Page 1
1
MINIMED™ 670G SYSTEM |
CHANGING THE MINIMED™SURE-T® INFUSION SET QUICK REFERENCE GUIDE
START HERE
1
5
2
1 2 3 4
6
3 4
Wash your hands.
Press
. Select Options.
Select Reservoir & Tubing. Select New Reservoir.
Select Rewind.
Remove the infusion set you have been using by
loosening the adhesive and pulling away from body.
Remove the used reservoir from the pump.
Remove from package. Make sure
insulin vial is at room temperature
to reduce the risk of air bubbles.
Pull plunger down to
the amount that you
plan to ll with insulin.
Wipe vial with alcohol. Place
vial on table. Firmly press the
blue transfer guard onto vial.
Push and hold
plunger down.
Plunger
rod
Plunger
Reservoir
Insulin vial
Transfer
guard
FILL RESERVOIR & CONNECT TO THE INFUSION SET TUBING
F
ollow the next steps to ll reservoir with insulin and connect to the infusion set tubing.
Continued on next page
Page 2
2
MINIMED™ 670G SYSTEM |
CHANGING THE MINIMED™SURE-T® INFUSION SET QUICK REFERENCE GUIDE
Remove the infusion set from package.
Press the edges of the set release
connector. With the other hand, pull
the cap o.
Slide the set release
connector into the
set connector.
5
4
1
6
6
7
2
8
3
With your thumb still on the plunger,
ip over so vial is on top. Release
thumb and pull plunger down to ll
with insulin.
Tap the reservoir to move
air bubbles to top of
reservoir. Push plunger
up to move air into vial.
If needed, pull plunger
back down to amount
of insulin needed for
2-3 days.
To avoid getting insulin on the top of the
reservoir, turn vial over so it is upright. Hold
transfer guard and turn reservoir counterclockwise and remove from transfer guard.
WARNING: If insulin or any liquid gets inside the tubing connector, it can temporarily block the vents that allow the pump to properly fill
the infusion set. This may result in the delivery of too little or too much insulin, which could cause hyperglycaemia or hypoglycaemia.
CONNECT RESERVOIR TO INFUSION SET
Y
ou will place the tubing connector onto the end of the infusion set to the lled reservoir.
Gently push the tubing
connector onto reservoir.
Turn clockwise until locked.
You will hear a click.
If you see air bubbles, tap
reservoir to move them to
top. Push plunger just a bit
to move them into tubing.
Twist plunger counterclockwise to loosen
and remove.
5
Continued on next page
Set connector
Set release
Tubing
connector
Sure-T
insertion piece
Page 3
3
MINIMED™ 670G SYSTEM |
CHANGING THE MINIMED™SURE-T® INFUSION SET QUICK REFERENCE GUIDE
3 4
1 2 3
Place reservoir into pump. Select Next.
Select Load and keep
holding
.
When you see this screen,
select Next.
After you see drops,
press
and select Next.
Select Fill and keep holding
until you see
drops at the end of tubing, then let go.
Turn clockwise until you feel
reservoir lock into place.
Drops at end
of tubing
21
LOAD RESERVOIR AND FILL TUBING
Fol
low these steps to load the reservoir and ll the tubing.
PLACE RESERVOIR INTO PUMP
Now place the lled reservoir into the reservoir compartment of the pump.
Select Load Reservoir
from the menu.
Press
to open the menu. If the
pump is locked, you will need to
unlock the pump after pressing
.
Select Next.
Continued on next page
THE BACKLIGHT MAY HAVE TURNED OFF
Press any button to turn the screen back on.
Page 4
4
MINIMED™ 670G SYSTEM |
CHANGING THE MINIMED™SURE-T® INFUSION SET QUICK REFERENCE GUIDE
2
43 5 6
Peel o both pieces of
the paper backing from
the insertion piece.
With one hand, pinch up
skin at prepared site. With
the other hand, insert the
needle straight in at a 90
degree angle.
You do not need to ll
a cannula. Press
and
select Done.
Pull o the needle
guard.
Press adhesive
securely to skin.
Choose an insertion site from the
shaded areas shown here. Wipe with
alcohol or other antiseptic.
Remove paper backing from the set
connector and secure adhesive to skin.
Be sure to place it on an area of your
body that allows for easy disconnecting
from tubing.
1
INSERT INFUSION SET
Next, follow the steps to insert the infusion set into your body
.
Hold infusion set insertion piece by
ipping the plastic wings upwards and
pressing them together.
MiniMed is a trademark and Sure-T is a registered trademark of Medtronic, MiniMed Inc. ©2017 Medtronic MiniMed, Inc. All rights reserved. Medtronic Australasia Pty Ltd. 2 Alma Road, Macquarie Park. NSW 2113. Australia. medtronic-diabetes.com.au 5360-102018
COMPLETE THE INFUSION SET CHANGE
Use the pump to nish the process.
Your infusion set change is now complete!
Loading...