Medtronic MINIMED ONE-PRESS SERTER Quick Reference Manual

Download

Page 1

MINIMED™ 670G SYSTEM |

ONE-PRESS SERTER WITH GUARDIAN SENSOR 3 QUICK REFERENCE GUIDE

INSERTING A NEW SENSOR

Guardian™ Link(3)

MMT-XXXX

Wash your hands and clean insertion site with alcohol.

1) Open sensor package. Pull corner of paper covering to open sensor package.

2a) Hold sensor by plastic

pedestal. Remove sensor

with attached pedestal by holding pedestal only. Place sensor/pedestal on a clean, at surface (such as a table).

4) Detach serter from pedestal. To detach serter from the pedestal, grip serter as shown with thumb on thumb print on serter. With other hand,

place two ngers on pedestal arms, and slowly

pull serter straight up.

Fingers are NOT holding the side buttons.

NOTE: Make sure that the pedestal is rmly on

the table before pulling the serter away.

2b) Tuck adhesive tab. Make sure that sensor’s

adhesive tab is tucked under sensor connector and snaps.

Correct Incorrect

3) Load sensor into serter. Grip serter exactly as shown with thumb on thumb print on serter. Do not hold the side buttons. Push serter down

onto pedestal until base of

serter sits at on table.

CAUTION: Do not detach pedestal from serter in mid-air as this may damage the sensor.

5a) Place serter on body. Hold

serter steadily against your cleaned insertion site, without pushing serter too deeply into skin.

NOTE: Failing to hold serter securely at against

body may allow serter to spring back after pressing buttons and result in improper insertion of sensor.

5b) Insert sensor. Press and

release bump on both buttons at same time.

Correct Incorrect

5c) Hold serter against body.

Continue holding serter

against body for at least ve

seconds to allow adhesive to stick to skin.

Page 2

MINIMED™ 670G SYSTEM |

ONE-PRESS SERTER WITH GUARDIAN SENSOR 3 QUICK REFERENCE GUIDE

5d) Remove serter from body.

Slowly pull serter away from skin, making sure buttons are not pressed.

8a) Untuck adhesive tab.

Untuck adhesive tab from under sensor connector.

6) Remove needle housing. Gently hold base of sensor against skin with one hand. With other hand, hold needle housing at top and slowly pull it straight away from sensor. Dispose of needle housing in sharps container.

NOTE: Apply additional liquid adhesive. You may use an optional adhesive such as Skin Tac™ under the adhesive pad, prior to removing the liner. Allow it to dry.

7a) Remove adhesive pad liner.

Hold sensor in place and gently remove adhesive liner from under adhesive pad.

8b) Straighten adhesive tab.

Straighten adhesive tab so it lies at against your skin, but do not remove adhesive liner yet.

TAPING YOUR SENSOR

emove liner 1 and liner 2.

1) R

2) Apply tape as shown and

press down rmly.

Both sensor and skin are taped.

7b) Press entire adhesive

pad to skin. Firmly press

adhesive against skin and smooth entire adhesive pad so it sticks to skin.

NOTE: The Guardian sensor adhesive is sensitive to pressure. Continue applying pressure on the adhesive to ensure that the sensor remains inserted in the skin for 7 days of wear.

Wide part of tape covers half of sensor base.

3) Remove liner 3 from each side.

Connector and snaps in hole of tape.

4) Smooth the tape.

Page 3

MINIMED™ 670G SYSTEM |

ONE-PRESS SERTER WITH GUARDIAN SENSOR 3 QUICK REFERENCE GUIDE

CONNECTING YOUR TRANSMITTER

1) Connect the transmitter to

the sensor.

NOTE: Wait for green light on transmitter to ash. If green light does not ash, refer to Troubleshooting

section of your transmitter user guide.

2) Remove liner from adhesive tab. Cover transmitter with adhesive tab.

6) Smooth the tape.

NOTE: Check your site regularly. Apply additional

o-the-shelf tape if sensor and transmitter not

secure.

7) This image is an example of Oval Tape applied correctly.

NOTE: Do not pull tab too tightly.

3) To apply 2nd tape, remove

liner 1 and liner 2.

4) Rotate 2nd tape and place tape over transmitter. Press

down rmly.

Wide part of tape covers end of transmitter and skin.

5) Remove liner 3 from each side.

STARTING THE SENSOR

1) Once Sensor connected

message appears, press

This typically takes less than a minute, but may take up to 10 minutes.

2) Select Start New Sensor.

3) The Sensor warm-up started message will

appear. Press then

to clear.

and

4) Warm up... will appear on the Home screen until sensor is ready for the

rst calibration.

Page 4

MINIMED™ 670G SYSTEM |

ONE-PRESS SERTER WITH GUARDIAN SENSOR 3 QUICK REFERENCE GUIDE

CALIBRATING

1) Select Snooze.

2) Pump will display this screen. Test BG and use to calibrate the sensor. See “Calibration” on

page 31 of the Getting Started with MiniMed™ 670G Continuous Monitoring workbook if you

need help calibrating.

3) Once calibration BG is entered, this screen will display. You will begin receiving sensor glucose readings in 10 minutes.

Glucose