MeCam DM07 User Manual

1

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is
subjected to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation. SAR test distance is 0mm.
This e
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. The equipment complies with FCC RF exposure limits set

forth for an uncontrolled environment.

T

hese limits are designed to provide reasonable protection
against harmful interference in residential installations. This
equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause interference to radio or television
equipment reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Move the equipment away from the receiver.

- Plug the equipment into an outlet on a circuit different from

that to which the receiver is connected.

- Consult the dealer or an experienced radio/television

technician for additional suggestions.
You are cautioned that any change or modifications to the
equipment not expressly approved by the party responsible for
compliance could void your authority to operate such
equipment.

nt has been tested and found to comply with

quipme

2

Safety Instructions

• Do not drop, puncture or disassemble the device; otherwise

the warranty will be voided.

• Avoid all contact with water. Dry your hands before using

the device.

• Use the device with care. Avoid pressing hard on the device

body.

• For your own safety, avoid using the device when there is a

storm or lightning.

• Use only the accessories supplied by the manufacturer.

• Keep the device out of the reach of infants.

• Do not leave the device on the dashboard where it is subject

to direct sunlight.

• The battery is integrated with the device. Do not dissemble

and modify. The battery should be replaced by an
authorized service center only.

3

Introduction

MeCam is hands-free wearable camera that you can pin or clip
it to your shirt, wear it as a necklace, or mount it to the car
windshield to record high quality videos and pictures.

Package Content

The following items come with your package.

Camera USB Cable Car Adapter (Optional)

Strap Clip Pin Clip

Stand Suction Cup Bracket

(Optional)

4

Product Overview

Function LED

Micro USB port

Function button

Micro SD card slot

5

Power button

HDMI port

Microphone

Power LED

Wi-Fi LED

Buttons and LED Indicators

Button Functions

Status Action

Power on Press and hold the Power button for 2 seconds.

Power off Press and hold the Power button for 3 seconds.

Turn off Wi-Fi Press and hold the Power button for 6 seconds.

Start recording Press and hold the Function button for 3 seconds.

Stop recording

Take photo Press the Function button.

Reset to default

Reboot Press and hold the Power button for 10 seconds.

While recording, press and hold the Function
button for 3 seconds.

Press and hold the Function button for 10
seconds.

LED Indicators

Status Power LED Wi-Fi LED Function LED

Power on Light Green Light Green Off

Start recording Light Green Light Green Blink Green

Wi-Fi off Light Green Off Off

Power off Off Off Off

Battery is charging Off Off Light Red

Charging complete Off Off Off

Low battery Blink Red Off Off

6

Getting Started

Inserting the Memory Card

Insert the memory card with the gold
contacts facing to the front of the device.
Push the memory card until it clicks into
place.

About SD Card

• Please use SD card with the size/memory at least 8GB, Class

10 (up to 64GB).

• Be sure to format SD card using the device before the initial

usage.

• Do not remove the memory card while recording. This may

damage the memory card.

Charging the Battery

1. Connect one end of the USB cable to the micro USB port of

the device.

2. Connect the other

end of the USB cable

to the computer.

7

 Note

• As an alternative, you can also charge the device using an AC

adapter.

Powering the Device On/Off

• To turn on the power, press and hold

the Power button for 2 seconds.

• To turn off the power, press and hold

the Power button for 3 seconds.

8

Connecting to Your Smartphone

List of Supported Smartphone

• iOS device: iOS 6.1 or above

• Android device: Android 4.0 or above

Install MeCam HD APP

1. Make sure your smartphone is connected to the Internet.

2. Launch App Store (iOS)or Google Play/Play Store (Android)

application.

3. On the search bar, enter the keyword “MeCamHD” to search

for APP.

4. Download and install MeCam HD. After the installation is

complete, the MeCam icon ( ) is displayed on the

application screen.

 Note

• When you use a code reader application to scan the

respective QR code below, your smartphone will show a

direct link to download MeCam HD.

(iOS) (Android)

• The application UI varies depending on the device operating

system and design.

9

Connect via Wi-Fi

1. On your smartphone, launch Settings application.

2. In WIRELESS & NETWORKS, tap

Wi-Fi and set it to ON.

The available networks are listed.

3. Tap MeCamHD to connect to the

camera.

4. Enter the password and tap Join

(iOS) or

Connect (Android).

 Note

• The default password is “Enjoylife”.

• You can change the SSID and password in Setup mode.

10

Controlling the Device using APP

Preview Mode

1. Tap Preview tab to switch to Preview/Record mode.

2. Tap to view the live view on your smartphone.

Record Mode

Capture Photos

Select ONE SHOT ( ) to switch to Photo mode.
Tap to capture a photo.

 Note

• You can also press the Function button on the camera to

capture a photo.

11

Capture Continuous Shots

Select PHOTO BURST ( ) to switch
to Continuous Shot mode. Tap and
hold to continuously capture
photos.
Release to stop shooting.

Capture Photos By Time Lapse

Select TIME LAPSE ( ) to switch to

Time Lapse mode.

Tap to continuously capture
photos at the preset interval time.

Tap to stop shooting.

12

Record Videos

Select RECORD VIDEO ( ) to switch
to Video mode.

Tap to start recording.

To stop recording, tap .

Note

• You can also press the Function

button on the camera to
start/stop recording video.

Snap Movie

Select SNAP MOVIE ( ) to switch
to Snap Movie mode.

Tap to start recording a
15-second video clip.

Tap and hold to continuously
record the video. Release it to pause
the recording.

To manually stop recording, tap
Finish.

13

Playback Mode

Tap Playback tab to switch to

Playback mode. Tap Video or Photo
tab to browse the recorded files.

Play Video

1. On Video list, tap the desired

video to play the video.

2. Tap the screen to pause the

playback. Tap the screen again to

resume the video playback.

View Photo

On Photo list, tap the desired photo that you want to view.

Delete Files

On the playback screen, tap to
delete the current file.
A confirmation message appears on
the screen, then tap Delete to
confirm file deletion.

14

Download File into Your Smartphone

On the playback screen, tap > and then select the video
resolution to save the selected video into your smartphone.
The downloaded files are listed in the Mobile list.

(for video only)

Note

• You do not need to specify the photo size before saving it

into the smartphone.

15

Sharing Files

Before sharing the file to Facebook
or YouTube, download the desired
file first into your smartphone.

1. Disconnect the Wi-Fi connection

between the device and your

smartphone. Then connect your

smartphone to the Internet

(either by mobile data connection

or Wi-Fi).

2. Launch MeCam HD application.

3. Tap > Sign in > + >

Facebook ( ) or YouTube ( ).

Follow the on-screen instructions

to login to your social network

account. Tap Finish when the

settings are complete.

4. Tap Playback tab and select file

that you want to share from the

Mobile list.

5. Tap and select Facebook ( )

or YouTube ( ) to share the file.

16

Configuring Settings

Configure the video and photo
recording, wireless connection, and
the device general settings.

1. Tap Settings tab to switch to Setup

mode.

2. Select the desired menu option.

3. Tap to select the desired setting.

Menu Option Description

Video
Resolution

Photo Burst
Frequency

Time Lapse
Frequency

Stabilization Select ON to enable the stabilizer function.

Set the video resolution.
Available options: 1920x1080 30f /
1280x720 60f / 432x240 120f

Specify the number of continuous shots per
second.
Available options: 5p1s / 10p1s / 30p1s

Select the interval options when capturing
photos using Lapse mode.
Available options: 1p2s / 1p30s / 1pm

Available options: ON / OFF

17

Menu Option Description



Wifi Setting Configure the SSID and password settings.

Enter the new SSID and password. Then tap
OK to save the settings.

Date/Time
Setting

Date/Time
Stamp Overlay

Format SD card Select OK to format the memory card

Version
Information

Factory Default Select OK to reset all settings to factory

View the current date and time.

 Note

• The data shown is based on your

smartphone’s date and time settings.

Select ON to include a date and time on a
video stream.

Available options: ON / OFF

installed on the device.

CAUTION:

Formatting is typically irreversible, so be
sure to transfer the recorded files to your PC
first before formatting the SD card.

View the model name and firmware
version.

default settings.

18

Using Accessories

Using the Strap

To use the strap, do the following:

1. Press the quick release buckle to detach

the lanyard clip.

2. Insert the lanyard through the strap

eyelet on the bracket. Make a loop to
secure it.

3. Install the camera into the bracket.

4. Attach the quick release buckle onto

its slot (see Step 1 illustration).
Press the buckle firmly until it snaps
into place.

5. Wear the strap.

19

Using the Clip

To wear the device on your cloth using the clip, do the
following:

1. Install the camera into the bracket.

2. Pinch the prongs to open the

clipper and wear it on your cloth.

Using the Pin Clip

To wear the device on your cloth using the pin clip, do the
following:

1. Install the camera into the

bracket.

20

2. Open the pin by pressing on the

bar. Be careful with the sharp

point.

3. Slide the open pin through the

cloth. Then squeeze the pin and

slide the bar back into position.

Using the Stand

The device can also be used as a
surveillance camera to monitor your home
or office. To attach the stand, do the
following:

1. Install the camera into the bracket. Then

install the stand to the slot on the
bracket.

2. Place the stand on a stable surface.

21

Using the Suction Cup Bracket

The device can be used as a car recorder.
To mount the device in your car
windshield, do the following:

1. Install the camera into the

bracket.

2. With the suction-cup laying flat,

position the suction cup on the
windshield.

3. Hold the base firmly on the

windshield and press down the
clamp to mount the suction cup
bracket to the windshield.

4. Adjust the device position.

• Loose the knob to swivel the

device vertically or horizontally
(up to 360°).

• Then tighten the knob to make

sure the device is securely locked
in place.

22

Specifications

Image Sensor 3.1 Mega pixels CMOS

Video
Resolution

Lens Angle Wide angle lens, FOV 130 (Diagonal)

Aperture Range F/#2.3

File Format MP4 (AVC/H.264)

External
Memory

Interface Micro USB 2.0, Micro HDMI TV Output

Wireless
Connectivity

App Control Android/IOS App for streaming video and

G-Sensor 3 Axis, 0~4G

Battery Build in 720mAh Li Polymer battery

Operating
Temperature

Storage
Temperature

Dimensions 50 x 47 x 27mm

Weight 50 g

1920x1080P(30fps) / 1280×720P(60fps) /
432x240p(120fps)

Micro SD card(SDXC), Min: 8GB, class 10

802.11 b/g/n WiFi

control device

0°C ~ 60°C
(Do NOT expose under sun more than 1 hour)

-20°C ~ 60°C

23

24