USER MANUAL
Table of Contents
Safety Information…………………………………………………..…3
Specifications………………………………………………………….. 4
Main Power Connection…………………………………………….. 5
DMX-512 Connection……………………………………………...... 5
Main Control Menu......................................................................... 6
DMX Profile.................................................................................... 8
Rigging the Fixture……………………………...………………….….9
Cleaning & Maintenance.................................................................9
Parts List.........................................................................................9
Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured
6. Maximum surface operating temperature 80º.
Protection Against Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. Do not expose unit to rain or moisture.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
3
Technical Information
Part Numbers
4037– Baby Color VW
Mechanical Specifications
DMX Connectors: 3 pin XLR connectors in and out
Thermal: Maximum ambient temperature 104°
Fastening System: Double Mounting Yoke
Display: Digital
Power connection: Power Con in & out
Maximum surface temperature 140°
8.25”
4.8”
Fixture In ATA Road Case
Size: 8.25” x 4” x 7.25
Weight: 5lb
Size: 10.25” x 9.5” x 6.25”
Weight: 6lb
Electrical Specifications
LED Quantity: 7 LED Angle: 20°
Diffusion Beam Angel: 25°
Amber: 7 Power Input Voltage: 110V-240 50/60 Hz
Warm White: 7
Cool White: 7 Ballast: Elect ronic auto sw it chin g
Power Consumption Watts: 29
LED Watts: 5
LED Lifetime: 60 to 100 t housand h ours
Amps: .42
4.25”
7.25”
Control & Programming
DMX 512 Protocol
DMX Modes: Mode 1 3 Channels Amber, Warm White, Cool White
Control Options: Audio Trigger, Master Slave
Mode 2 4 Channels Dimmer, Amber, Warm White, Cool White
Mode 3 6 Channels Dimmer, Amber, Warm White, Cool White, CTO, Strobe
4
Main Power Connection
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 220V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.
The occupation of the connection-cable is as follows:
This fixture is equipped with an electronic power supply that will let the unit operate from 90V to 240V from 50Hz to
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
Green
110V
Connec-
Light Blue
Yellow/Green
N
Connec-
L
Neutral
Ground
220V
Live
L
N
L
220V
L
L
L
DMX-512 Connection
The fixture is equipped with 3 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a
shielded twisted pair cable designed for RS-485 and 3 pin XLR plugs and connectors in order to connect the controller
with the fixture or the fixture with another.
DMX—input
1
2
3
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a
120 Ohm resistor between the (-) and the (+) signal into a 3 pin XLR plug and plug it
in to the last fixture on the signal run. Pre-manufactured terminator plugs are availa-
DMX—output
1. Shield
2. Signal (-)
1 2
3. Signal (+)
3
5
Display Menu
The control board on the fixture base is your interface to access and
control all the functions on the unit. Its digital display gives you a code
view of the options and functions. The following will explain each function and its options.
CONTROL BOARD
Enter
DMX Address
1-512 0-255
DMX Mode
3-Ch
4-Ch
6-Ch
Amber Dimmer
Warm White Dimmer
0-255 0-15
Cool White Dimmer
0-255
Strobe
0-15
Fade
Menu Up Down
Dimming Curve
0-4
DMX Address
Press Enter to select the DMX start channel use the up/down keys, display will be flashing once you have selected
the desired start channel Press Enter to confirm display will stop flashing.
DMX Mode
This function allows you to select the mode in witch you want to control the fixture. Press Enter use the up/down keys to
select desired DMX mode settings. Press Enter to confirm the settings.
3 CH Amber, Warm White, Cool White
4 CH
6 CH
Dimmer, Amber, Warm White, Cool White
Dimmer, Amber, Warm White, Cool White, CTO, Strobe
Amber Dimmer
This function allows you to dim up or down the amber LED’s . Press Enter use the up/down keys to select desired dim-
mer settings. Press Enter to confirm the settings.
Warm White Dimmer
This function allows you to dim up or down the warm white LED’s . Press Enter use the up/down keys to select desired
dimmer settings. Press Enter to confirm the settings.
Cool White Dimmer
This function allows you to dim up or down the cool white LED’s . Press Enter use the up/down keys to select desired
dimmer settings. Press Enter to confirm the settings.
6
Flash
This function allows you to strobe all the LED’s. Press Enter use the up/down keys to select desired strobe speed set-
tings from 0 to 15. Press Enter to confirm the settings.
Fade Scroll
This function allows you to fade the LED’s from one color to another. Press Enter use the up/down keys to select desired
fade speed settings from 0 to 15. Press Enter to confirm the settings.
Dimming Speed
Press Enter to select the desired dimming speed when used with a DMX controller. Use the up/down keys to select from
0 to 4. 0 speed will be the fastest 4 will be the slowest. Press Enter to confirm.
DMX Indicator
CONTROL BOARD
Menu Up Down
Enter
When DMX Signal is being received the last point on the control board display will turn on. If
there is no DMX signal present is will be off.
7
DMX Profile
Baby Color VW 3Ch
DMX Channel Function Description Value
1 LED Color Amber LED intensity 0-255
2 LED Color Warm White LED Intensity 0-255
3 LED Color Cool White LED Intensity 0-255
Baby Color VW 4Ch
DMX Channel Function Description Value
1 Dimmer Dimmer Off to Full 0-255
2 LED Color Amber LED intensity 0-255
3 LED Color Warm White LED Intensity 0-255
4 LED Color Cool White LED Intensity 0-255
Baby Color VW 6Ch
DMX Channel Function Description Value
1 Dimmer Dimmer Off to Full 0-255
2 LED Color Amber LED intensity 0-255
3 LED Color Warm White LED Intensity 0-255
4 LED Color Cool White LED Intensity 0-255
5 CTO 2800K to 8000K 0-255
6 Strobe
Strobe (slow to fast) 0-196
Random Strobe (slow to fast) 197-255
8
Rigging the fixture
Caution!
1. The installations must be carried out by an authorized dealer or trained profes-
sional.
2. Unit may cause severe injures if you have doubts concerning the safety do not
install.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experience including but not limited to calculating working loads, material being used and periodic safety inspections. If you
lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the fixture has
got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be
checked at least one time a year by a skilled person.
Cleaning and maintenance
Installation Maintenance: The operator has to make sure that the unit is o perating safely and has the ins talla-
tions and electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any
safety problems have to be removed.
Note: There is no serviceab le parts inside the devic e except for the L ED’s. Maintenance and service operations are
to be carried out by authorized dealers.
Replacing the fuse: Only rep lace the fuse with the same type and rating.
Replacing the power cable: If t he power cable of thi s device becomes damag ed, it has t o be rep laced by author-
ized dealers or trained professional only.
Should you have further questions , please contact your dealer.
Parts List
4035-FAN Replacement fan
4037-MPCB Main PCB card
4037-PS Power Supply
4037-DIS Display
4035-DF Removable Diffusion Filter
4037-LED LED Replacement
4035-KNOB Knob Set
9
Warranty Information
Warranty Conditions
-Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty.
-LEDs are not guaranteed to match in color temperature or output.
-It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor.
If purchase date cannot be provided, date of manufacture will be used to determine warranty period.
-Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of
the original invoice.
-Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical
means of shipment.
-Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer. MEGA SYSTEMS
INC. makes no warranties, express or implied, with respect to any product, and Mega Systems specifically disclaims any
warranty of merchantability or fitness for a particular purpose. Mega Systems shall not be liable for any indirect, inci-
dental or consequential damage, including lost profit, sustained or incurred in connection with any product or caused by
product defect or the partial or total failure of any product regardless of the form of action, weather in contract, tort
(including negligence), strict liability or otherwise, and weather or not such damage was foreseen or unforeseen.
- Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Ph 210-684-2600 Fax 210-855-6279
www.mega-lite.com / info@mega-lite.com
Mega-Lite
18668 Hwy 16 N.,
Helotes, TX 78023
Loading...