Medifab Spex Wonderseat User Manual

User Name:

Serial Number:

User Manual for all SPEX Wonderseat (product code begins with ‘2885’)

WONDERSEAT

USER MANUAL

IMPORTANT CONSUMER INFORMATION NOTICE:

This manual contains important instructions that must be passed on to the user of this
product. Please do not remove this user manual before delivery to the end user.

SUPPLIER: This manual along with Bingo-OT/COBRA Base manuals must be given to the
user of this product.

USER/CAREGIVER: Before using this product, read both SPEX Wonderseat and Bingo-OT/
COBRA Base entire manual and save for future reference.

Revision: Wonderseat 20180411

3

Assembling the Wonderseat

Welcome

Thank you for purchasing the SPEX Wonderseat for use with the Bingo-OT

seat unit. SPEX Wonderseat is a package of posturally supportive

components based on the SPEX technology designed and

developed especially for the Bingo-OT seat unit for use with the

EVO stroller and COBRA Indoor Base.

The safety advice and directions in this manual cannot

cover all eventualities and unforeseen situations that

may occur. It must be understood that common

sense, general caution and care are factors

that cannot be built into this

product. These are factors

which the caregiver must

assume responsibility for.

4

All prescribers and caregivers who use this product should read and understand this manual
and the manual for Bingo-OT/COBRA Base prior to use. The safety of the user is the caregivers
responsibility. It is important to the user and caregivers safety that the products are used correctly,
that they function as intended and all safety aspects are understood. Medifab recommends that
set-up fittings, and adjustments be performed after carefully reading this manual and the Bingo­OT/COBRA Base manual. It is important to consider the user’s positioning, physical limitations and
needs when configuring this product. Consult the user’s health care provider with any questions
regarding the set up and use of this product.

Contact Medifab for assistance with set up and assembly if required. Medifab will also be able to
provide advice regarding the safe use of this product.

Read Before Use

5

Contents

READ BEFORE USE 4

GENERAL INFORMATION 6

DECLARATION OF CONFORMITY 7

WARRANTY 7

BEFORE STARTING 8

WARNINGS AND SAFETY NOTES 10

ASSEMBLING THE SPEX WONDERSEAT 12

Lateral Trunk Supports 14
Pelvic & Arm Support Receivers 15
Head Support 17
Back Support 18
Seat Cushion 19
Hip Belt 20
Shoulder Harness 21
Sandals 22
Extended Footplate Raiser Kit 22
Footplate Cover 24

SETTING UP 25

Seat Depth 26
Pelvic Support 27
Back Support 29
Extended Height Footplate 30
Foot Positioning Sandals Setup 31
Head Support 32
Lateral Trunk Supports 34
Arm Supports/Pelvic Quick Release 36
Tilt in Space/Recline Safety 37
Arm Supports 38
Hip Belt 40
Shoulder Harness 41
Contouring the Back Support 42

CLEANING 43

MAINTENANCE 45

REISSUING TO ANOTHER USER 47

WONDERSEAT SERVICING AND TECHNICAL DATA 49

Disposal & Recycling 50
Environment 50

Symbol Glossary

Warning or Caution ­Consult Instructions for
Use

Manufacturer

Date of Manufacture

Batch Code

Catalogue Number

Serial Number

Consult Instructions for Use

WEIGHT

Maximum weight limit

6

Children with severe neuromuscular impairment are at high risk of developing postural
asymmetries. Early intervention is paramount to promote spinal alignment and avoid the
development of postural deviations. The SPEX Wonderseat has been designed to provide stability
and postural support to allow young children to explore the world while growing healthy. Its unique
adaptable and adjustable features are based on SPEX technology, which allow clinicians to work
towards prevention or correction of postural presentations. It has been specially designed for use
with the HOGGI Bingo-OT seat unit only, with full cooperation with HOGGI GmbH team.

Intended Use:

The SPEX Wonderseat is intended for use in conjunction with the Bingo-OT seat unit and aims
to provide postural support and wheeled mobility to children with disabilities who are partially or
permanently non-ambulatory and limited to a sitting position.

The prescriber must ensure that they are fully familiar with the intended use of the Bingo-OT seat
unit and follow all instructions provided in the Bingo-OT/COBRA Base’s user manuals. It is the
responsibility of the prescriber to ensure that the Bingo-OT is prescribed, setup up, maintained and
used as recommend by the Hoggi Gmbh. This manual along with the Bingo-OT/COBRA Base's
user manuals must be passed on to the user of this product.

All changes made to the SPEX Wonderseat should be noted in the Product Log Form page of this
user manual.

Disclaimer: Medifab takes no responsibility as to the therapeutic eectiveness of our products. Our
claims relate to the ability of the products to provide safe and reliable positioning and seating on
the equipment onto which they are installed.

General Information

7

Declaration of Conformity

Medifab warrants that equipment sold by Medifab will be free of all defects in material
and workmanship for a period of 2 years from the date of purchase. We will not be held
responsible for any damage or injury due to misuse or modification of our products. If any part
of the equipment is found to be defective within the terms and period of this warranty Medifab
will, at its own discretion, repair or replace it.

The SPEX Wonderseat is CE-marked. We verify that it meets relevant European safety
requirements.

The SPEX Wonderseat has been classified as a class 1 product according to the classification
criteria outlined in Annex VIII of the European Union Medical Devices (MD) Regulation
2017/745.

US REP: Medicept 200 Homer Ave Ashland, MA 01721 United States

EU REP: BEO MedConsulting Berlin GmbH Helmholtzstr. 2 D-10587 Berlin

Warranty

8

Before Starting

•Always read the instructions before use. Failure to follow instructions may impair use, impede
function and more importantly, may aect the users or caregivers safety

• Materials and foam
SPEX Wonderseat seat cushion and back support meet the requirement of ISO 7176-16: Wheelchairs

– resistance to ignition of postural support devices.

In rare cases the Neoprene fabric and Lycra fabric may cause skin irritation for people with sensitive
skin. If you experience any irritation of the skin consult with your health care professional.

• Compatibility. The SPEX Wonderseat is only designed to be used with Bingo-OT seat unit.

• Do not add any other accessories other than those supplied by Medifab to this product.

• Weight Capacity

Basket 3kg
Tray 5 kg
User 35kg
Seat Unit size 1 and 2 50kg
Mobility Base size 1 and 2 60kg

Seat unit max load of 50kg comprises of the total weight of the user and additional accessories
attached to seat unit eg tray, Wonderseat components.

Mobility base max load of 60kg comprises of the total weight of seat unit and any other accessories
attached to the mobility base. eg basket.

• Service or repair on the SPEX Wonderseat must only be carried out by a Medifab authorised
service person.

• Service or repair on the Bingo-OT/COBRA Base must only be carried out by a Hoggi GmbH
authorised service person. Any service or repair carried out by any other person will invalidate the
guarantee and Medifab cannot accept any liability for injury or damage thus caused.

9

• The tools required to adjust the SPEX Wonderseat are an 8 and 10 mm ring spanner/socket and
3 and 5 mm Allen keys.

• Ensure SPEX Wonderseat is fully assembled with Bingo-OT seat unit on the Bingo-OT/COBRA
Base before use.

• It is essential SPEX Wonderseat and Bingo-OT with the Bingo-OT/COBRA Base are cleaned
regularly so as not to impede function and to remain hygienic. Refer to the Cleaning and Maintainance
section of this manual.

• Read the instruction manual and be fully aware of all available adjustments.

• The prescriber or caregiver has the responsibility to ensure the product is correctly set up to meet

the user’s needs.

• SPEX Wonderseat is not provided as a sterile product and does not require disinfection before use.

• Prescribers and caregiver(s) should be made aware of the following key sections of this manual;

• Before starting

• Warnings

• Setting up hip belt and chest harness

• Lateral trunk support adjustment (flip away)

• Arm support & pelvic support (removing support to assist transfer)

• Prescribers and caregiver(s) should be made aware of the following key sections in the Bingo-OT/
COBRA Base manual;

• Common information

• Safety instruction

• Delivery and preparing

• Adjusting and adaptation

• Accessories

• Transport

• Maintenance/service and repair

• Technical date

10

Understandin your SPEX Wonderseat

• To avoid injury, read, understand and follow all instructions and warnings in this manual before
installing and using the SPEX Wonderseat on Bingo-OT. Please also read the Bingo OT/COBRA
Base user manual to make sure you use both the products as recommended.

• There are hazards associated with the use of SPEX Wonderseat with Bingo-OT/COBRA Base.
Please read the Warning sections in both the manuals. You are responsible for the safety of the
user. The safety of the user could be aected if you do not follow the instruction in this manual
and Bingo-OT/COBRA Base manuals.

• The prescriber or caregiver has the responsibility to ensure the product is correctly set up to
meet the user’s needs.

• The SPEX Wonderseat range has been specifically designed for Bingo-OT/COBRA Base only.
Do not use SPEX Wonderseat on any other mobility/stroller frames.

• Trays must not be loaded with objects heavier than 5 kg.

• Never lift or move the Bingo-OT by grasping the accessories.

• A poorly fitted head, lateral trunk and/or pelvic support can aggravate postural problems and
the overall safety of user.

• Never leave the user unattended in the SPEX Wonderseat, even for the shortest time.

• The caregiver must know how to fit, adjust and release the buckles and clips on pelvic and
shoulder harness and jackets.

• Never use the SPEX Wonderseat upholstered parts without their covers. Care should be
exercised near open flame or burning cigarettes. Using the back support without its cover
increases the risk of flammability and skin damage.

• Never exceed the weight capacity of your Bingo-OT/COBRA Base as specified by the Hoggi
GmbH.

Before usin your SPEX Wonderseat

• Ensure any loads added to the tray or any other accessories do not exceed the base's total
weight limit.

• Never use your SPEX Wonderseat or the Bingo-OT/COBRA Base if any hardware is missing,
malfunctioning or broken. Seek qualified assistance with any repairs, replacements or
adjustments.

• The locking mechanism for the removable pelvic/arm support and the lateral trunk support
must be correctly locking at all times. If it stops locking do not use the product.

• Hip belt/shoulder harness strap ends can be trapped in the tilt mechanism and can impede
the engagement of the locking pins on the Bingo-OT/COBRA Base. In such case the seat could
fall o the mobility base. Shorten excess strap ends on accessories so they cannot be trapped.
Ensure the seat is fully engaged by pulling the seat sharply forward and checking that locking
pins are fully engaged and haven't moved.. Check that the locking pins are completely engaged.
Please refer to Bingo-OT/COBRA Base manual for further information.

Warnings and Safety Notes

WARNING

RISK OF ACCIDENT, INJURY, PAIN OR DEATH IF WARNINGS ARE NOT HEEDED

11

Usin your SPEX Wonderseat

• Ensure the child’s arms are raised above the arm supports when raising the backrest from
recline or remove the supports prior to raising the backrest angle to protect the child with
potential pinch points with the mechanisms, lateral trunk, pelvic supports and arm supports.

• Ensure the child’s fingers are clear of the base of the backrest or it’s tubes when reclining
because there is a potential crush point between this and the cushion.

• When using the hip belt or shoulder harness, ensure the position of the harness is anatomically
correct. Ensure the pad is not impeding on the throat.

• Do not leave the user exposed to the sun. The canopy/sun-hood on this product will not give
the user protection from the harmful rays of the sun.

• Care must be taken when transferring a user from the SPEX Wonderseat. The user may fall
from the stroller and injure themselves when supports are removed.

• Secure the user with all the straps provided as soon as the transfer is complete.

• Ensure the child’s fingers and clothes are well clear of the tray receiver when re-engaging the
tray table.

Adjustin your SPEX Wonderseat

• Take care when tilting the seat, ensure that the child’s arms and clothes are clear of the rear of
the arm support and far enough forward to keep clear of the stroller’s tubes.

• Be aware of the pinch points. Ensure all body parts are kept clear during these movements and
adjustments.

• Ensure the straps are adjusted for the user and for changes of clothing. Ensure the straps are
fitted under the pelvic support and fitted snugly to ensure correct posture and safety.

• Ensure the child’s fingers and clothes are well clear of any slots at all times, especially when
making adjustments to the supports or tilting/reclining the seat.

• Keep all fingers and clothes away from any moving mechanisms or adjusting components to
avoid potential pinches and crushes.

• After making any adjustments, ensure all fasteners and knobs are firmly tightened again.

• When removing the pelvic/arm supports or swinging away the lateral trunk supports, ensure
the user is supported by a carer to prevent the user from falling out of the product.

12

Assemblin the Wonderseat

Assembling the SPEX Wonderseat

1. Head Support

2. Back Support

3. Lateral Trunk Supports

4. Arm Supports

1

2

Componentry

3

4

5

6

7

5. Pelvic Supports

6. Seat Cushion

7. Footrest Plate

13

Assembling the Wonderseat

Remove all the packaging and check that you have received all the parts you ordered.

Tools required

Tools required to assemble the Wonderseat on to a Bingo-OT/COBRA Base are an 8 and 10 mm
ring spanner/socket and 3,4 and 5 mm hex Allen keys.

SPEX Wonderseats are prescription and over the counter medical devices.

Installation and adjustment of your SPEX Wonderseat should be performed only by an authorised
dealer, qualified therapist or seating technician.

Before assembling the SPEX Wonderseat onto the Bingo-OT, it is essential that you have read the
Bingo-OT/COBRA Base manual and assembled the Bingo-OT/COBRA Base first.

WARNINGS

1) Installation and adjustment of your SPEX Wonderseat should be performed only
by an authorised dealer, qualified therapist or seating technician.

2) Ensure children do not play with packaging material. Plastic bags can be
dangerous. To avoid danger of suffocation keep all plastic bags away from babies
and children.

Unpackin

Assembling the Wonderseat

14

Remove the wing-nut (A) and move the cup square bolt from the outer
Back support slot to the inner Back support slot.

A

B

Align the rubber pad (C) on the inside of the Back Support with lateral
trunk strength plate and insert the screws with spring and flat washers
from the rear of the Back support.

Lateral Trunk Supports

C

Insert the bolt through the single hole of the lateral trunk strength plate

(B) and thread on the wing-nut to hold in position.

FIG 1

Assembling the Wonderseat

Feed the pair of screws through the rear of the lateral trunk strength
plate, Bingo backrest and thread into the lateral trunk clamp plate.
Repeat the above steps on the opposite side of the backrest secure
all fasteners tightly. Undo the wing-nuts a few turns to ensure that the
upper backrest smoothly adjusts up and down. Secure all fasteners
tight

Pelvic & Arm Support Receivers

Remove seat unit from Bingo-OT/COBRA Base as detailed in the
Bingo-OT/COBRA Base manual. Place the seat unit on its side. Leave
in this position until one side of the new hardware has been assembled
to ensure internal fixings do not slide around. Remove front and
back seat pan mount cup square bolts and discard while placing the
washers (D) to one side for reinstall.

Removin Existin Tray Mount and Seat Pan Cup
Square Bolts

Undo and place to one
side the three sets of
screws and washers
(E), (F) that mount the
existing Bingo-OT/
COBRA Base tray mount
receiver along with the
inner threaded plate (G).

E

F

D

G

D

D

Note, the lateral trunks come in le and right pairs. For correct
posioning ensure the quick release buon (D) is facing outwards
and below the bar clamp

FIG 2

D

E

F

G

B

Assembling the Wonderseat

16

*Note the posion of the internal frame nut

(J)

may have moved
during disassembly and will require the seat unit to be lted forward/
backward to relocate it.

H

I

Align slot of the replacement mounting bracket (H) with the upper
front slot of the Bingo-OT frame (I).

Note, ensure that the red quick release lever (P) is facing forward
with slide rail (M) placed on seat pan to ensure it is being installed on
the correct side of the seat unit.

Insert the original button head screw into flat washer (E) and assemble
into the frame nut (J).

E

J

K

L

Insert the screws (F) with the washers (flat washer contacting the
mount) through the lower bracket holes of the side mounting bracket
(K), the Bingo-OT slots (L) and reattach the threaded plate (G) (ref FIG
2 for fastener assembly order).

Loosen the rail adjustment screw (H) to allow the seat rail mount holes
to align with seat pan mount holes.

F

H

G

Align front and rear rail mount holes with the corresponding outer
seat pan holes and install the cup square bolts, flat washers and nylon
nuts.

Remove the new cup sqaure bolts and nuts from kit (A-01459) and
reuse the washers (D) from initial tray mount removal.

Ensure the fasteners are tight and at least two threads are visible pass
the blue nylon ring in the nut.

Repeat process for the other side.

Installin Side Mounts

Align the two lower holes of side mounting bracket (K) with the two
slots within the frame (L).

*Note, be sure not to fasten into same slot twice.

M

N

P

Assembling the Wonderseat

17

Head Support

Remove button screws, flat washer and Nyloc nuts from the Bingo-OT
frame and discard.

Removin existin fixins from frame

Remove the 4 screws and spring washers from the head support
mounting block noting that the longest screw (B) is positioned in the
lower right of the mount.

Installin the Head Support

Align the mounting block with the rear of the back-support shell, then
install the spring washers and button screws from the front ensuring
that the longest of the bolts with washer (B) is returned to the lower
right corner mount hole*.

Ensure that all fasteners are tight with spring washers fully
compressed.

B

*Note, for increased accessibility, raise the backrest up by loosening
the wing-knobs on the back.

FIG 3

Assembling the Wonderseat

18

Back Support

Remove the upper Velcro strips from the rear of the Back Support.

Attachin Velcro Strips to Frame

The Back Support can now be fitted to the backrest.

B

A

Peel o the film backing and press
firmly onto the surface in the following
positions*:

1 × horizontal strip, mounted on the Bingo­OT seat top tube (A)

2 × vertical strips, mounted approximately
20mm inside the Back support slots (B)

*Note, ensure that the surface the

Velcro is applied to is completely clean
and dry.

*Note, ensure that the Back Support rear panel and upper Back
Support ap are pressed rmly onto the Velcro strips.

Assembling the Wonderseat

v

v

19

Seat Cushion

Remove the Velcro strips from the underside of the seat cushion.

Peel o the film backing and press firmly onto the
surface of the seat-pan in the following positions: *

1 x strip applied to the front edge of seat pan (A).

2 x strips applied symmetrically on seat pan (B)
approximately 50 mm from front edge of seat pan
and 20 mm inside central seat pan bolts.

Attachin Velcro Strips to Frame

The seat cushion can now be fitted to the seat pan.

*Note, ensure that the cushion base and front ap are pressed rmly
onto the Velcro strips.

B

A

WARNINGS

Ensure the child’s ngers are clear of the base of the backrest
or it’s tubes when reclining because there is a potenal crush
point between this and the cushion.

20

Assembling the Wonderseat

1`

Hip Belt

Installin 4-Point Hip Belts
Rear Straps or 2-Point Hip
Belts

Insert strap through the rear slot of
the stroller frame (1).

Feed the strap through the metal
harness Triglide (2).

Feed the strap back though the
harness Triglide to lock in position

(3)

Repeat for other side.

1

3

Installing 4-point Hip Belts Retainer Straps

Attach the rear straps in the same manner as the 2-Point Hip Helt
method (above) then insert the front straps through the slots in the
arm support receiver.

Feed strap through Triglides as in steps (2) and (3) for the 2-Point Hip
Belt.

2

Adjust the length of the hip belt D-rings (C) so that they are
approximately the same length from buckle. Repeat for other side

C

21

Assembling the Wonderseat

Shoulder Harness

Installin Lower Straps in Back Support

Feed the straps through plastic
Triglide as shown in steps 2 and 3
Hip Guide section.

Repeat for other side

Pull up the Back Support flap and remove Bingo-OT shoulder harness clip
thumb nut (A) and remove the buckle (B). Move the screw (C) from the
outer to the inner backrest hole and place through the lowest webbing hole
of the quick release buckle short strap (D). Tighten on the thumb nut so it
is fully tight.

Feed the long straps buckle through the fabric Back Support guide (E) and
click into place. Repeat for the other side.

Insert the end of the lower strap through the lower backrest slot.

Installin Upper Straps

A

B

A

D

C

E

Assembling the Wonderseat

22

Sandals

Unpack sandals and place metal and plastic washers on the wing bolt
in the order indicated.

B

A

Align the sandal slot nut (B) with the wing bolt (A) and tighten wing bolt.

Extended Footplate Raiser Kit

Loosen the wing-nuts, then slide
the complete footplate unit o the
frame tubes.

C

Loosen and remove the countersunk screws
(C), washers and nuts that secure the footplate.

Assembling the Wonderseat

23

Unpack extended footplate raiser kit (A-01408) and attach the 4
spacer tubes (D) to the underside of the footplate with the original
countersunk screws.

D

F

Place the footplate with spacer tubes onto the Bingo-OT footplate
mounting bracket (E). Hold the footplate angle locking plate (F) on
the underside of the bracket, align the slots with the spacer tubes
and install the 4 sets of screws, spring and flat washers in the order
indicated in the above exploded view. Fully tighten all screws.

E

FIG 4

24

Assembling the Wonderseat

Footplate Cover

The footplate cover provides a soft
surface for when the user is not wearing
shoes.

Peel o the film backing and press the Velcro strips firmly onto the
surface in the following positions*:

2 × strips, The first (A) mounted approximately 20mm from central
front of footplate and the second (B) midway between the 4 footplate
mount screws.

*Note, ensure that the surface the Velcro is applied to is completely
clean and dry.

B

A

Attachin Velco Strips to Footplate

Attachin Cover

Place the cover over the footplate while ensuring the bracket clearance
opening is underneath the footplate. Press the cover firmly onto the
Velcro.

25

Assembling the Wonderseat

SETTING UP

The prescriber or caregiver has the responsibility to be aware of all the available adjustments and
ensure the product is correctly set up to meet the user’s needs.

Medifab recommends that a formal written record is maintained for all the setups and maintenance
checks. A product log form is available at the end of this manual.

Before placing the user in the seat, ensure the following adjustments are made. If the caregiver
has any questions or if additional information is required, contact the user’s health care provider or
Medifab.

The set up may require one or more than one of the following tools:

• 3 mm Allen key or equivalent

• 4mm Allen key or equivalent

• 5 mm Allen key or equivalent

• 8 mm spanner or equivalent

• 10 mm spanner or equivalent

26

Settin up the Wonderseat

.

Seat Depth

Apply the Bingo-OT/COBRA Base foot brake and tilt the backrest
back to provide access to rearmost fastener (A). Loosen a few turns
along with the remaining 4 fasteners indicated in green above. Repeat
process on remaining 5 fasteners on the other side of the Bingo-OT/
COBRA

Note, refer to Bingo-OT manual for lt method.

A

A

Tilt the seat unit forward until an audible click is heard to indicate the
tilt is locked in position. Grasp front of seat pan and pull or push to
lengthen or shorten seat depth. Once desired seat depth has been
obtained, re tilt to provide access to all screws and firmly secure all.

WARNINGS

Do not adjust the seat depth whilst the user is seated in
the SPEX Wonderseat.

WARNINGS

Ensure the seat unit is being held secularly when
loosening screws.

FIG 5

27

Settin up the Wonderseat

.

.

E

Pelvic Support

Pelvic Heiht

Loosen the front (C) and/or rear (D) pairs of
screws and slide the U-bar as required.

Fully re-tighten the 4 screws.

Note 1, you may need to unzip the pelvic
pad cover to have access to the rear pair of
screws.

Note 2, maximum range of height
adjustment occurs when both the front and
rear pairs of screws are adjusted.

Note 3, if access to rear screws (D) is
dicult, then the front screws (C) may have
to be loosened rst or alternavely use the
arm supports quick release.

Pelvic Width and Anle

Loosen the same 4 screws as above and
adjust the angle of the U-bar (E) and pelvic
pad (F) to the desired position.

Re-tighten the 4 screws and re-zip pelvic cover.

Note 1, if access if dicult then the quick
release opon may be required.

Note 2, if plate depth is also to be altered,
don’t fully ghten rear screws and proceed to

F

C

D

28

Settin up the Wonderseat

.

.

Pelvic Depth

There are two methods of achieving depth adjustment of the pelvic
supports.

D

Unzip pelvic guide cover to provide
access to the pair of Pelvic Support
plate screws (D). This allows the
Pelvic Support pad to slide forward/
back to desired position. Once
desired position has been achieved
then re-tighten screws and re-zip
cover.

2) Side Support

Tilt the seat back to provide
access to all 4 of the side mount
adjustment screws and loosen.
This will allow the side support
including pelvic support to be slid
forward/backward.

Once the desired position has
been obtained, re-tighten all
screws.

Note, modifying this posion will
also modify the tray and arm
supports posions.

WARNING

1) To reduce the possibility of arm entrapment, do not use Wonderseat without the hip guides in place

2) Ensure the child’s fingers and clothes are well clear of the tray receiver when re-engaging the tray table

1) Pelvic plate

29

Settin up the Wonderseat

.

.

Loosen the pair of wing-nuts (A) and 4 lateral trunk mount screws (B)
a few turns and raise or lower the height of the upper back support as
required.

Re-tighten the screws and wing-nuts

Note, Ensure the maximum height as specied in the technical
secon is not exceeded

Back Support

If the recline handle (C) position on the rear back support cross tube
contacts the head support mount when the backrest is in the lowest
position then it can be moved sideways to provide clearance.

Loosen recline handle mount screw (D) and slide sideways just enough
to provide sucient clearance.

C

E

D

WARNINGS

1) After repositioning ensure that the cable recline cable (E) does not interfere with recline/tilt function.

2) Ensure shoulder straps are loose when adjusting the height of Back support or choking may occur.

A

B

Heiht Adjustment

30

Settin up the Wonderseat

.

.

Extended Height Footplate

Step 2.

Position the footplate to

the required angle.

Step 3. Slide the locking plate
to press against the tubes and
tighten the screws to fix the
footplate angle.

Anle Adjustment

1

2

3

Step 1. Loosen the pair of screws that hold on the locking plate (B).

Loosen the pair or wing-bolts.

Slide footplate to required height,

then fully re-tighten wing-bolts.

Heiht Adjustment

B

WARNINGS

After repositioning ensure that the cable recline cable (E)
does not interfere with recline/tilt function.

WARNINGS

Ensure the child’s fingers and clothes are well clear of the
central mechanism when adjusting the angle of the footrest
because there are several severe pinch/crush points.

Note 1, this leg angle adjustment is not described within this
manual however can be found within the HOGGI Evoluon manual.

31

Settin up the Wonderseat

.

Foot Positioning Sandals Setup

Attachin to User

Foot Width and Anle Adjustment

The sandals can be independently adjusted for a wide range of width
and angle settings.

Loosen the wing-bolts on the underside of the footplate, slide and/or
rotate the sandals to the required position and re-tighten.

.

Undo the front Velcro straps, position the users feet into the sandals
and re-criss cross the Velcro to secure the feet.

WARNINGS

The footrest plate is not to be stood on and is for seated
use only.

32

Settin up the Wonderseat

.

.

Head Support

Heiht-Two Methods of Adjustment

1) Stem Adjustment

2) Plate Adjustment

E

Undo clamp handle (B) to raise or lower the head support using the
stem (A) adjustment. Once the required position is achieved then fully
re-tighten clamp.

Note, at the lowest backrest posion the clamp handle may be
prevented from fully turning because of insucient clearance with
the Bingo-OT seat unit. If this occurs ghten the handle as much as
possible then push buon (D) and pull handle (C) which allows the
handle to slip anclockwise without loosening. Push handle back in
for further ghtening.

WARNING

1) Do not adjust whilst the child is seated in the SPEX
Wonderseat

A

B

Further head support height can be achieved by adjusting the position
of the ball mount (F).

Unzip the cover and fully undo the 4 head support mount screws (E).
Lift the head support plate to align with next set of screws for 25 mm
of height increase or the lowest set of screws for 50 mm of height
adjustment. Replace and fully re-tighten the screws.

WARNING

At max head
support height the
plasc bung will
be below clamp.

Do not raise any

higher.

F

FIG 6

C

D

33

Settin up the Wonderseat

Anle Adjustments

WARNING

Ensure that if the user is in the seang system that the
head is fully supported during adjustments.

The Wonderseat head support uses a two joint ball and socket system

that allows a large range of motion. All adjustments can be made by

loosening the 6 bolts with a 10 mm spanner. Once making the required

adjustment ensure that all bolts are fully tight.

34

Settin up the Wonderseat

.

.

Lateral Trunk Supports

Swin Away

Pull back the lateral trunk cover (A) to
reveal the quick release slide button (B)
and slide forward. This allows the lateral
trunk to be swung out for clearance
during transfers. Ensure to do up the
cover in swing away position as the
Velcro can damage the Back Support

B

A

Heiht

This method of height adjustment allows the lateral trunk height to be
set independently of the lateral trunk width/angle.

Loosen the two cap screws a few turns (C) as well as the wing-nuts
(D) and then move lateral trunk to the required height. Fully re-tighten
screws and wing-nut.

Note, to avoid backrest height moving perform this adjustment one
lateral trunk at a me

C

D

WARNING

1) Take care when releasing the lateral trunk swing away ensure there is no lateral
trunk load on it because your nger may get crushed on the backrest tubes

2) Keep ngers clear of the inside of the lateral trunk swing away when re-locking
because there is a potenal pinch point with the hinge angle closing

35

.

.

Anle

Loosen the silver lateral trunk clamp screws (E) a few

E

Adjust the Z-bar and the pad until the desired width has been achieved.
Then tighten up the screw while holding in the required position.

Settin up the Wonderseat

.

Loosen the 4 screws (E) and (F) to provide a wide
range of pad tilt, width and height adjustment.

Fully tighten all screws once complete.

.

Depth

E

Pull back cover, loosen the screws (E) a few turns and slide the plate to the
required depth. Fully re-tighten screws.

Axial and Pad Adjustment

F

36

Settin up the Wonderseat

Arm Supports/Pelvic Quick Release

The arm and pelvic supports can be quickly removed by lifting the
quick release lever. This greatly aids in quick transfers or provides
greater access to adjustment screws if required.

Note, The lateral trunks may have to be in swing away posion to
allow clearance for quick release.

WARNINGS

1. Ensure all fingers and clothes including the users are clear of the potential pinch points.

2. When returning the arm supports/pelvic unit to the quick release receiver ensure that there is an audible
click to signify it is fully engaged.

3. Ensure the child’s fingers and clothes are well clear of the arm supports receiver when re-engaging the
arm support/pelvic supports.

37

Tilt in Space/Recline Safety

Please refer to the Bingo-OT/COBRA Base manual for instruction
on how to use the strollers 45° tilt in space feature.

WARNING

Severe pinch points. Ensure the child’s limbs, head and fingers are inside the seat when tilting and reclining,
paying particular attention to the areas highlighted above. Always tilt and recline the seat very slowly.

38

Settin up the Wonderseat

Note 1, to alter the arm supports depth, slide the arm support to it's
fully wide posion to enable forward/back movement as indicated
below. The arm supports can be removed via the quick release
for forward/back adjustments. It is recommended that this be
done inially to familiarise caregiver/therapist with the method of
adjustment.

.

Arm Supports

Width, Anle and Depth Adjustment

All typical arm support
adjustments can be made by
loosening the screws indicated
to the right.

The upper green pair of screws
control the arm supports angle,
width and depth and can be
accessed by unzipping the
cover.

The lower blue pair of screws
allow the height of the arm
supports to be adjusted.

Unzip the arm support cover to provide access to the pair of screws
under the arm support plate then loosen the screws enough to allow
the arm support to be moved freely.

Make the necessary modifications to the width (A)

1

, angle (B) or

depth (C) 2 of the arm supports then re-tighten the screws fully.

A

B C

Note 2, the depth of the arm supports can also be modied by
altering the side support depth plate (G) as described in the Pelvic
adjustment secon. However it is important to note that doing so
will also modify the pelvic posion and thus will also require it to be
checked/modied.

To reduce the possibility
of arm entrapment
minimise the gap
between the rear of the
arm supports and the
back support.

FIG 7

FIG 8

G

39

Settin up the Wonderseat

E

D

.

Loosen the pair of screws
on the arm support height
bracket, raise to required
height then re-tighten fully.

Heiht Adjustment

Extended Width Arm Supports

It is possible to provide a greater width arm supports position
than standard by inverting the arm supports height bracket (F).
It is important to note however that the extra wide position will
not allow the seating system to be used in the reverse position
as it doesn't have sucient clearance with Bingo EVO frame.

Remove the arm supports/pelvic with the quick release.

1) Remove the screws (blue FIG 9) that secure the arm supports
height bracket (F) with the washers, T-nuts and plastic spacer block (E)
and place to one side for re-installation. Rotate this bracket and arm
support 180° and reattach spacer block with fasteners in the order
they were removed.

2) Unzip the arm support pad cover and remove arm support mount
screws (green FIG 11) with washers, rotate the arm support so it is now
forward facing and replace all fasteners and washers in the order in
which they were removed. Set arm support to the desired position, fully
re-tighten all fasteners and re-zip cover.

1

2

FIG 10

FIG 11

F

FIG 9

40

.

Settin up the Wonderseat

Position the user in the seat, then fasten the buckle (A). Tighten the

wide main strap, (B) then the narrow retainer strap (C) while keeping

the buckle central. Check and adjust if required for a comfortable

fit. When properly adjusted and the hip belt is tightened, it should fit

snugly so that the user's pelvis is secure. Tighten the D-ring pulls (D)

until all slack is removed and the pads under the buckle are touching.

If adjustment to the length is necessary to achieve a correct fit this can

be done using the belt end fittings.

Ensure:

(1 ) Comfort - check areas of irritation.

(2) Correct operation - of buckle and adjustment straps.

(3) Bingo-OT seat should be moved through full range of motion,

including tilt, and recline -to check for interference.

Hip Belt

WARNINGS

1. Ensure there is at least a two-finger gap between the user and the hip belt, this will ensure the hip belt is not
too tight.

2. Poorly fitted hip belt may allow the user to slide down the seat which could cause asphyxiation by the straps.

3. Check that the hip belt goes under the pelvic support and that it fits snugly at all times to maintain a correct
seating position.

4. Contact Medifab and/or the user’s health care provider, if you are not sure how to use the Hip Belt. Do not use,
if the straps are damaged or not firmly secured.

5. Keep the straps clean, as caked-up webbing will be dicult to adjust.

6. Inspect straps frequently to ensure the straps have not worked loose

7. Do not allow the user to undo the buckle. If the user is able to undo the buckle contact the user’s health care

provider for guidance on preventing the user from undoing the buckle, as this may be dangerous.

A

User Set-Up

B

D

C

41

.

Settin up the Wonderseat

Shoulder Harness

User Set-Up

E

F

G

1) DO NOT use if the user is not wearing a correctly installed, fitting and fastened Hip Belt.

2) DO NOT use without first properly fitting & fastening the Hip Belt. Risk of choking occurs if the pelvis is not
stabilised correctly.

3) This harness is designed as a positioning device in wheelchairs only. DO NOT use as a transportation safety
restraint (including in vehicles), or in any other application where its failure could result in injury. Misuse of the
SPEX harness is unauthorised and unsafe.

4) Any portion of the harness crossing the chest must be positioned suciently away from the user's neck.

5) The harness should be installed/fitted by a qualified technician/clinician only. Have your seating specialist
demonstrate correct adjustment/use.

6) The height of the backrest should be similar or slightly above the height of the user's shoulders.

7) Should the harness be accidentally released, the user may fall forward. Do not leave the user
unattended at any time while using the shoulder harness if their cognitive abilities or movements
could lead to accidental release. Ensure all caregivers know how the harness is unfastened as failure
to do so could delay emergency release if necessary.

WARNINGS

Prior to adjusting the shoulder harness, first position the user in the
seat, stabilise the pelvis and fasten the hip belt. Position the shoulder
harness on the user and fasten the buckle (E). Tighten the lower straps
(F) to stop the harness “riding” upwards. Pull the D-Rings (G) on the
shoulder straps to tighten the harness to fit comfortably around the
user while ensuring not to over-tighten. Adjust straps to ensure best fit.

Ensure there is no rubbing on shoulders or neck, if so, reposition so
that the harness comfortably supports them without rubbing. Check
overall operation of the tension straps and buckles. Ensure that there is
no interference with other devices such as feeding tubes, arm support,
accessories, or seat tilt mechanisms. Should there be interference,
adjust harness to prevent this.

42

.

Settin up the Wonderseat

The SPEX Wonderseat Back Support has been designed to
accommodate postural asymmetries and adapt to dierent
morphologies. This guide shows how the inner section of the SPEX
Wonderseat Back Support can be contoured. Each cube compartment
contains 2 cubes. These may be removed or added as required with a
maximum of 5 cubes per compartment.

Note 1, an extra set of 10 rmer cubes are also provided with each
back support.

Note 2, the back support and the contouring foams can be kept
and reissued to another user as per the reissue secon within this
manual.

Note 3, record the number of cubes used in each pocket for
reference.

Contourin the Backrest

Unzip Back Support cushion outer cover, release the 2 Velcro tabs (B)
and lean the user forward (depending on user capabilites) to remove
the inner contouring section of the Back Support (A) (the cover will
remain secured to the backrest) and replace with pillow. You can now
remove or add layers of contouring cubes to (C) suit the users needs.

Now the contouring section can be changed to suit the users posture.
Once finished, remove the pillow and reinsert the inner contouring
section.

Lean the user back.

Contouring the Back Support

WARNINGS

1. Two people are required for this adjustment. Before doing this adjustment, retrieve a soft head
pillow or similar to replace Back Support inner section while it is being modified.

2. The second person must remain with the wheelchair user to support them and keep them safe
from falling.

3. Ensure the user has the hip belt fastened.

4. The cubes must always face the rear of the Back Support.

C

B

A

43

Settin up the Wonderseat

For any questions regarding cleaning procedures, contact your authorized SPEX Wonderseat
Seating dealer. The expected lifetime of the Wonderseat hardware is 5 years and 2 years for
the upholstery.

For spot cleaning Medifab recommends using AHP (Activated Hydrogen Peroxide) disinfectant
wipes. The disinfection product must be used as per the manufacturers instructions. Medifab takes
no responsibility for the eectiveness of the disinfection process.

Please also refer to Bingo-OT/COBRA Base manual for Maintenance/Service and Repair.

Cleanin the SPEX Wonderseat Back Support

Back support Outer Cover

• Remove cover by carefully pulling from the Velcro fixing. Locate zip on the cover and unzip

• Remove the inner foam section and turn cover inside out

• Zip cover closed to avoid snagging

• Machine wash in warm water (40°C)

• Drip or tumble dry on low heat

• Do not Iron, Bleach or Dryclean

• If chemical cleaners are used, covers must be rinsed thoroughly with water to
remove all chemical residue and left to dry completely before reuse

• Check the cover for tears and excessive wear and replace if ripped, torn or otherwise
not fully functional

Once completely dry, re-insert the inner foam section into the cover and attach to the
Bingo-OT backrest. Please note, for the SPEX Wonderseat Back Support, the contouring
foam inner section has to go back in the correct way. Ensure the flat surface is facing
towards the user, and the cube section is facing the shell. Once the foam is secured inside
the cover, zip cover closed.

Foam Inner

The Back Support foam inner is not designed to get wet in any way, as this will greatly reduce its
life. If soiled, Medifab recommend replacing the foam inner. If foam accidentally becomes wet, dry
thoroughly before replacing inside the cover.

Medifab recommend the purchase and use of an incontinence cover (which protects the
foam inner and can be washed and sanitised).

Cleaning

44

• Remove the cover from the foam base and turn inside out

• Machine wash in warm water (40 °C)

• Drip or tumble dry on low heat

• Do not iron. Do not dry-clean. Do not bleach

• If chemical cleaners are used, covers must be rinsed thoroughly with water to remove all

chemical residue and left completely to dry before reuse

• Check the cover for tears and excessive wear and replace if ripped, torn or otherwise not

fully functional

• Fitting the cover after washing must be done correctly. Ensure the back of the cover

matches up to the back of the foam base

Foam

• Keep dry

• Check the foam base regularly to ensure good foam consistency

• If it accidentally becomes wet, dry thoroughly before fitting the covers

Incontinence Cover

• Hand wash only

• Do not use bleach or other strong cleaners

• Do not tumble dry

• Failure to use this cover may reduce the life of the cushion

Pelvic, Arm Supports and Head Support

Covers

• Machine wash in warm water (40 °C)

• Do not iron. Do not dry-clean. Do not bleach

Hardware

Hardware may be wiped clean with mild detergent and water. Dry thoroughly after wiping. If
you have any additional questions regarding cleaning procedures, please contact your authorized
SPEX Wonderseat dealer.

Wonderseat Cushion

Outer Cover

45

Maintenance

Daily Checks

Weekly Checks

• Check the hip belt and/or shoulder harness’s are securely fitted to the seat or side support

mounts

• Check the footplate angle and height is secure and tight

• Check all the upholstery for wear and tear

• Check all the adjustment levers and knobs are in place and secure

• Check head support is locked firmly in position

• Check arm supports are locked firmly in position

• Check pelvis supports are locked firmly in position

• Check lateral trunk supports are locked firmly in position

• Check back support is locked firmly in position

• Check head support mount bolts are secured tightly with spring washers fully compressed

• Check arm supports quick release allows arm supports/hip guide unit to be remove easily and

click back into place freely

• Check lateral trunks swing away freely when quick release button is disengaged and lateral

trunk clicks back into place easily

46

• Check the hip belt and/or shoulder harness’s are securely fitted to the seat or side support

mounts and functioning correctly

• Check the backrest, pelvic, footplate, head support, lateral trunk and arm supports are secure

and tight

• Check all the straps for fraying and missing or broken buckles

• Check all the upholstery for wear and tear

• Ensure the quick release arm supports latches and swing away lateral trunk bracket are all

locking

• Check lateral trunk, head support, pelvic and arm supports are all functioning correctly and are

secure and tight

• Replace any missing or worn fasteners/adjusting levers and knobs

• Check the overall structure of the Bingo-OT seat and mobility base unit for any signs of fatigue

or damage. Also refer to the guidance given in the Bingo-OT/EVO Manual.

• Check the Bingo-OT and mobility frame for wear and tear, splinters or breaks

• Check for signs of stress or cracking. If any stress/cracks are found these parts must be

condemned and replaced immediately

WARNING

1) These maintenance checks apply only for the Wonderseat accessories. For
Bingo-OT seat unit, EVO stroller and COBRA HILO base checks please refer to the
appropriate HOGGI manuals for maintenance checks.

2) If a fault is found with any part of the Wonderseat, do not use the product until the
fault is rectified. Contact Medifab customer service department or your local dealer
immediately for guidance.

The frequency of the six-monthly check is only a minimum and should be adjusted depending on
the environment in which the equipment is used. We recommend you maintain a record by filling in
the product log form within this manual.

Medifab recommends that all fasteners be checked for wear, such as loose bolts or broken
components every 6 months. Loose fasteners should be re-tightened according to the
installation instructions. Contact your authorised SPEX Wonderseat supplier immediately to
replace any broken components. Do not continue to use the system after identifying loose
or broken components.

6 Monthly Check

47

Reissuing to Another User

The SPEX Wonderseat has been designed to accommodate postural asymmetries and adapt to
dierent morphologies. Once the user has finish using the SPEX Wonderseat, it must be refurbished
if it is issued to another user. Below are the strict guidelines for refurbishing the SPEX Wonderseat.
Please also refer to Bingo-OT manual for reissue procedure.

PART PROCEDURE

Upholstery covers

• Upholstery outer covers must be replaced regardless of condition.

Hardware and components

• Ensure the quick release arm supports latches and swing away lateral trunk bracket

are all locking

• Check lateral trunk supports, head support, pelvic supports, arm supports are all

functioning correctly

• Check lateral trunk supports, head support, pelvic supports, arm supports are secure

and tight

• Replace any missing or worn fasteners/adjusting levers and knobs

• Check the overall structure of the Bingo-OT seat and mobility base unit for

any signs of fatigue or damage. Also refer to the guidance given in the Bingo-

OT/Evo Manual.

• Check the Bingo-OT and mobility frame for wear and tear, splinters or breaks

• Check for signs of stress or cracking. If any stress/cracks are found these parts must

be condemned and replaced immediately.

Hip belt & Shoulder harness

• Check the 4-point pelvic strap/2-point pelvic strap/shoulder harness are securely
fitted to the seat and functioning correctly

• Check all the straps for fraying and missing or broken buckles

• Ensure the webbing is clean and freely moves through buckles

Inner contouring • Ensure each contouring pocket has the correct layers of foam

WARNING

1) Medifab takes no responsibility for contamination, cross infection, or damage.

2) All components to be checked for signs of stress or cracking.

48

Product Log

Medifab recommend that you note any changes made to set-up of your
SPEX Wonderseat and Bingo-OT

DAT E Set Up/Checks/Amendments Sinature Print Name

49

The SPEX Wonderseat system should be serviced annually once out of the warranty period. If you
suspect the SPEX Wonderseat has had heavy usage and is still under warranty we recommend you
request a full service. SPEX Wonderseat should only be serviced by a technically competent person/
health care provider who has been trained in the use of the product, a Medifab authorised person or
a local distributor.

Please contact Medifab customer services department or your local dealer for further information.

Medifab recommends that the SPEX Wonderseat be used for a period of

4 years, provided the

product is maintained and serviced as per manufacturer’s instructions.

Back Support

Wonderseat Servicing and Technical Data

Example Product Identification Serial Labels Example

SPEX Wonderseat Size 1 : 2885-0031-032
SPEX Wonderseat Size 2: 2885-0032-032

•Serial numbers can be found on the SPEX Wonderseat Seat cushion and Back support. Please
quote this number in any correspondence.

50

Disposal & Recycling

Your SPEX Wonderseat Seating System is manufactured using a variety of materials, of which most
can be recycled. Once it reaches the end of its life, if you are the legal owner, do not dispose of as
ordinary household waste but take your SPEX Wonderseat system to an approved recycling or
collection point, to dispose of according to local laws and regulations.

Separate collection and recycling of the SPEX Wonderseat system when disposing ensures
protection of the environment and assists with natural resource conservation.

Environment

Moisture

Keep your SPEX Wonderseat supports dry at all times, as contact with water or excess moisture
could cause corrosion, degradation to the functionality of your SPEX Wonderseat or potential
failure. If your Back Support or seat Cushion becomes damp or wet, thoroughly wipe with a dry

cloth as soon as possible.

Temperature

Your SPEX Wonderseat may not function as intended when used at extreme temperatures. Keep
the SPEX Wonderseat and Bingo-OT away from sources of extreme heat or extreme cold to avoid
burns from the metal components.

Dirt

Small particles such as dust, dirt and sand may restrict optimum functionality. Regularly check your
SPEX Wonderseat and Bingo-OT to ensure no build-up occurs around openings and moving parts.

Please record the Medifab Distributor from which you purchased your SPEX Wonderseat.

Company

Address

Phone Website

Contact Email

Serial #

Medifab Service Distributor

51

Bingo Stroller Size Size 1 Size 2

Seating
specs

A Hip width 17-28cm

(6.5-11”) 22-33cm (8 .5-1 3”)

B Seat depth

18-23cm

(7-9” )

1.1 Cushion

23-30cm (9-1 2”)

1.2 Cushion

23-33cm (9-1 3”)

2.1 Cushion

28-38cm (11 -15”)

2.2 Cushion

C Back height 36-44cm (14-1 7”) 40-48cm (16 -19”)

D Lower leg length* 25-40cm (1 0-16") 25-45cm (10-18")

E Trunk lateral width 12-28cm (5 -11”) 15-30cm (6 -12”)

F Trunk lateral trunk height 15-34cm (6-13.5”) 17- 40c m (6. 5-16” )

G Arm supports height 15-22cm (6 -8.5” ) 15-22cm (6 -8.5” )
H Internal arm supports

width

20-32cm (8-1 3”) 28-38cm (11 -15”)

I Head support height 45-65cm (18-2 5.5”) 50 -70cm (2 0-28”)

J Cushion total width 33cm (13”) Size 1 .1 33cm (13”) Size 1 .2 38cm (15”) Siz e 2.1 38cm (15”) Size 2. 2

K Internal cushion width 23cm (9”) Size 1 .1 28cm (11”) Size 1. 2 28cm (11”) Size 2.1 33cm (13”) Size 2. 2

L Centre of thigh contours 15cm (6”) Size 1.1 17cm (6.5 ”) Size 1.2 18cm (7” ) Size 2.1 20cm (8”) Size 2 .2

M Cushion side height 14cm (5.5” ) 14cm (5. 5”)

N Thigh contour height 9cm (3.5”) 9cm (3.5”)

O Abductor contour height 5cm (2 ”) 5cm (2” )

P Back cushion width 33cm (13” ) 38cm (15”)

Q Trunk cushion width 26cm (1 0”) 30cm (12” )

Stroller
specs

1

Frame seat depth capacity 18-30c m (7-1 2”) 20-38cm (8 -15”)

Frame back height capacity 36-46cm (14-18”) 41-55cm (1 6-22”)

Backrest recline angle 90 -16 0°

Height of push bar 75-110cm

(29.5-43”)

Overall frame width 63cm (25” ) 68cm (27” )

Max load of OT seat unit 50kg (110lb) (bo dy weight including ot her load

2

)

Base frame capacity*2

60kg (132 lb)

Max user weight 35kg (7 7lb)

Stroller Package includes matte black
frame 3 kg fabric basket, tray table,
and sun canopy

Note 1, Also refer To Bingo-OT and COBRA base manuals.

Note 2, Refer to Bingo-OT Technical data secon of manual for further

explanaon.

Wonderseat Secifications

52

Manual: SPEX Wonderseat 20180411

Phone [phone]
Fax [phone]

[e-mail]

www.medifab.com

Australian Head Oce
26 Pardoe Street
East Devonport, TAS 7310
Call 1300 543 343

New Zealand Head Oce
32 Detroit Drive
Rolleston 7675
Call 0800 543 343

EC REP

BEO MedConsulting Berlin GmbH

Helmholtzstr. 2

D-10587 Berlin, Germany

Tel: [phone]

US REP

Medicept

200 Homer Ave, Ashland, MA 01721

United States

Tel: [phone]