WIRELESS
WEBCAM
User’s Guide
PC Camera for Teleconferencing
& Video Surveillance
MT4027
2
EN
Introduction
Thank you for your purchasing new generation wireless
webcam. Now you can keep your desk in perfect order
and enjoy having video conversations. MT4027 Wireless Webcam has rechargeable battery and high quality microphone built-in. MT4207 uses 2.4 Ghz transmission technology and is always ready to work (webcam
does not need to be synchronized with USB receiver).
Please read this manual before using the device.
Note: before rst use fully charge Wireless Webcam.
Read more in “Charging” section of this manual. One
end of USB cable connect to USB charger port of
MT4027, the other end plug to USB of your computer.
Full charging takes up to 2 hours.
System Requirements
■ CPU Pentium200 or higher
■ operating system WINDOWS XP/VISTA 32bit
■ 20MB available space on HDD
■ CD-ROM drive
■ 128 MB RAM
■ VGA card with DIRECTX support
■ free USB port
Package content
■ Wireless Webcam
■ USB receiver
■ software/driver CD-ROM
■ USB cable
■ user’s manual
Overview
5. Focus adjuster ring/
Built-in Microphone
6. Receiver USB plug
7. Operation indicator
1. Shutter release button
2. Power On/O switch
3. USB charger connector
4. Power On/Charging On
indicator
Wireless Webcam USB Receiver
3
EN
Installation
1. Put the CD into the CD ROM drive, the auto-run
function starts (we use Window XP as example).
When following windows will appear click “Accept”
When following windows will appear click “Install”
2. Now plug USB receiver into free USB port. Windows
“New Hardware Wizard” will recognize and install a
new capturing device.
3. Setup Wireless Webcam on the desk or on the monitor (remember to fully charge Wireless Webcam).
Press “Power On” button at the back of Wireless Webcam.
4.
Run “AMCAP” application to preview captured video.
5. Use “Focus ring” to adjust focus.
Note: close AMCAP before using communication software (like Skype). Video stream can be used only by
one application at one time.
4
EN
Charging
1. Connect USB cable to the charger port of MT4207,
the other end plug to USB port of the computer.
When charging is in progress green LED will be on.
Battery should be charged for about 2 hours to get
full – then green LED will be o .
2. When the battery is low, the red LED will ash. You
may charge the battery when it is working.
3. When Wireless Webcam turned on, the red LED will
keep on.
Using Wireless Webcam
To take snapshot run “AMCAP” application and press
Snapshot button – then save le in directed folder.
Speci cation
■ wireless digital 2.4GHz, high-quality image compression.
■ best operation distance is 1.5-2m
■ power consumption current 200mA
■ built-in rechargeable Li-ion Battery 850mAh 3.7V
■ CMOS sensor VGA.
■ charged from USB port
■ built-in Microphone.
■ Plug&Play in Windows XP/VISTA.
■ supports MSN/QQ/SKYPE
■ frame rate:
mode 320X240: ca. 25 fps within range of 1.5m from
USB receiver
mode 640X480: ca. 5 fps within range of 1.5m from
USB receiver
■ snapshot button
To capture video run “AMCAP” application and select
“Capture” from menu bar.
In “AMCAP” to adjust Brightness, Contrast, Saturation
select “Option” from menu bar.
Note: When using Wireless Webcam, please try to keep
it stable. Otherwise the image quality and frame rate
will decrease. If you need to move the webcam, please
move it in low speed. Best quality is when Wireless Webcam is range of 1.5-2m from USB receiver.
Loading...