Media-Tech MEGA DROIDER IR User Manual

MEGA DROIDER IR

MT1421

Wireless 3 in1 Pointing Device

Introduction

This universal remote control can control up to two de­vices, it can also be used with PC computer or Media­Tech Multimedia Fan Center devices (via USB IR receiv­er). Please read this manual before using the device.

Overview

Front

First device TV

Second device STB

Rear

Right click Lock keypad Capslock

USB IR Receiver

Installing batteries

Using with PC computer/Media-Droid

Plug USB IR Receiver into PC computer or Media-

Droid. Device will be installed automatically, no ad­ditional drivers are required. To use touchpad press it
once do wake it up, then slide fi ngers along to control
mouse movement. Press Lock Keypad button to dis-
able keyboard and mouse, press again to enable.

Remote control setup

Before using remote control you need to set it with
device (TV, DVD, STB or others). You can store two
devices, by default fi rst device is named TV, second is

Power/LED

LEARN

EnterBackspaceLeft click

Mini TouchPad

User Manual

EN

named STB. There are three ways of setup: enter brand
code, automatic search, manual search. Additionally if
not all buttons are working you can use learn function
to setup buttons from original remote.

A. Set up by Brand Code

1. Switch on the device for which you wish to use the
remote control (for instance TV set).

2. Find the code number of your device brand in the
code list (for instance Lifetec 0050) from the relevant
device group (TV ).

3. Press and hold the device button (for instance TV)
for three seconds. Release the device button as soon
as LED lights up, now it is in set up mode.

4. Enter the 4-digit device code (for instance 0050 for
Lifetec TV) within 10 seconds. If an entry is not made
within 10 seconds, the set- up mode is automatically
terminated.

5. The LED turns off if the remote accepts the code. If
the LED fl ashes two times, that means the code may
be wrong, and the remote control remains in set-up
mode, enter the correct code from the list again.

6. Check the function of the buttons on the remote
control. If it does not function correctly, try another
4-digit device code (for instance 0057…) from the
list under the same brand. Repeat steps 3 to 6 until
all the basic functions operate correctly.

Note! Exit the set-up mode by pressing the device
button, or the set-up mode is automatically termi­nated if no button is pressed for 10 seconds.

B. Set up by Automatic Search

If setting up by brand name and codes is not success­ful, or you can not fi nd your brand name in the code
list, you can use the Automatic Search function to fi nd
the correct code for your remote control.

1. Switch on the device that you like to control. If it is a
VCR, insert a cassette.

2. Point the remote control at your device. Press the
device button (for instance TV) for three seconds,
the LED turns on, keep pressing the device button
for about two seconds until the LED starts fl ashing,
that means it is in Automatic Search now and you
can release the device button.

3. The “Volume+” signal is automatically transmitted
from the remote control to the device (code scan).
As soon as the volume of the device (for instance
TV) changes, immediately press the device key to
stop the Automatic Search.

4. If the device you are searching for is a CD player,
Tuner, TAPE, or AUX, a power signal is automatically
transmitted from the remote control to the device.
As soon as the device turns off , press the device key
to stop the Search. You need to turn on the device
by pressing the Power button before you can check
the functions of the other buttons.

EN

5. Check the functions of the other buttons on the
remote control. If none of the buttons function (i.e.
the search cannot be stopped at the correct time)
or the majority of the buttons do not function cor­rectly, restart the search (see steps 2 to 4) to fi nd a
suitable code. If the majority of the buttons func­tion correctly, set- up has been successful. Re-press
the device button (for instance TV) to save the code
and to terminate the set-up mode.

C. Set up by Manual Search

If setting up with brand name and codes is unsuccess­ful, you can also use the “Manual Search” to fi nd the
correct code for operating your device.

1. Switch on the device that you like to control. If it is a
VCR, please insert a cassette.

2. Point the remote control at the device. Press and
hold the device button (for instance TV) for 3 sec­onds. The LED lights up and the remote is in manual
set-up mode, release the device button now.

Press the “Volume+” button approx. every 1.5 seconds.

3.

4. As soon as the volume of the device (for instance
TV) changes or the device turns off , check whether
the other buttons on the remote control function
correctly. If the majority of the buttons does not
function correctly, press the Volume+ approx. every

1.5 seconds to initiate the reactive code ( manual
search is continued, see step 3 to 4). If the majority
of the buttons on the remote control functions cor­rectly, save the code by pressing the device button
(for instance TV) to terminate the manual search.

Note: The Manual Search is automatically terminat­ed if no entry occurs during a 30 seconds period.

D. Setup By Using The Learning Function

The Learning Function is used to extend the pre­programmed codes by transferring codes from your
existing remote control to the keyboard remote. The
standard code list already provides you with the most
important functions, but it is possible to add a few ad­ditional functions. A fully functional original remote
control is required for the keyboard remote to learn
programming. Please use fresh batteries for both the
keyboard remote and the original remote control.

1. Press and hold the ‘Device’ button which you want
to learn (for instance DVD), and press the ‘Learn’ but­ton at the same time. When the LED turns on then
release both keys. Now the remote control is in
Learning Mode for codes.

2. Press and release the target button on your key­board remote that you want to learn (for instance­POWER). The LED will start to fl ash. (If no button is
pressed within 14 seconds, Learning Mode will exit
automatically.)

3.

Press the button (For example, power button) on your
original remote control. When you see the LED on
your new universal remote control fl ash three times
and stop, it means the device has accepted the new
code and it can now start to learn another new code
from the original remote. (If no button is pressed
within 14 seconds, it will exit learning mode auto­matically and you will need to restart from step 1.)

4. Repeat steps 2 to 4 to learn another code from the
original remote control.

5. When you fi nish learning all the buttons that you
want the keyboard remote to know, press the ‘Learn’
button to store all commands you have learned
from the original remote and to exit Learning mode.

6. Press the ‘TV’ button and ‘Number 6’ at the same
time to delete all the codes you have learned for all
devices.

Note:

1. Point the IR transmitter of the original remote
control to face the IR receiver of the keyboard re­mote with approximately 30mm between them.
Hold the two remotes in a straight line to make
the learning process more accurate.

2. When you cannot choose any more buttons on
the new universal remote control for learning, it
means the memory is full.

E. Display the code

1. Press and hold the device button ( TV) and simulta­neously press button 1 to display the thousands of
the 4-digit code. Count how often the LED fl ashes, if
the LED does not fl ash, the number is zero.

2. Press and hold the device button (TV), simultane­ously press button 2 to display the hundreds of the
4-digit code, Count how often the LED fl ashes, if the
LED does not fl ash, the number is zero.

3. Press and hold the device button (TV), simultane­ously press button 3 to display the tens of the 4-digit
code, Count how often the LED fl ashes, if the LED
does not fl ash, the number is zero.

4. Press and hold the device button (T V), simulta­neously press button 4 to display the ones of the
4-digit code, Count how often the LED fl ashes.

For example for Code 0169

1. Press TV and 1 LED fl ashes zero times

2. Press TV and 2 LED fl ashes one time

3. Press TV and 3 LED fl ashes six times

4. Press TV and 4 LED fl ashes nine times

F. Reset / Delete Function

Simply press the device (TV ) button and Button 0 to­gether, when the LED fl ashes three times, all settings
will be deleted, and the remote goes back to factory
default settings.

Specifi cation and appearance of product are subject to
change without prior notice. For technical support please
visit www.media-tech.eu.