LED SPOT 90
MJ-1014
User manual
Thank you for choosing our 90W LED moving head light. For the sake of your safety, Please
read and follow these instructions carefully and keep this manual in a safe place for future
reference.
LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0
Catalogue
Chapter Page
Safe Usage Of The Product -----------------------------------------------------------------------------------------3
Install The Equipment ------------------------------------------------------------------------------------------------4
Power Code Connection ---------------------------------------------------------------------------------------------4
DMX Connection ------------------------------------------------------------------------------------------------------5
DMX Terminator -------------------------------------------------------------------------------------------------------6
Function Set---------------------------------------------------------------------------------------------------------------6
Operation Menu ---------------------------------------------------------------------------------------------------------6
Maintenance --------------------------------------------------------------------------------------------------------------8
Keeping The Product Clean ------------------------------------------------------------------------------------------9
Trouble Shooting---------------------------------------------------------------------------------------------------------9
Equipment and Appendix----------------------------------------------------------------------------------------------9
Channel List---------------------------------------------------------------------------------------------------------------9
Technical Parameters---------------------------------------------------------------------------------------------------11
☆Important notice:
· In this instruction for use contains about the installment and the use aspect important information of the LED moving
head. When installing and using, you need to look this usage instruction strictly.
· Before open the LED moving head and if you want to do the repair work, please make sure the power source is at the
separation condition.
· Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and the unit are
in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer
and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer or dealer.
Attention: Unceasingly carries on the product improvement about our company the policy, in this instruction booklet
carries the data will have the possibility to be able to change in the future, when no longer separate notice change matters
concerned. Our company retains when the product improvement changes the related specification the authority. This
instruction booklet publisher cannot be responsible regarding this instruction booklet in information accuracy, also cannot
the related consequence which causes regarding these information be responsible.
LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0
3
SAFE USAGE OF THE PRODUCT
When unpacking and before disposing of the carton, check there is no transportation damage before
using the product. Should there be any damage caused by transportation, consult your dealer and do
not use the apparatus.
The product is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain
and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other
liquids.
The product is not designed or intended to be mounted directly on to inflammable surfaces
The product is only intended for installation, operation and maintenance by professional person.
The product must be installed in a location with adequate ventilation, at least 50cm from adjacent
wall surfaces. Be sure that no ventilation slots are blocked.
Do not product the beam onto inflammable surfaces, minimum distance is m.
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power
requirements of the projector.
It is essential that each projector is correctly earthed and that electrical installation conforms to all
relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the
power-cord come into contact with other cables. Only handle the power-cord by the plug. Never pull
out the plug by tugging the power-cord.
Keep the optical system clean. Do not touch the lens with bare hands.
The product should always be installed with a secondary safety fixing. On the projector base brink,
there is a hole for the safety cord provided. It should be attached as shown in “installing the
projector” section.
The lens shall be changed if they have become visibly damaged to such an extent that their
effectiveness is impaired, for example by cracks or deep scratches.
Exterior surface temperatures of the luminaire after 5 minutes operation is 40°C，when steady state is
achieved 50°C.
There is no user serviceable parts inside the projector, do not open the housing and never operate the
product with the covers removed.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
★Always disconnect from the mains, when the device is not in use or before cleaning it or
before attempting any maintenance work !
www.mjledlighting.com
LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0
4
Install The Equipment:
Use 2pcs clamp and 1safety cord(need to purchase).Use clamp fix with light hook which in the
packing box with light, then use screw install to the bottom of lamp. Hang the fixture on the structure
and fasten the screws attached to each clamp. Make sure the light is installed reliable, and confirm
the light which you fixed is strong enough for hanging the light. Base on safety reason, please
according to the above picture using safety wire cross the light to make it strong enough again.
Warning!
1．Light Hook and clamp only use for hanging the light. Do not use clamp as a tool to move fixtures.
2．Base on safety reason, please use the safety cord which can afford the weight ten times of lamp
through Insurance hole for auxiliary hanging.
3．Don't use the handle of the moving head light to fixed or lift!
Power Code Connection:
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Use the plug provided to connect the mains power to the projector paying attention to the voltage and
frequency marked on the panel of the projector. It is recommended that each projector be supplied
separately so that they may be individually switched on and off.
★It is essential that each projector is correctly earthed and the electrical installation conforms
to all relevant standards.
www.mjledlighting.com
LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0
5
DMX Connection:
Connection between the controller and a projector and between one projector and another must be
made with a 2 core-screened cable, with each core having at least a 0.5mm diameter. Connection to
and from the projector is via cannon 3 pin (which are included with the projector) XLR plugs and
sockets. The XLR's are connected as shown in the figure above.
Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each
other. The body of the plug is not connected in any way. The XLED 590 accepts digital control
signals in protocol DMX512 (1990).
Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the
second fixture’s input and connect the rest fixtures in the same way. Eventually connect the last
fixture’s output to a DMX terminator as shown in the figure below.
www.mjledlighting.com
LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0
6
DMX Address Set(001-512)
Address
LCD Display
DMX Terminator:
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a
DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control
signals.
The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins
2 and 3, which is then plugged into the output socket on the last projector in the chain. The
connections are illustrated below.
Function Set:
MENU DOWN UP ENTER
Use button switch and LCD display, can set the address code and function code easily.
Check or modify lighting function settings, Press the MENU or ENTER button. LCD display panel will
display main menus. Function operation menu all have corresponding submenu . Each menu all represent the
specific functions of lamps, specific see below "operation menu" section.
Set or browse function setting of lamp, Press UP or DOWN key.
Press ENTER key to save your changes or to ENTER submenu, Press UP or DOWN can change
value(Plus or reduce number).
Operation Menu:
Menu Structure chart
Main Menu Sub Menu
www.mjledlighting.com
LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0
7
Option
X Reverse
Y Reverse
Display
XY Exchange
Language
Poorlight
Display LOGO
Man Control
CH1
CH2
CH3
CH18
Sound
Test operation
Auto
Program run
Program run
Resume default
Fixture reset
Lighteness
Yes/No
Yes/No
Chinese
English
1-32
Constant open
Dim
Off
ON/OFF
0－255
0－255
0－255
0－255
Yes/No
Enter
Enter
…… ……
Sub menu include address, Option, Display, Man Control , Test operation, Resume default, and Fixture
reset..
Address setting,
1. Press “Menu” button to Set DMX Address，to confirm by press “ENTER” button。
2. Show Set DMX address DMX address:001，correct by pressing “UP&DOWN” button。
3. Press “ENTER” button to save and quit. Press “MENU” button to quit no saving
Option
Press “Menu” , and choose Option by “UP&DOWN”，it will be show X Reverse , Y Reverse,
XY Exchange three mode, to confirm by press “ENTER” button.
1. X Reverse Settings, Choose menu by pressing ”UP&DWON” button, will show YES/NO,.
correcting by “ENTER” Button..
www.mjledlighting.com
LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0
8
2. Y Reverse Settings, Choose menu by pressing ”UP&DWON” button, will show YES/NO,.
correcting by “ENTER” Button..
3. XY Exchange Settings, Choose menu by pressing ”UP&DWON” button, will show YES/NO,.
correcting by “ENTER” Button..
Display
Press “Menu” , and choose Display by “UP&DOWN”，it will be show Language, Lighteness,
Poorlight three mode, to confirm by press “ENTER” button.
1. Language Settings, Choose menu by pressing ”UP&DWON” button, will show Chinese/English,.
correcting by “ENTER” Button.
2. Lighteness Settings, Choose menu by pressing ”UP&DWON” button, will show 1 to 32,.
correcting by “ENTER” Button.
3. XY Exchange Settings, Choose menu by pressing ”UP&DWON” button, will show Constant
open, Dim, Off. correcting by “ENTER” Button.
Man Control
Press “Menu” , and choose Man control by “UP&DOWN”，it will be show CH1 to CH16, to
confirm by press “ENTER” button.
1. CH1 . Press the ENTER then pressing ”UP&DWON” button, will show 001 to 255,.
correcting by “ENTER” Button.
2. CH2 . Press the ENTER then pressing ”UP&DWON” button, will show 001 to 255,.
correcting by “ENTER” Button.
…………………………
3. CH18 . Press the ENTER then pressing ”UP&DWON” button, will show 001 to 255,.
correcting by “ENTER” Button.
Test operation
Press “Menu” , and choose Test operation by “UP&DOWN”，it will be show Sound or Auto
mode, to confirm by press “ENTER” button.
Resume default
1. Press “Menu” and choose Resume default by “UP&DOWN”，confirm by press “ENTER” button,
it shows factory settings
Fixture rese
Press “Menu” and choose Fixture rese by “UP&DOWN”，confirm by press “ENTER” button, it
shows reset.
Maintenance:
To prolong the life of the projector, some maintenance work has to be done to ensure the LED
optical system in good condition. If the projector does not function, check the fuses on the power
socket of the projector, they should only be replaced by fuses of the same specification. Should
these be damaged, call a qualified technician before replacement. The projector has thermal
protection device that will switch off the projector in case of overheating. Should either of these
operate, check that the fans are not blocked, and if they are dirty, clean them before switching on the
projector again. Check that the fans are operational, if not, call a qualified technician.
☆Any maintenance work should only be carried out by qualified technicians.
www.mjledlighting.com
LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0
9
Problem
Answer
The LED moving head light doesn’t switch
on.
Check the fuse the power socket
Although shines, but the LED moving head
lamp doesn’t accept the instruction of the
controller.
Check the digital start address and
also check the connection situation of
the communication control line
LED moving head lamp only can work
intermittently.
Inspect the power supply and voltage
is whether normal.
Do not receive the DMX512 signal.
Whether the signal lines do contact
well or broken.
The light beam appears gloomily.
Check that the heat dissipation
system is running normally or Inspect
the optics part is whether clean.
Channel
Function
Value
Function Description
CH1
Dimmer
0-255
Dimmer 0-100%
CH2
Strobe
0-240
Strobe from slowly to quickly
241-255
Light ON
Keeping The Product Clean:
To ensure the reliability of the projector, it should be kept clean. It is recommended that the fans
should be cleaned every 15 days. LED lens should also be regularly cleaned to maintain an optimum
light output.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or
particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics. A soft cloth
and typical glass cleaning products should be used for cleaning. It is recommended to clean the
external optics at least once every 15 days.
☆Do not use any organic solvent, e.g. alcohol, to clean housing of the apparatus.
Trouble Shooting:
☆Other maintain work should by the specialist which has the experience to carry on.
Equipment and Appendix:
The packing list of this light as follows:
☆ Led moving head light 1pcs
☆ XLR connector 1unit
☆ Light Hook 2pcs
☆ M8 Screw 4pcs
☆ The Product of Instruction 1pcs
Channel List:(18CH)
www.mjledlighting.com
LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0
10
CH3
Color
0~15
White
16~31
Red
32~47
Green
48~63
Yellow
64~79
Blue
80~95
Pink
96~111
Cyan
112~126
Orange
127~190
Rainbow effect(Fast~slow)
191~255
Rainbow effect(slow~Fast)
CH4
Color half step
0~255
Color half step
CH5
Pan
0~255
Pan movement
CH6
Tilt
0~255
Tilt movement
CH7
prism
0~255
prism
CH8
Prism Rotation
0~255
Prism Rotation
CH9
Gobo1
0~15
White
16~31
Gobo 1
32~47
Gobo 2
48~63
Gobo 3
64~79
Gobo 4
80~95
Gobo 5
96~111
Gobo 6
112~127
Gobo 7
128~190
Rainbow effect (Fast ~slow)
191~255
Rainbow effect (slow~Fast)
CH10
Gobo1 Rotation
0~255
Gobo Rotation
CH11
Gobo1 half step
0-255
Gobo Half Step
CH12
Gobo2
0~12
White
13~25
Gobo 1
26~38
Gobo 2
39~51
Gobo 3
52~64
Gobo 4
65~77
Gobo 5
78~90
Gobo 6
91~103
Gobo 7
104~116
Gobo 8
117~127
Gobo 9
128~191
Rainbow effect (Fast ~slow)
192~255
Rainbow effect (slow~Fast)
CH13
Iris
0~255
Iris
CH14
Focus
0~255
Focus
CH15
Pan Fine
0~255
Pan Fine
www.mjledlighting.com
LED Moving Head Wash 3610 MJ-1006C User Manual ver2.0
11
CH16
Tilt Fine
0~255
Tilt Fine
CH17
Speed
0~255
XY speed
CH18
Reset
0~255
Reset
Technical Parameters:
Voltage: AC90V-240V; 50/60Hz
Power Consumption: 150W (220V)
LED Bulbs: 90W*1pcs White LUMEN LED
LED Current: 12A
LED Lifetime: 50000Hours
Color: 7color + blank color wheel
Gobo: 9Fixed Gobo + 1 blank Gobo
7Rotation Gobo + 1 blank Gobo
Prism : rotation 3-face prism, Bilateral rotation, Iris function.
Adjusts the light: 0-100 electron adjusts the light, various colors may alone move also may mix the
color tone
Strobe: 1-25/second high speed strobe, but single color Mixes the color strobe
Head Movement: Pan 540°, Tilt 270°, with auto position correction and electronic replacement
function.
Control mode: DMX 512, Stand –alone mode, Self-test mode, Sound, Master/slave
DMX Channel: 18CH
Control Panel: LCD display panel
IP Grade: IP20
Work Environment Temperature: -20°C~40°C
Net weight:12KG
Gross Weight:14kg
Package Size: 39 x 36x 50cm
Light Size(see it below)
www.mjledlighting.com
Loading...