MediaTek RT5392 User Manual

802.11b/g/n 2T2R WLAN Mini Card

RT5392

User’s Manual

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate this equipment.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11.

This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and

2) The transmitter module may not be co-located with any other transmitter or antenna,

3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band

by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to

Regulatory Domain change.

As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM

integrator is still responsible for testing their end-product for any additional compliance requirements required

with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).

IMPORTANT NOTE: In the event that these conditions can not be met

configurations or co-location with another transmitter), then the FCC authorization is no longer considered

valid and the FCC ID can not

responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC

authorization.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may be installed such that 20

cm may be maintained between the antenna and users. The final end product must be labeled in a visible

area with the following: “Contains FCC ID: VQF-RT5392”.

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install or

remove this RF module in the user’s manual of the end product which integrates this module.

be used on the final product. In these circumstances, the OEM integrator will be

(for example certain laptop

The end user manual shall include all required regulatory information/warning as show in this manual.

Industry Canada Statement

!

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two

conditions:

1) this device may not cause interference and

2) this device must accept any interference, including interference that may cause undesired operation of the

device

This device has been designed to operate with an antenna having a maximum gain of 3.7dBi.

Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna

impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that

the EIRP is not more than required for successful communication.

IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This device is intended only for OEM integrators

under the following conditions:

2/ The antenna must be installed such that 20 cm is maintained between the antenna and users, and

3/ The transmitter module may not be co-located with any other transmitter or antenna,

4/ For all products market in CANADA, OEM has to limit the operation channels in CH1 to CH11 for 2.4GHz

band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user

regarding to Regulatory Domain change.

As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM

integrator is still responsible for testing their end-product for any additional compliance requirements required

with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop

configurations or co-location with another transmitter), then the IC authorization is no longer considered valid

and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be

responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC

authorization.

End Product Labeling

The final end product must be labeled in a visible area with the following: “Contains TX IC : 7542A-RT5392”.

Manual Information That Must be Included

The OEM integrator has to be aware not to provide information to the end user regarding how to install or

remove this RF module in the user’s manual of the end product which integrates this module.

The end user manual shall include all required regulatory information/warning as show in this manual.

אՀᤞ፿ᔞش؀᨜چ೴

ᆖীڤᎁᢞٽ௑հ܅פ෷୴᙮ሽᖲΔᆖ๺ױΔֆ׹Ε೸ᇆࢨࠌش݁լ൓ᖐ۞᧢ޓ᙮෷ΕףՕפ෷ࢨ᧢ޓ଺

๻ૠհ௽ࢤ֗פ౨Ζ

܅פ෷୴᙮ሽᖲհࠌشլ൓ᐙ᥼ଆ౰ڜ٤֗եឫٽຏΙᆖ࿇෼ڶեឫ෼ွழΔᚨمܛೖشΔࠀޏ࿳۟ྤե

ឫழֱ൓ᤉᥛࠌشΖছႈٽຏΔࠉሽ๵ࡳ܂ᄐհྤᒵሽຏΖ܅פ෷୴᙮ሽᖲႊݴ࠹ٽຏࢨՠ

ᄐΕઝᖂ֗᠔᛭شሽᘿ୴ࢤሽᖲ๻ໂհեឫΖ

ءᑓิ࣍࠷൓ᎁᢞ৵ലࠉ๵ࡳ࣍ᑓิء᧯ᑑقᐉٽ௑᧘Δࠀ૞ޣؓ؀Ղᑑقψءข঴փܶ୴᙮ᑓิΚID ᒳᇆω

Europe – EU CE Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been

applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:

- EN 60950-1:2006+A11:2009+A1:2010

Safety of Information Technology Equipment

- EN 62311: 2008

Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic

fields (0 Hz-300 GHz)

(IEC 62311:2007 (Modified))

- EN 300 328 V1.7.1: (2006-10)

- Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission

equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN

covering essential requirements under article 3.2 of the R&TTE Directive

- EN 301 489-1 V1.8.1: (2008-04)

Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Part 1: Common technical requirements

EN 301 489-17 V2.1.1 (2009-05)

Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high

performance RLAN equipment

This device is a 2.4GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA

countries, except in France and Italy where restrictive use applies.

In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the

device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.

This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be

limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the

national spectrum authority in France.

0560

Česky

[Czech]

Dansk

[Danish]

Deutsch

[German]

Eesti

[Estonian]

English

Español

[Spanish]

Ελληνική

[Greek]

[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími

příslušnými ustanoveními směrnice 1999/5/ES.

Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder

de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den

grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG

befindet.

Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment]

vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC.

Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos

esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ

ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

Français

[French]

Italiano

[Italian]

Latviski

[Latvian]

Lietuvių

[Lithuanian]

Nederlands

[Dutch]

Malti

[Maltese]

Magyar

[Hungarian]

Polski [Polish]

Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences

essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti

essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst

Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB

Direktyvos nuostatas.

Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de

essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet essenzjali u ma

provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek és az

1999/5/EC irányelv egyéb elõírásainak.

Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz

pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

Português

[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e

[Portuguese]

Slovensko

[Slovenian]

Slovensky

[Slovak]

Suomi

[Finnish]

Svenska

[Swedish]

outras disposições da Directiva 1999/5/CE.

[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili

direktive 1999/5/ES.

[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné ustanovenia

Smernice 1999/5/ES.

[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen

laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav

och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Hardware Quick Installation Guide

Installing the Wireless Mini PCI Express Module

1. Power down the computer.

2. Plug the Wireless PCI Express Minicard Module board to motherboard minicard slot

3. Connect 2 external antennas used I-PEX connector for WiFi antenna.

4. Power on the computer.

2 external

Un-installing the Wireless Mini PCI Express Module

1. Power down the computer

2. Removed 2 external WiFi antennas from the Wireless Mini PCI Express Module

3. Carefully removed the Wireless PCI Express Minicard Module from the motherboard minicard slot.

4. Power on the computer.

INTRODUCTION

The 11b/g/n 2T2R WLAN Mini Card is a device that allows you connect your computer to a wireless local

area network (LAN). A wireless LAN allows your system to use wireless Radio Frequency (RF) technology to

transmit and receive data without physically attaching to the network. The Wireless protocols that come with

this product ensure data security and isolation from interference generated by other radio frequencies. This

card also allows you to take full advantage of your computer’s mobility with access to real-time information

and online services anytime and anywhere. In addition, this device eliminates the bother of pulling cable

through walls and under furniture. It even allows you to place your system in locations where cabling is

impossible. Modifying and augmenting networks has never been so easy.

Wireless Network Options

The Peer-to-Peer Network

This network installation lets you set a small wireless workgroup easily and quickly. Equipped with wireless

PC Cards or wireless PCI, you can share files and printers between each PC and laptop.

You can also use one computer as an Internet Server to connect to a wired global network and share files

and information with other computers via a wireless LAN.

The Access Point Network The network installation allows you to share files, printers, and Internet access

much more conveniently. With Wireless LAN Cards, you can connect wireless LAN to a wired global

network via an Access Point.