MEGA 3100
2-WAY LCD PAGER
MOTORCYCLE ALARM
Operation Manual
MEGATRONIX
CHATSWORTH, CA. U.S.A.
MEGA 3100 OPERATE
1
MEGA 3100 OPERATE
2
TABLE OF CONTENTS:
A. REMOTE TRANSMITTER OPERATION ……………………………………….…………………….………..3
B. 2-WAY LCD REMOTE CONTROL TRANSCEIVER OPERATION ONLY.………..…………………..….. 3
C. LED DISPLAY .……………..……………………………………………………………………….……………. 3
D. CHIRP INDICATOR ..………..……………………………………………………………………………..……. 4
E. PARKING LIGHT …….……..…………………………………………………………………………..….……. 4
F. ALARM OPERATION CONDITION .…………………………………………………………………………… 4
G. ACTIVE ARMING – ARM & LOCK .…………………………………………………………………………… 4
Silent Arming
Arming with Noiseless Mode
Arming with Shock Sensor By-Pass
Passive Start Disable
Arming with Pathway Illumination
Arming with Hidden Alarm Function
H. PASSIVE ARMING – …….………….…………………………………………………………………………… 4
Passive Arming By-Pass
I. ACTIVE DISARMING .…………………………..……………………………………………………..…………. 4
Clear The Flash Icon
Silent Disarming
Tamper Disarming
Pathway Illumination
Automatic Re-Arm
J. DISARMING WITHOUT A TRANSMITTER .……………..…………………………………………………… 5
Overrides the Alarm without Password Pin Code
Overrides the Alarm With Password Pin Code
K. VALET MODE .……………..……………………………………………………………………….……….…… 5
Enter Valet Mode
Exit Valet Mode
Remote Valet
L. CAR LOCATOR .……………………………………………………………………….………………………… 6
M. PANIC FUNCTION .………………………………………………………………………………...…………… 6
N. TRIGGER THE SYSTEM .………………………………………..…………………………..……….………… 6
Clear The Flash Icons and Melody Sound
Clear The Melody Sound Only
Noise Abatement Circuit
O. SYSTEM’S TRIGGER CHECK ………………………………………………………………….….…...…….. 6
P. DRIVER PAGING / LOSE AND FOUND……………………….…………..…………………………..……… 7
Q. CHANNEL 3 TIMER CONTROL OUTPUT …………………………………………………………….…….. 7
R. CHANNEL 4 TIMER CONTROL OUTPUT ………..………………………………………………....…..…... 7
S. POWER ON MEMONRY: ………..…………………………………………………………………..….….…… 7
LCD REMOTE TRANSCEIVER:
A. BATTERY REPLACEMENT ……………………………….……………………………………………….….. 7
B. THE REMOTE LCD ICONS WITH FUNCTION ……….…………………………………………………..…. 7
C. PROGRAMMING OF THE LCD REMOTE TRANSCEIVER ……………………………………………..… 8
1. Screen Lamp ON.
2. Power Save Mode For Remote Transceiver
3. Clear The Flash Icon and Melody Sound
4. Stop The Melody Sound.
5. Button Lock
6. Vibration / Melody Mode
7. Enable / Disable Bi Sound While Pressing Button:
8. Low Battery Indication.
9. Set Up Fixed Count Down Timer
10. Out Of The Range Check
11. Illumination
D. TIMER SETTING ……………………………….………………………..…………………….…………….… 8
1. Timer Setting.
2. Alert Alarm Timer Setting
3. Count Down Timer Setting
MEGA 3100 OPERATE
3
OPERATION:
A. TRANSMITTER OPERATION:
Transmitter Button System Function Remark
Arm the System
Press and release momentarily
-
Arming with Noiseless Mode
Press button within 3 seconds after
arming
.
- -
Arming with Shock Sensor Bypass
Press button 2 times within 5 seconds
after arming
- F
Arming with Pathway Illumination
Press the button first within 3
seconds press
F
F -
Silent Arm
Press the
F button first within 3
seconds press
+
Arming with Hidden Alarm
Press the
and buttons together
Car Locator Upon armed
(3 seconds)
Panic
Press and Hold button for 3 seconds
Disarm System
Press and release momentarily
- F
Disarming with Pathway Illumination
Press the button first within 3
seconds press
F
F -
Silent Disarm
Press the
F button first within 3
seconds press
F - F
Passive Arming By-pass
Upon disarmed, press the
F button
twice within 3 seconds.
F - F - F
Remote control Enter/Exit Valet mode
Press the
F button 3 times within 5
seconds.
F (2 seconds)
Channel # 3 Timer Output Press and Hold for 2 seconds
+ F (2 seconds)
Channel # 4 Timer Output
Press the
and F buttons together
B. FOR 2-WAY LCD TRANSCEIVER OPERATION ONLY:
Transceiver Button System Function Remark
Motorcycle Locator
Press and release momentarily
(3-second)
Panic function
Press and Hold
button for 3
seconds
- (C)
System’s Trigger Check
Press the
button first within 3
seconds press
(C)
- -
Clear the Flash Icon and Melody Sound
on the LCD Screen Transmitter
Press the
button 3 times within 5
seconds.
C. LED INDICATORS:
LED Function LED Function
Off Disarmed 2 flashes... pause Zone 2 / Activated on the Tilt Switch
Slow Flash Armed 3 flashes... pause Zone 3 / Activated on the Close Loop
Flash Passive Start Disable 4 flashes... pause Zone 4 / Activated on the Shock Sensor
Fast Flash Passive Arming 5 flashes... pause Zone 5 / Activated on the Ignition Switch
On (Solid) Valet Mode
D. CHIRP INDICATORS: E. PARKING LIGHT:
Chirp Function Parking light Function
1 chirp Arm 1 flash Arm
2 chirps Disarm 2 flashes Disarm
4 chirps Disarm / Triggered 3 flashes Disarm / Triggered
6 chirps Car locator
12 flashes Car locator
MEGA 3100 OPERATE
4
F. SYSTEM OPERATING CONDITION:
Siren, Horn Parking Light LED Starter
1. Arming 1 Chirp 1 Flash Slow Flash Disable
2. Disarming 2 or 4 Chirps 2 or 3 Flashes Fast Flash or Off
3. Trigger Alarming Flashes Slow Flash Disable
4. Passive Starter Disable Flash Disable
5. Panic Alarming Flashes
6. Car Locator 6 Chirps 12 Flashes
G. ACTIVE ARMING:
1. Press button on transmitter.
2. The siren will chirp once and the parking light will flash once indicating the system is
armed. The LED will begin to flash and the engine starter will be disabled.
SILENT ARMING:
Press the F button first, within 3 seconds press button on the
transmitter will arm your security system, No chirp sound will be heard, arm
confirmation will be through the motorcycles parking lights only.
ARMING WITH NOISELESS MODE: With the system disarmed, press the
button once, the siren will
chirp once. Within 3 seconds, press
button again. The siren will emit one short chirp indicating the system
is set and will be fully armed in 5 seconds with the noiseless mode for one arming cycle. In this mode,
whenever strong vibration or lesser vibration is presented to the protected motorcycle, the shock sensor
cannot trigger the system and just only emit a few warn away chirps.
ARMING WITH SHOCK SENSOR BY-PASS: Press the
button on the transmitter three times within 5
seconds will arm the security system, by-pass the shock sensor. The system will chirp one additional time to
confirm the sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one
arming cycle only. The security system will return to normal operation during the next arming cycle.
PASSIVE STARTER DISABLES: (See Feature I
- 2 Programming)
The purpose of the feature is to protect the motorcycle from being stole at all times, regardless of whether or
not the alarm is armed.
The starter of the vehicle will be disable 60 seconds after the ignition is turned off. Once the key is turned off,
the LED will flash fast for 60 seconds.
After 60-second timer has elapsed, the LED will flash slowly (one-half its normal armed rate) to indicate the
passive starter disable is activated and the system will not respond to any trigger input except the ignition
trigger.
ARMING WITH PATHWAY ILLUMINATION: Press the
button once to arm the system, the siren will chirp
once. Within 3 seconds, press
F button. The parking light will be turns “ON” for 30 seconds to illuminate your
pathway.
HIDDEN ALARM FUNCTION: Press
and buttons at the same time the security system will arm and
with “Hidden Alarm Function”. The siren / horn will be silenced even if the sensor is triggered in the armed
status.
H. PASSIVE ARMING (See Alarm Feature I – 3 Programming)
Active arming / disarming is controlling your security system via the remote transmitter. This security system
is equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds
after the ignition switch is turns off. Operation is as follows.
1. Turn the ignition to the “OFF” position.
2. The security system LED will flash fast for 30 seconds. Each time a sensor is triggered during the passive
arming countdown, the 30-second countdown starts over.
3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren will chirp [1]
time and the parking lights will flash [1] time.
PASSIVE ARMING BY-PASS: While the system disarmed, press the
F
button twice within 3 seconds, the
security will respond with [1] chirp and LED will turn “ON”. The security system will remain in this temporarily
state for as long as you wish. To exit passive by-pass, press the
button or button and the system will
return to normal status.
I. ACTIVE DISARMING –
1. Press button on the transmitter.
2. The siren will chirp twice and parking light will flash twice to indicating that the security system is now
disarmed.
MEGA 3100 OPERATE
5
System Disarm
Activated on the
Tilt Sensor
Activated on the
Close Loop
Activated on the
Shock Sensor
Activated on the
Ignition Switch
Clear The Flash Icon: Press the button 3 times within 3 seconds will clear the flash icon on the LCD
screen transceiver.
SILENT DISARMING: Press the F button first, within 3 seconds press button to silent disarm your
security system, No chirp sound will be heard, arm confirmation will be through the motorcycles parking lights
only.
TAMPER DISARMING: If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash 3
times.
DISARMING WITH PATHWAY ILLUMINATION: Press the
button once to disarm the system, the siren
will chirp once. Within 3 seconds, press
F button. The parking light will be turns “ON” for 30 seconds to
illuminate your pathway.
AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm itself 60
seconds after disarming with remote transmitter. Press the
F button twice within 3 seconds or turns on the
ignition switch will cancel the rearm.
(See Alarm Feature I – 2 Programming)
J. DISARMING WITHOUT A TRANSMITTER
OVERRIDE THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default Setting)
The Override function may be used if the remote transmitter is lost or inoperative.
1. Turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Within 10 seconds push and release the valet switch
The alarm will stop sounding and enter the disarm mode. You can now start and operate the motorcycle
normally.
OVERRIDE THE ALARM WITH PASSWORD PIN CODE:
(See Alarm Feature III – 2 Programming)
Unlike valet switch easily found, and defeated, this security system allows the consumer to program a
password pin code. Offering a higher level of security.
1. Turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Press the Valet switch the selected number of times (1-9 presses) within 15 seconds.
(Press the Valet switch, system's siren will stop alarming, parking light will stop flashing, but the
motorcycle cannot be start and drive away until you disarm the system.)
The system should now disarm. If it does not, you may have waited too long to press the Valet switch; turn
the ignition off and on and try again.
K. VALET MODE: (System in Disarm or Valet mode)
The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your
transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm function
are bypassed, however the remote panic feature and Channel 3 /4 will remain operational. To use the valet
mode, the system must first be disarmed either by using you remote transmitter, or by operating the Manual
override sequence.
Enter Valet Mode:
1. From the disarmed condition, turn the ignition to “ON” position.
2. Push and hold valet switch for 2 seconds until the LED turns on. The LED wills
remain on as long as the system is in 'valet mode'.
Exit Valet Mode:
1. Return to normal operation, turn ignition 'on'.
2. Push and hold valet switch for 2 seconds, The LED wills turns off indicate the system
are exiting the valet mode.
REMOTE VALET: (System in Disarm or Valet mode)
Press and release the
F
button three times within 3 seconds to enter / exit valet mode.
A parking light flash to confirm enter valet mode
Two parking light flashing to confirm exit valet mode.
MEGA 3100 OPERATE
6
L. MOTORCYCLE LOCATOR:
Press the button on the 5-button 2-way transceiver or press the button on the 3-button transmitter
upon armed mode to active motorcycle locator function. The siren will chirp 6 times. The parking light will
flash 12 times, for you to easily locate your motorcycle.
M. PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger the alarm in
case emergency. To activate the panic mode, press and hold
or button of your
transmitter for 3 seconds. The siren will sound and continue for 30 seconds or until
or
button is activated a second time.
N. TRIGGER THE SYSTEM
When armed, your motorcycle is protected as follows:
1. Light impacts will trigger the warn-away signal. A long chirp from siren/horn.
2. Heavy impacts will trigger the system. The full trigger sequence is 30 seconds of constant siren and
flashing parking lights.
3. If the tilt switch is triggered / the close loop wires of the connection are not in contact / the ignition is turned
on while the system is armed, the full trigger sequence will activate.
4. The starter kill prevents the motorcycle’s starter from cranking.
Activated on the
Tilt Sensor
Activated on the
Close Loop
Activated on the
Shock Sensor
Activated on the
Ignition Switch
Warn-away
Trigger
Clear The Flash Icon And Melody Sound:
While triggering the alarm the LCD screen will alert user through
melody sound and flashing trigger icon, press the
button 3 times within 3 seconds will clear the flash
icon and stop melody sound on the LCD screen transceiver.
Stop The Melody Sound Only:
While triggering the alarm the LCD screen will alert user through melody
sound and flashing trigger icon, press any button on the LCD remote transceiver to stop melody sound only.
NOISE ABATEMENT CIRCUIT: Your system has “Noise Abatement Circuit”. It prevents annoying
repetitive trigger sequences due to faulty sensor or environmental condition such as thunder, jackhammers
airport noise, etc.
Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each time, the same sensor or
switch is triggering the alarm. “Noise Abatement Circuit” will interpret this pattern of triggers as false alarm.
After the fifth trigger, “Noise Abatement Circuit” ignores, or by pass, that sensor or switch until the other
sensor or switch is trigger.
O. SYSTEM’S TRIGGER CHECK (For two-way transceiver operation only)
Press the transceiver
button first, within 3 seconds press (C) button. It
responds with one melody sound and all trigger’s records will immediately displayed on
the LCD screen.
P. DRIVER PAGING / LOSE AND FOUND (For two-way transceiver operation
only)
It is useful the event that someone wants to page the driver of the parked motorcycle or
someone cannot find his LCD motorcycle remote transceiver.
Upon disarmed, press and hold the Valet
switch for 2 seconds to page the driver, one
chirp sound shall be emitted from the motorcycle and the paging melody sound
continues sounding from you Remote LCD transceiver and “
” indication flashes on
the LCD screen.
Q. CHANNEL 3 TIMER CONTROL OUTPUT.
Press and hold the F button on transmitter for two seconds to remote control the channel 3 output.
Channel 3 is user-programmable timer output. You may program the built-in timer to send a ground signal /
latch / latch with ignition / 30 seconds/ 60 seconds/ 90 seconds timer output.
MEGA 3100 OPERATE
7
Note1: Factory default setting at 1second pulse grounded output
(See Alarm Feature II – 2 Programming).
Note2: Upon activate the channel 3; the siren/horn will emit one chirp to indicator the channel 3 is latch on or
emit two chirps to indicator the channel 3 is latch off.
R. CHANNEL 4 TIMER CONTROL OUTPUT
Press the transmitter
and F buttons at the same time to active Channel 4 function.
Channel 4 is user-programmable timer output. You may program the built-in timer to send a momentary /
latch / latch with ignition / 30 seconds/ 60 seconds/ 90 seconds timer output.
Note1: Factory default setting at momentary output
(See Alarm Feature II – 3 Programming).
Note2: Upon activate the channel 4; the siren/horn will emit one chirp to indicator the channel 4 is latch on or
emit two chirps to indicator the channel 4 is latch off.
S. POWER ON MEMONRY:
This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power
is lost and then reconnected.
2-WAY LCD REMOTE TRANSCEIVER:
Note: If the system is interfered by stronger radio frequency around, sources of high voltage electric power or
such Obstacles like tall buildings and so on, the transmission range may get shorter as the system uses
low out put powered frequency.
A. BATTERY REPLACEMENT:
A 1.5V type AAA Alkaline battery powers the Remote Transceiver. When the power of the battery weakens a
icon shall be displayed on the LCD screen. When the old battery is replaced to new one, there will be
beep sounds indicate the power is up and the clock on the LCD screen returns to AM12:00 after displaying
all the icons. Correct the time by pressing
for 3 seconds before using (See Timer Setting).
Note : Press the
button two times when the battery compartment is empty, then insert the new battery.
B. THE REMORE LCD ICONS WITH FUNCTION:
Armed Mode
Your motorcycle is in armed mode
Disarm
The system is Disarm.
Remote Transmission
You are transmitting the signal to
control unit
In – Range Indicator
Your are within the remote control
range.
Activate on the Tilt Switch
(Zone 2)
Activate on the Close Loop
(Zone 3).
Activate on the Shock Sensor
(Zone 4)
Activate on the Warn away Trigger
Activate on the Ignition Switch
(Zone 5).
Time Monitor
Alert Alarm
You have set morning call alarm
Count Down Timer
Reminder when time is up for
parking
Power Save Mode
Save the battery power
MEGA 3100 OPERATE
8
Vibration Mode
Remote Control vibrates when the
system is triggered
Button Lock
Disable the transmission function
temporarily
Driver paging / Lose and Found
Someone is paging you in front of
your motorcycle
Low Battery
You have to replace the battery of
remote control.
C. PROGRAMMING OF THE LCD REMOTE TRANSCEIVER:
Transceiver Button Description Operation
(1 second)
LCD screen lamp turns on for
5 seconds.
Press and hold the
button for
1 second, 1 melody sound to
confirm enters.
(3 seconds) Timer Programming Mode.
Press and hold the
button for
3 seconds, 2-melody sounds to
confirm enter.
(5 seconds) Power Save Mode
Press and hold the
button for
5 seconds, 1 melody sound to
confirm enters.
- -
Clear the Flash Icon and Melody
Sound on the LCD Screen Transmitter
Press the button 3 times
within 5 seconds
- (2-second)
Button Lock (
) enable / disable
Press the
button first within 3
seconds press and hold
button
for 2 seconds.
- (2-second)
Melody / Vibration ( ) Mode
Press the
button first within 3
seconds press and hold
button
for 2 seconds.
- F (2-second)
Program Count Down Timer
( )
(10-Minute / 20M / 30 M /1Hour /1.5H /
2.0H)
Press the
button first within 3
seconds press and hold
F button
for 2 seconds.
- (2-second)
Enable / Disable Bi Sound (Bi) While
Pressing Button
Press the button first within 3
seconds press and hold
button for 2 seconds.
- -
(2-second)
Illumination On /Off Press within 3 seconds
1. Screen Lamp ON: Press and hold the button one second, with one melody sound and the LCD
screen lamp will turns on for 5 seconds
2. Power Save Mode For Remote Transceiver: While the power save mode, the LCD
remote transceiver uses “0” current to save the battery power.
Entry: Press & hold the
button for 5 seconds, with one melody sound and
icon on the LCD screen to indicate entry the “power save mode”.
Exit: Press any button of the LCD remote transmitter to exit the “Power Save Mode”.
3. Clear the Flash Icon and Melody Sound: Press the button 3 times within 3 seconds will clear the
flash icon and melody sound on the LCD screen transceiver
4. Stop The Trigger Melody Sound:
While triggering the alarm the LCD screen will alert user through
melody sound and flashing trigger icon, press any button on the LCD remote transmitter to stop melody
sound
only.
5. Button Lock:
It is useful if you want to disable the transmission function of the remote control
temporarily to prevent from any inadvertent pressing of buttons by others. Press the
button first, within 3 seconds press and hold the
( ) button for 2 seconds to activate
or cancel the button lock function, the
icon will displayed on the LCD screen to show
the LCD remote transmitter is on “Button Lock”.
MEGA 3100 OPERATE
9
6. Vibration / Melody Mode:
It is useful when you are in a noisy place and difficult to hear beep sound from the
remote control as the remote control in this mode, vibrates itself if your security system is
triggered.
Press the
button first, within 3 seconds press and hold the ( ) button
for 2 seconds to select the mode of vibration or melody, the
icon will displayed
on the LCD screen to show the LCD remote transceiver is on vibration mode.
7. Enable / Disable Bi Sound While Pressing Button:
It has a short “bi” sound while pressing the button of the LCD screen transceiver
If you want mute the “bi” sound mute always while press button. Press the
button first, within 3 seconds
press and hold the
(Bi) button for 2 seconds to disable the “bi” sound.
8. Low Battery Indication:
When the power of the battery weakens, it has two short “bi” sound and flash
icon while pressing the
button of the LCD screen transceiver.
9. Set Up Fixed Count Down Timer:
1. Press the
button first, within 3 seconds press and hold the F ( ) button for 2 seconds, the
LCD screen will shows
icon and timer (ie. 0:10) ,
2. Press the
F ( ) button again showing next order time on the screen ( ie.0:20), press them again
(ie.0:30)…..and so on.
3. Leave the buttons starting count down then
icon flashes
Note: 1.The count down period is fixed as 10 minutes, 20 minutes, 30 minutes, 1 hour, 1.5 hours and 2
hours maximum.
2.When count down timer showing 0:00 means to turn off the timer.
3. Press
button for real time indication when the timer is counting down.
10. Out Of Range Indication: (See Feature II – 4 Programming.)
The system will automatically check the range every 30 minutes after armed.
1. If user is within the range, the
icon will display on the LCD screen.
2. If user is out of range, it has five short “bi” sounds and the
icon will disappear on the LCD screen.
Note: Programming “Out Of Range Indication” will decrease the life expectancy of battery.
11. Illumination
Illumination for the LCD display can be programmed “On” or “Off”. When programmed “On”, the LCD will
illuminate every time the remote control receives a page or transmits a command.
Press the
button twice, within 3 seconds press and hold the button for 2 seconds. The remote will
beep once for “On”, twice for “Off” and the light will turn on/off with each press.
Note: Programming “illumination “On” will decrease the life expectancy of battery.
D. TIMER SETTING:
Transceiver Button Description Press Transceiver Button
1
Press & Hold the
button for 3 seconds
Timer Setting (Hour)
*Flash digit for adjusting
for – and F for +
Press the button once
Time setting (Minute)
*Flash digit for adjusting
for – and F for +
2 Press the button once.
Alert Alarm Time Setting (Hour)
*Flash digit for adjusting
for – and F for +
Press the button once
Alert Alarm Time Setting (Minute)
*Flash digit for adjusting
for – and F for +
Press the button once Alert Alarm Setting ON / OFF
for OFF and F for ON
3 Press the button once
Count Down Timer Setting (Hour)
*Flash digit for adjusting
(Max.19 hours 59 minutes)
for – and F for +
Press the button once
Count down Timer Setting (Minute)
*Flash digit for adjusting
for – and F for +
Press the button once Count down Timer Setting ON / OFF
for OFF and F for ON
EXIT: Press and hold the button for 2 seconds or leave it for 10seconds, the system will exit the
programming mode.
1. Timer Setting: Example to AM10:30
1. Press & hold the
button for 3 seconds, with two-melody sound and the “Hours” digit flashes for
adjusting.
MEGA 3100 OPERATE
10
2. Press the
or F button to decrease or increase the “Hour” digit until AM10:xx
3. Press the
button once again then the “Minute” digit flashes for adjusting.
4..Press the or F button to decrease or increase the “Minutes” digit until AM 10:30
5. Press the
button for 2 seconds with one-melody sound to confirm exit the timer program mode.
2. Alert Alarm Timer Setting: Example to PM 6:30
1. Press & hold the button for 3 seconds, with two-melody sound and the “Hours” digit flashes for
adjusting.
2. Press the
button twice, the LCD screen will shows icon and “Hours” digit is flashes for
adjusting.
3. Press the
or F button to decrease or increase the “Hour” digit until PM 6:xx
4. Press the
button once again then the “Minutes” digit flashes for adjusting.
5. Press the or F button to decrease or increase the “Minutes” digit until PM 6:30
6. Press the
button once again then icon flashes for alert alarm “ON / OFF” setting
7. Press the
F button to start the “Alert Alarm Timer”, and the “ON” icon will show on the LCD screen.
Press the
button to stop the “Alert Alarm Timer”, and the “OFF” icon will show on the LCD screen.
8. Press button for 2 seconds with one-melody sound to confirm exit the timer program mode.
3. Count Down Timer Setting: Example Set count down timer at 2:30
1. Press & hold the
button for 3 seconds, with two-melody sound and the “Hours” digit flashes for
adjusting.
2. Press the
button 5 times, the LCD screen will shows icon and “Hours” digit is flashes for
adjusting.
3.Press the
or F button to decrease or increase the “Hour” digit until 2:xx
4.Press the button once again then the “Minutes” digit flashes for adjusting.
5. Press the
or F button to decrease or increase the “Minute” digit until 2:30
6. Press the
button once again then icon flashes for alert alarm “ON / OFF” setting
7. Press the
F button to start the count down timer, and the “ON” icon will show on the LCD screen.
Press the
button to stop the count down timer, and the “OFF” icon will show on the LCD screen.
8. Press the button for 2 seconds with one-melody sound to confirm exit the timer program mode.
Note: Maximum is 19 hours.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions.
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
MEGA 3100 OPERATE
11
MEGA 3100 OPERATE
12
Loading...