have to hold
the Enter button for 3 seconds, to unlock the keys.
Value
Hold
Value
Clear
If DMX signal is lost. The Fixture will hold the last DMX value
sent.
If DMX signal is lost. The fixture will bring dimmer channels to
zero.
7
DMX Profile
XS LED W 1 Ch A Mode
DMX Channel Function Description Value
1 Strobe
Blinder (full on) 250-255
Strobe Rate (slow to fast) 6-249
No Function 0-5
XS LED W 3 Ch B Mode
DMX Channel Function Description Value
1 Dimmer No Function 0-255
2 Duration Flash Duration 0-255
3 Strobe
Strobe Rate 6-255
No Function 0-5
XS LED W 4 Ch C Mode
DMX Channel Function Description Value
1 Dimmer No Function 0-255
2 Duration Flash Duration 0-255
3 Strobe
Strobe Rate 6-255
4 Macro
Spike Effect 215-255
Ramp Up Effect (slow to fast) 6-42
Ramp Down Effect (slow to fast) 43-85
Ramp Up-Down Effect (slow to fast) 86-128
Random Effect (slow to fast) 129-171
Lightning Effect (slow to fast) 172-214
No Function 0-5
No Function 0-5
8
XS LED W 7 Ch D Mode
DMX Channel Function Description Value
1 Dimmer Dimmer 0-255
2 Blinder
Full On 127-255
3 Duration Flash Duration 0-255
4 Strobe
Strobe Rate 6-255
5 Macro
Spike Effect 215-255
3 Segment
6 Macro
Macro 10 (slow to fast) 226-255
7 9 Segment
Macro
Macro 10 (slow to fast)
Ramp Up Effect (slow to fast) 6-42
Ramp Down Effect (slow to fast) 43-85
Ramp Up-Down Effect (slow to fast) 86-128
Random Effect (slow to fast) 129-171
Lightning Effect (slow to fast) 172-214
Macro 1 (slow to fast) 2-25
Macro 2 (slow to fast) 26-50
Macro 3 (slow to fast) 51-75
Macro 4 (slow to fast) 76-100
Macro 5 (slow to fast) 101-125
Macro 6 (slow to fast) 126-150
Macro 7 (slow to fast) 151-175
Macro 8 (slow to fast) 176-200
Macro 9 (slow to fast) 201-225
Macro 1 (slow to fast) 2-25
Macro 2 (slow to fast) 26-50
Macro 3 (slow to fast) 51-75
Macro 4 (slow to fast) 76-100
Macro 5 (slow to fast) 101-125
Macro 6 (slow to fast) 126-150
Macro 7 (slow to fast) 151-175
Macro 8 (slow to fast) 176-200
Macro 9 (slow to fast) 201-225
Full Off 0-126
No Function 0-5
No Function 0-5
No Function 0-1
No Function 0-1
226-255
9
XS LED W 13 Ch E Mode
DMX Channel Function Description Value
1 Dimmer Dimmer 0-255
2 Intensity Segment 1 Intensity 0-255
3 Intensity Segment 2 Intensity 0-255
4 Intensity Segment 3 Intensity 0-255
5 Intensity Segment 4 Intensity 0-255
6 Intensity Segment 5 Intensity 0-255
7 Intensity Segment 6 Intensity 0-255
8 Intensity Segment 7 Intensity 0-255
9 Intensity Segment 8 Intensity 0-255
10 Intensity Segment 9 Intensity 0-255
11 Duration Flash Duration 0-255
12 Strobe
13 Macro
Ramp Up Effect (slow to fast) 6-42
Ramp Down Effect (slow to fast) 43-85
Ramp Up-Down Effect (slow to fast) 86-128
Random Effect (slow to fast) 129-171
Lightning Effect (slow to fast) 172-214
No Function 0-5
Strobe Rate 6-255
No Function 0-5
Spike Effect 215-255
XS LED W 1 Ch F Mode
DMX Channel Function Description Value
1 Dimmer Dimmer 0-255
XS LED W 3 Ch G Mode
DMX Channel Function Description Value
1 Dimmer Dimmer Segment 1 0-255
2 Dimmer Dimmer Segment 2 0-255
3 Dimmer Dimmer Segment 3 0-255
XS LED W 9 Ch H Mode
DMX Channel Function Description Value
1 Dimmer Dimmer Segment 1 0-255
2 Dimmer Dimmer Segment 2 0-255
3 Dimmer Dimmer Segment 3 0-255
4 Dimmer Dimmer Segment 4 0-255
5 Dimmer Dimmer Segment 5 0-255
6 Dimmer Dimmer Segment 6 0-255
7 Dimmer Dimmer Segment 7 0-255
8 Dimmer Dimmer Segment 8 0-255
9 Dimmer Dimmer Segment 9 0-255
10
Rigging the fixture
Caution!
1. The installations must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Use high quality installation equipment to hang unit.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experience including but not limited to calculating working loads, material being used and periodic safety inspections. If you
lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the fixture has
got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be
checked at least one time a year by a skilled person.
Cleaning and maintenance
Installation Maintenance: The operator has to m ake sure that t he unit is operating saf ely and has the installa-
tions and electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any
safety problems have to be removed.
Note: There is no serviceable parts i nsid e the dev ice except for the L ED’s. Maintenance and service operations are
to be carried out by authorized dealers.
Replacing the fuse: Only replace the fu se with the same typ e and rating.
Replacing the power cable: If the power cable of this device becom es damaged, it has to be r eplaced by aut hor-
ized dealers or trained professional only.
Should you have further questions , please contact your dealer.
Parts List
3010-FAN Replacement fan
3010-PCBM Main PCB card
3010-PS Power Supply
3010-WLED White LED Replacement
3010-WLEDM White LED Module
3010-MUL Multiple Unit Hanger
3010-KNO Knob Set
3010-RC 6 Unit Road Case
11
Warranty Information
Warranty Conditions
-Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty.
-LEDs are not guaranteed to match in color temperature or output.
-It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor.
If purchase date cannot be provided, date of manufacture will be used to determine warranty period.
-Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of
the original invoice.
-Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical
means of shipment.
-Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer. MEGA SYSTEMS
INC. makes no warranties, express or implied, with respect to any product, and Mega Systems specifically disclaims any
warranty of merchantability or fitness for a particular purpose. Mega Systems shall not be liable for any indirect, incidental or consequential damage, including lost profit, sustained or incurred in connection with any product or caused by
product defect or the partial or total failure of any product regardless of the form of action, weather in contract, tort
(including negligence), strict liability or otherwise, and weather or not such damage was foreseen or unforeseen.
- Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Ph 210-684-2600 Fax 210-855-6279
www.mega-lite.com / info@mega-lite.com
Mega-Lite
5718 Kenwick St
San Antonio, TX 78238
Loading...