Medal Sports 58102 User Manual [es, en]
Please contact us before returning the product to the store.
Toll Free: 877-472-4296
Por favor póngase en contacto con nosotros antes de
devolver el producto a la tienda.
Número telefónico gratis: 877-472-4296
INSTRUCCIONES DE ARMADO
MODEL/MODELO: 58102
28
LIMITED 90 DAYS WARRANTY
This product is covered by a limited warranty that is effective for 90 days from the
date of purchase. If, during the limited warranty period, a part is found to be defective or breaks, we will offer replacement part at no cost to you, the customer. The
only exceptions to the warranty include main frames, table tops, playing surfaces,
batteries or tools.
The above warranty will not apply in cases of damages due to improper usage,
alteration, misuse, abuse, accidental damage or neglect.
This Limited Warranty gives you specific legal rights and you may also have other
rights which vary from one State (province) to another.
“PLEASE SAVE THESE INSTRUCTIONS
AND PURCHASE RECEIPT!”
A PURCHASE RECEIPT (or other proof of purchase date) will be required before
any warranty service is initiated. All requests for warranty service, please feel free
to contact our Consumer Service Department at :
TOLL FREE: 877-472-4296
WEBSITE: www.themdsports.com
*Please be aware of your product’s Limited Warranty for the return/refund policy
from the store, We, at Medal Sports, can not handle the product which is out of
product’s limited warranty since we only provide available parts.
PLEASE CONTACT US BEFORE RETURNING
THE PRODUCT TO THE STORE.
THANK YOU VERY MUCH!
1
WARNING:
!
WARNING:
!
Adult Assembly Required.
2
Power Tools
- Set Low Torque
High Torque
over tightened
CAUTION !
TOOLS REQUIRED:
ASSEMBLY TIPS:
IMPORTANT NOTICE! Please contact us before returning the product to the store.
Please Keep Your Instructions! Your Model number is necessary should you need to contact
us. Please read through this instruction manual book to familiarize yourself with all parts and
assembly steps. Kindly refer to the parts list below and be sure that all parts have been
included.
Although we are dedicated to giving our customers the best product possible, a question may
arise or parts may be missing. If you are missing parts, or, if you have any questions, please
contact our fast and friendly service centre on:
877-472-4296
Phillips Screwdriver - Not Included
Standard (Flat Head Screwdriver) - Not Included
Allen Wrench - Included
Electric Screwdrivers may be helpful during
assembly; however, please set a low torque
and use extreme caution.
1 - Please read the instructions carefully, and follow all assembly, operation or safety instructions
properly in order to avoid damage or injury. For the assembly, at least four adults are required.
2 - Some figures or drawings may not look exactly like your product. Please read and understand
the text before beginning each assembly step.
1 - This product is intended for INDOOR use only.
2 - Please Do Not sit, climb or lean on the game table.
3 - Please Do Not drag the table when moving it in order to avoid the damaged on the legs.
4 - Please only use spray furniture polish to clean the exterior surfaces on the game table.
5 - This is not a child's toy, adult supervision is required for children playing this game.
NOTICE!
58102 PARTS LIST
2 3 4 5 1
Board L Tube
6
11
Ramp U Tube
16
21
2pcs
Right L Tube
1pc
1pc
Allen Key
1pc
Board Tube
2pcs
Left Tube
1pc
Right Tube
1pc
7 8 9 10
Support Tube
2pcs
Mounting Tube
2pcs
Ramp Tube
2pcs
12 13 14 15
Horizontal Tube
2pcs
Ball Return Net
1pc
Electronic Scorer
1pc
17 18 19 20
Rim
2pcs
Rim Support Plate
2pcs
Inflation Pump
1pc
22 23 24 25
Left L Tube
1pc
Ramp L Tube
2pcs
Switch Sensor
2pcs
Pre-installed
Net
2pcs
Backboard
26
M6 x 50mm Bolt
4pcs
1pc
M6 Washer
32pcs
27 28 29
M6 Nut
16pcs
M5 x 20mm Bolt
16pcs
Basketball
4pcs
M6 x 30mm Bolt
6pcs
30
3.5 x 10mm Bolt
4pcs
31 32 33 34 35
Wrench
1pc
M6 x 35mm Bolt
2pcs
36 37 38 39 40
Self-Stick Strap
2pcs
Control Box with Wire
1pc
M5 Nut
16pcs
Pre-installed
Lock Pin
2pcs
4 x 28mm Bolt
2pcs
Pre-installed Pre-installed
Spring Lock
9pcs
M6 x 42mm Bolt
4pcs
TIME
HOME
VISITOR
Electronic Scorer
Face Plate
1pc
M5 Washer
32pcs
Plastic Pole Insert
2pcs
3
ASSEMBLY INSTRUCTIONS
1. Find a clean, level place to begin the assembly of your Basketball Game. We recommend that two adults work
together to assembly this basketball game.
2. Remove all the parts from the box and verify that you have all of the listed parts as shown on the Parts List
below.Carefully cut or tear the four corners of the box so that the bottom of the box can be used as your work
surface.
FIG. 1 & 2
3. Attach the Board Tubes (#2) to the Left Tubes (#3) and Right Tubes( #4) using spring lock as shown in FIG.1.
4. Attach the Support Tubes (#7) to the Mounting Tubes (#8) using spring lock as shown in FIG.2
FIG. 1
2
2
7
Spring Lock
3
4
8
FIG. 2
7
8
FIG. 3
5. Attach the Left L Tube (#5) and Right L Tube (#6) together using spring lock as shown in FIG.3
Spring Lock
FIG. 3
5
6
4
24
22
FIG. 4
24
12
1
2
6. Attach the Left and Right L Tubes (#5 and #6) to Left and Right Tubes (#3 and #4) using Bolts(#26), Washers (#22)
and Nuts(#27), and then attach the Left and Right L Tube (#5 and #6) to the Mounting Tube (#8) using Bolts (#26),
Washers (#22) and Nuts(#27) as shown in FIG.4A &4B.
7. Attach the Support Tube and Mounting Tube (#7 and #8) to the Board Tube(#2) using Bolts(#24), Washers (#22)
and Nuts(#27) as shown in FIG4C, repeat this step for other side. Note: Make sure the spring lock is face down.
27
FIG. 4
2
7
7
3
8
8
5
5
6
6
4
FIG. 4C
27
27
22
24
22
26
FIG. 4A
26
22
FIG. 4B
FIG. 5
8. Attach the Horizontal Tube (#12) to the Board Tube (#2)
using Bolts(#24), Washers(#22) and Nuts(#27) as shown
in FIG5. And then insert the Board L Tubes (#1) to the
Board Tube (#2) as shown in FIG.5.
2
24
7
22
12
FIG. 5
12
1
2
27
5
FIG. 6 & 7
9. Attach the Ramp Tubes(#9) to the Left and Right L Tubess(#5 and #6) using Bolts(#32), Washers(#22) and Nuts
(#27) as shown in FIG 6.
10. Attach the Ramp L Tubes(#10) to the Ramp Tubes(#9) using spring lock, and then attach the Ramp U Tube (#11)
to the Ramp L Tube (#10) using spring lock as shown in FIG 7.
FIG. 6
#39
Spring Lock
11
22
27
32
9
9
22
#40
Plastic Pole Insert
FIG. 7
10
10
11
#39
Spring Lock
6
FIG. 8
11. Attach the Rim Assemblies (#17) and Rim Support Plates (#18) to the Backboard (#21) using the Bolts (#23),
washers (#35) and Nuts (#33). And then attach the Switch Sensor (#15) to the Backboard (#21) using the
Bolts (#23), washers (#35) and Nuts (#33). Make sure that you use washer on both sides of the backboard as
shown in FIG. 8.
33
35
18
FIG. 8
21
17
33
18
35
15
35
23
35
23
17
15
FIG. 9
12. Attach Electronic Scorer Face Plate(#30) to Backboard and connect with the Electronic Scorer(#14) using Bolts
(#29) as shown in FIG. 9.
FIG. 9
29
14
21
TIME
VISITOR
HOME
30
7
Loading...