Measurement Computing PCIM-DAS1602/16 User Manual

Artisan Technology Group is your source for quality

new and certied-used/pre-owned equipment

• FAST SHIPPING AND

DELIVERY

• TENS OF THOUSANDS OF
IN-STOCK ITEMS

• EQUIPMENT DEMOS

• HUNDREDS OF
MANUFACTURERS

SUPPORTED

• LEASING/MONTHLY
RENTALS

• ITAR CERTIFIED
SECURE ASSET SOLUTIONS

SERVICE CENTER REPAIRS

Experienced engineers and technicians on staff
at our full-service, in-house repair center

Instra

Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com

Contact us: (888) 88-SOURCE | [e-mail] | www.artisantg.com

SM

REMOTE INSPECTION

View

WE BUY USED EQUIPMENT

Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins

www.artisantg.com/WeBuyEquipment

LOOKING FOR MORE INFORMATION?

Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical

specications, manuals, and documentation

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16

Analog & Digital I/O Board

User's Guide

Document Revision 5, June, 2006

© Copyright 2006, Measurement Computing Corporation

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Your new Measurement Computing product comes with a fantastic extra —

Management committed to your satisfaction!

Refer to www.mccdaq.com/execteam.html for the names, titles, and contact information of each key executive at Measurement
Computing.

Thank you for choosing a Measurement Computing product—and congratulations! You own the finest, and you can now enjoy
the protection of the most comprehensive warranties and unmatched phone tech support. It’s the embodiment of our two
missions:

! To offer the highest-quality, computer-based data acquisition, control, and GPIB hardware and software available—at

the best possible price.

! To offer our customers superior post-sale support—FREE. Whether providing unrivaled telephone technical and sales

support on our latest product offerings, or continuing that same first-rate support on older products and operating
systems, we’re committed to you!

Lifetime warranty: Every hardware product manufactured by Measurement Computing Corporation is warranted against
defects in materials or workmanship for the life of the product. Products found defective are repaired or replaced promptly.

Lifetime Harsh Environment Warranty®: We will replace any product manufactured by Measurement Computing
Corporation that is damaged (even due to misuse) for only 50% of the current list price. I/O boards face some tough operating
conditionssome more severe than the boards are designed to withstand. When a board becomes damaged, just return the unit
with an order for its replacement at only 50% of the current list price. We don’t need to profit from your misfortune. By the way,
we honor this warranty for any manufacturer’s board that we have a replacement for.

30 Day Money Back Guarantee: You may return any Measurement Computing Corporation product within 30 days of
purchase for a full refund of the price paid for the product being returned. If you are not satisfied, or chose the wrong product by
mistake, you do not have to keep it. Please call for an RMA number first. No credits or returns accepted without a copy of the
original invoice. Some software products are subject to a repackaging fee.

These warranties are in lieu of all other warranties, expressed or implied, including any implied warranty of merchantability or
fitness for a particular application. The remedies provided herein are the buyer’s sole and exclusive remedies. Neither
Measurement Computing Corporation, nor its employees shall be liable for any direct or indirect, special, incidental or
consequential damage arising from the use of its products, even if Measurement Computing Corporation has been notified in
advance of the possibility of such damages.

HM PCIM-DAS1602_16.doc

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

ii

Trademark and Copyright Information

TracerDAQ, Universal Library, InstaCal, Harsh Environment Warranty, Measurement Computing Corporation, and the
Measurement Computing logo are either trademarks or registered trademarks of Measurement Computing Corporation.

Windows, Microsoft, and Visual Studio are either trademarks or registered trademarks of Microsoft Corporation

LabVIEW is a trademark of National Instruments.

CompactFlash is a registered trademark of SanDisk Corporation.

All other trademarks are the property of their respective owners.

Information furnished by Measurement Computing Corporation is believed to be accurate and reliable. However, no
responsibility is assumed by Measurement Computing Corporation neither for its use; nor for any infringements of patents or
other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent or
copyrights of Measurement Computing Corporation.

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form by any
means, electronic, mechanical, by photocopying, recording, or otherwise without the prior written permission of Measurement
Computing Corporation.

Notice

Measurement Computing Corporation does not authorize any Measurement Computing Corporation product for use
in life support systems and/or devices without prior written consent from Measurement Computing Corporation.
Life support devices/systems are devices or systems which, a) are intended for surgical implantation into the body,
or b) support or sustain life and whose failure to perform can be reasonably expected to result in injury.
Measurement Computing Corporation products are not designed with the components required, and are not subject
to the testing required to ensure a level of reliability suitable for the treatment and diagnosis of people.

iii

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Table of Contents

About this User's Guide ......................................................................................................................vi

What you will learn from this user's guide ........................................................................................................vi

Conventions in this user's guide ........................................................................................................................vi

Where to find more information........................................................................................................................vi

Chapter 1

Introducing the PCIM-DAS1602/16 .................................................................................................. 1-1

Overview: PCIM-DAS1602/16 features......................................................................................................... 1-1

PCIM-DAS1602/16 block diagram ................................................................................................................ 1-1

Software features............................................................................................................................................ 1-2

Chapter 2

Installing the PCIM-DAS1602/16 ...................................................................................................... 2-1

What comes with your PCIM-DAS1602/16 shipment?..................................................................................2-1

Hardware ....................................................................................................................................................................... 2-1

Additional documentation.............................................................................................................................................. 2-1

Optional components ..................................................................................................................................................... 2-1

Unpacking the board....................................................................................................................................... 2-2

Installing the software .................................................................................................................................... 2-2

Default hardware configuration...................................................................................................................... 2-2

Channel Select switch.................................................................................................................................................... 2-3

A/D Range Select switch ............................................................................................................................................... 2-4

Trigger Edge Select jumper ........................................................................................................................................... 2-4

DAC0 and DAC1 Range Select jumper (D/A Converter Reference)............................................................................. 2-5

Clock Select jumper....................................................................................................................................................... 2-5

Installing the PCIM-DAS1602/16 .................................................................................................................. 2-6

Connecting the board for I/O operations ........................................................................................................ 2-6

Connectors, cables – main I/O connector....................................................................................................................... 2-6

Cabling........................................................................................................................................................................... 2-8

Field wiring, signal termination and signal conditioning............................................................................................... 2-9

Chapter 3

Programming and Developing Applications .................................................................................. 3-1

Programming languages ................................................................................................................................. 3-1

Packaged applications programs..................................................................................................................... 3-1

Register-level programming ........................................................................................................................... 3-1

Chapter 4

Calibrating the PCIM-DAS1602/16 ................................................................................................... 4-1

Calibrating the A/D & D/A converters........................................................................................................... 4-1

Required equipment........................................................................................................................................ 4-1

Chapter 5

Specifications.................................................................................................................................... 5-1

Power consumption ........................................................................................................................................ 5-1

Analog input ................................................................................................................................................... 5-1

Accuracy........................................................................................................................................................................ 5-2

Analog input drift........................................................................................................................................................... 5-2

Noise performance......................................................................................................................................................... 5-2

Crosstalk ........................................................................................................................................................................ 5-3

Analog output ................................................................................................................................................. 5-3

Accuracy........................................................................................................................................................................ 5-4

Analog output drift......................................................................................................................................................... 5-4

Digital input / output....................................................................................................................................... 5-4

iv

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide

Digital I/O connector ..................................................................................................................................................... 5-4

Main connector .............................................................................................................................................................. 5-4

Counter ........................................................................................................................................................... 5-5

Environmental ................................................................................................................................................ 5-5

8-channel differential mode pin out ............................................................................................................................... 5-6

16-channel single-ended mode pin out........................................................................................................................... 5-6

v

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Preface

About this User's Guide

What you will learn from this user's guide

This user's guide explains how to install, configure, and use the PCIM-DAS1602/16 device so that you get the
most out of its analog input and digital I/O features.

This user's guide also refers you to related documents available on our web site, and to technical support
resources.

Conventions in this user's guide

For more information on …

Text presented in a box signifies additional information and helpful hints related to the subject matter you are
reading.

Caution! Shaded caution statements present information to help you avoid injuring yourself and others,

damaging your hardware, or losing your data.

<#:#> Angle brackets that enclose numbers separated by a colon signify a range of numbers, such as those assigned

to registers, bit settings, etc.

bold text Bold text is used for the names of objects on the screen, such as buttons, text boxes, and check boxes. For

example:

1. Insert the disk or CD and click the OK button.

italic text Italic text is used for the names of manuals and help topic titles, and to emphasize a word or phrase. For

example:
The InstaCal® installation procedure is explained in the Quick Start Guide.
Never touch the exposed pins or circuit connections on the board.

Where to find more information

The following electronic documents provide information that can help you get the most out of your PCIM­DAS1602/16.

! MCC's Specifications: PCIM-DAS1602/16 (the PDF version of the Electrical Specification Chapter in this

guide) is available on our web site at www.mccdaq.com/pdfs/PCIM-DAS1602-16.pdf.

! MCC's Quick Start Guide is available on our web site at

! MCC's Guide to Signal Connections is available on our web site at

www.mccdaq.com/signals/signals.pdf

! MCC's Universal Library User's Guide is available on our web site at

! MCC's Universal Library Function Reference is available on our web site at

! MCC's Universal Library for LabVIEW™ User’s Guide is available on our web site at

.

.

.

.

PCIM-DAS1602/16 User's Guide (this document) is also available on our web site at

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

.

vi

C

B

Chapter 1

Introducing the PCIM-DAS1602/16

Overview: PCIM-DAS1602/16 features

This manual explains how to configure, install, and use your PCIM-DAS1602/16 board.

The PCIM-DAS1602/16 is a multifunction measurement and control board designed to operate in computers
with PCI bus accessory slots.

The PCIM-DAS1602/16 provides the following:

! Eight differential or 16 single-ended input channels
! 16-bit A/D resolution
! 100 kHz sample rate
! Dual 12-bit analog outputs
! 32 DIO channels
! Three 16-bit counters

PCIM-DAS1602/16 block diagram

PCIM-DAS1602/16 functions are illustrated in the block diagram shown here.

Gain and Offset trimpots

Time Base

10MHz

1MHz

DAC
Data

Control

Analog In
16 ch S.E.
8 ch Diff.

Digital

I/O

CLK

GATE

OUT

Counter

DIO(3:0)

AUX(3:0)

Mux

&

Gain

ADC

Pacer

CTR 2
CTR 1

User

CTR0

16-Bit,100 kHz

Start EOC

Control

1K

FIFO

INT

FPGA

CONTROLLER

Bus

Timing

LOCAL BUS

BADR1

Boot

EEPROM

PCI

CONTROLLER

BADR2
BADR3
BADR4

Interrupt

Gain and Offset trimpots

16-Bit

DAC0

16-Bit

DAC1

D/A 0

D/A 1

PCI BUS (5V/3.3V, Universal 32-BIT, 33MHZ)

P

1-1

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Introducing the PCIM-DAS1602/16

Software features

For information on the features of InstaCal and the other software included with your PCIM-DAS1602/16, refer
to the Quick Start Guide that shipped with your device. The Quick Start Guide is also available in PDF at

.

Check www.mccdaq.com/download.htm
under less commonly used operating systems.

for the latest software version or versions of the software supported

1-2

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Installing the PCIM-DAS1602/16

What comes with your PCIM-DAS1602/16 shipment?

As you unpack your PCIM-DAS1602/16, make sure that the following components are included.

Hardware

! PCIM-DAS1602/16

Chapter 2

Additional documentation

In addition to this hardware user's guide, you should also receive the Quick Start Guide (available in PDF at

the software you received with your PCIM-DAS1602/16 and information regarding installation of that software.
Please read this booklet completely before installing any software or hardware.

). This booklet supplies a brief description of

Optional components

If you ordered any of the following products with your board, they should be included with your shipment.

! Cables

C37FF-x

C37FFS-x

BP40-37

2-1

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Installing the PCIM-DAS1602/16

! Signal termination and conditioning accessories

MCC provides signal termination and signal conditioning products for use with the PCIM-DAS1602/16.
Refer to the "Field wiring, signal termination and signal conditioning
compatible accessory products.

" section for a complete list of

Unpacking the board

As with any electronic device, you should take care while handling to avoid damage from static
electricity. Before removing the PCIM-DAS1602/16 from its packaging, ground yourself using a wrist strap or
by simply touching the computer chassis or other grounded object to eliminate any stored static charge.

If any components are missing or damaged, notify Measurement Computing Corporation immediately by
phone, fax, or e-mail:

! Phone: [phone] and follow the instructions for reaching Tech Support.
! Fax: [phone] to the attention of Tech Support
! Email: [e-mail]

Installing the software

Quick-Start.pdf.

Default hardware configuration

The PCIM-DAS1602/16 board has several switches and jumpers mounted on it that you must set before
installing into your computer if you are not using the default settings. The factory-configured default settings
are listed in Table 2-1. The locations of each switch and jumper are shown in Figure 2-1.

Table 2-1. Switch/jumper factory-configured defaults

Board Label Switch/Jumper description Default Setting

S1 Channel Select switch 8

S2 A/D Range Select switch Bipolar

P2 Clock Select jumper - 1/10 MHz XTAL jumper 1 MHz

P5 and P6 DAC0/DAC1 Bipolar/Unipolar Select jumpers Bipolar

P7 DAC0 and DAC1 Range jumper −5 V to +5 V

P8 Trigger Edge Select jumper Rising Edge

2-2

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Installing the PCIM-DAS1602/16

Figure 2-1. PCIM-DAS1602/16 switch and jumper locations

Before installing the PCIM-DAS1602/16 in the computer, verify that the board is configured with the settings
that you want. Review the following information to change the default configuration of a jumper or switch on
the PCIM-DAS1602/16 board.

Board switches are covered by a metal nameplate

To access the Channel Select switch and the A/D Range Select switch, remove the metal nameplate that covers
them. This plate is secured to the board with two screws.

Channel Select switch

Set the channel mode configuration with switch S1. The analog inputs of the PCIM-DAS1602/16 can be
configured as eight differential channels or 16 single-ended channels. Use the single-ended input mode if you
have more than eight analog inputs to sample. Using the differential input mode allows up to 10 volts of
common mode (ground loop) rejection and will provide better noise immunity.

This switch is factory-configured for eight differential inputs. The Channel Select switch shown in is
set to the "8" position. To configure for 16 channels, set this switch to 16.

8

16

Figure 2-2

8/16 CHANNEL SELECT SWITCH

(8 Channels, Differential Input Mode Shown)

Figure 2-2. 8/16 Channel Select switch

2-3

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Installing the PCIM-DAS1602/16

A/D Range Select switch

The A/D converter range is set by switch S2. This switch controls all A/D channels.

Although you cannot run some channels bipolar and some unipolar, you can measure a unipolar input in the
bipolar mode (for example, you can monitor a 0 to 5V input with a channel set to the ±5 V range). This switch
is factory-configured for bipolar. The A/D Range Select switch shown in is configured for unipolar. Figure 2-3

Figure 2-3. A/D Range Select switch

Trigger Edge Select jumper

The original Keithley MetraByte DAS-1600 was designed such that A/D conversion initiates on the falling edge
of the convert signal. Neither the original DAS-16, nor any of the other DAS-16 derivative converts on the
falling edge of the signal. In fact, we are not aware of any A/D board that uses the falling edge to initiate the
A/D conversion.

When using the falling edge to start the conversion, the A/D may be falsely triggered by 8254 pacer clock
initialization glitching. False triggering is easy to avoid, but may occur in the DAS-1600. Since initiating
conversions on the falling edge is undesirable, but initiating on the rising edge may lead to timing differences if
the PCIM-DAS1602/16 board is used as a replacement for an older DAS16 series board, the PCIM­DAS1602/16 is equipped with a jumper that you can use to select the edge that initiates the A/D conversion.

The Trigger Edge Select mode is configured by jumper

P8. This jumper is factory-configured for rising edge.

shows the edge selection options. Figure 2-4

Falling Edge A/D Trigger
DAS-1600 Method

P8

Rising Edge A/D Trigger
DAS-16 Method

Default
Setting

P8

Figure 2-4. Trigger Edge Select jumper

For compatibility with all third party packages, with all DAS-16 software, and with PCIM-DAS1602/16
software, leave this jumper in the default rising edge position.

2-4

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Installing the PCIM-DAS1602/16

DAC0 and DAC1 Range Select jumper (D/A Converter Reference)

The PCIM-DAS1602/16 has an on-board precision voltage reference at jumper P7 that you can use to select the
output ranges of the digital to analog converters. Both of the board's D/A outputs are factory-configured with a
range of −5 to +5 volts ( .) Figure 2-5

Analog output is provided by two 12-bit multiplying D/A converters (DAC1 and DAC). This type of converter
accepts an input reference voltage, and provides an output voltage which is both inverse to the reference voltage
and proportional to the digital value in the output register. The proportion is controlled by the D/A output code
(0 to 4095). Each bit represents 1/4096 of full scale. For example, in unipolar mode, the supplied reference of

−5 V provides a +5V output (actually 4.9988 V) when the value in the output register is 4095 (full scale at 12
bits of resolution). It provides a value of 2.5 V when the value in the output register is 2048.

A precision −5 V and −10 V reference provides onboard D/A ranges of 0 to 5 V, 0 to 10 V, ±5 V, ±10 V. Other
ranges between 0V and 10V are available when you provide a precision voltage reference at pin 10 (D/A0) or
pin 26 (D/A1) of the board's main connector.

B

P6 P5

U

DAC1

Bipolar/Unipolar Select jumpers

1 S1
0H05UU5

Code Function

U

User supplied D/A reference

5

5 Volt Range
10 Volt Range

10

Sample & Hold Trigger

SH

D/A0 and D/A1 Range jumper block

Figure 2-5. D/A0 and D/A1 Range jumper

Simultaneous sample and hold (SSH) trigger

B
U

DAC0

(default jumpers shown)

When the DAC1 reference is supplied on-board, pin 26 of the 37-pin connector is unused ( ). You can

Figure 2-7
enable this pin as a SSH (simultaneous sample & hold) trigger for use with the CIO-SSH16 board. To configure
this, place the jumper between the two pins labeled SH, as shown in .

Figure 2-5

Clock Select jumper

Jumper P2 configures the frequency of the square wave used as a clock by the A/D pacer circuitry. This pacer
circuitry controls the sample timing of the A/D.

You can configure the frequency for 10 MHz or 1 MHz. The Clock Select jumper is factory-configured for 1
MHz, as shown in . Figure 2-6

2-5

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Installing the PCIM-DAS1602/16

M

CLK SEL

10M

1

Figure 2-6. Clock Select jumper

Configure this jumper for 10 MHz, unless you have reason to do otherwise.

Internal pacer output is also available at pin 20

The internal pacer output driving the A/D converter is also available at pin 20 (CTR 3 Output) on the board's
main I/O connector (see Figure 2-7).

Installing the PCIM-DAS1602/16

After you configure the board's switches and jumpers, install the PCIM-DAS1602/16 into your computer. To
install your board, follow the steps below:

Install the MCC DAQ software before you install your board

The driver needed to run your board is installed with the MCC DAQ software. Therefore, you need to install the
MCC DAQ software before you install your board. Refer to the Quick Start Guide for instructions on installing
the software.

1.

Turn your computer off, open it up, and insert your board into any available PCI slot.

2.

Close your computer and turn it on.

3.

If you are using an operating system with support for plug-and-play (such as Windows 2000 or Windows
XP), a dialog box pops up as the system loads indicating that new hardware has been detected. If the
information file for this board is not already loaded onto your PC, you will be prompted for the disk
containing this file. The MCC DAQ software contains this file. If required, insert the Measurement
Computing Data Acquisition Software CD and click

OK.

4.

To test your installation and configure your board, run the InstaCal utility installed in the previous section.
Refer to the Quick Start Guide that came with your board for information on how to initially set up and
load InstaCal.

Board configuration with InstaCal

If you change the board configuration with InstaCal, you may have to also physically change the setting of a
corresponding switch or jumper on the board. Refer to Default hardware configuration on page 2-2 for specific
jumper and switch information.

Allow your computer to warm up for at least 15 minutes before acquiring data. The high speed components
used on the board generate heat, and it takes this amount of time for a board to reach steady state if it has been
powered off for a significant amount of time.

Connecting the board for I/O operations

Connectors, cables – main I/O connector

The PCIM-DAS1602/16 board has a 37-pin connector for analog connections and a 40-pin connector for digital
I/O connections. lists the board connectors, applicable cables, and compatible accessory products for
the PCIM-DAS1602/16.

Table 2-2

2-6

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Installing the PCIM-DAS1602/16

Table 2-2. Board connectors, cables, accessory equipment

Analog connector type 37-pin male "D" connector

Digital connector type 40-pin header connector

Compatible cables C37FF-x (Figure 2-10)

C37FFS-x (Figure 2-11)
BP40-37 (Figure 2-12)

Compatible accessory products
(with the C37FF-x cable or C37FFs-x cable)

CIO-MINI37
SCB-37
ISO-RACK16
ISO-DA02

Compatible accessory products
(with the C37FF-x cable or C37FFs-x cable

connected to the BP40-37 cable)

CIO-ERB08
CIO-ERB24
SSR-RACK08
SSR-RACK24

Analog connector

The PCIM-DAS1602/16 board's analog connector is a 37-pin "D" connector that is accessible from the rear of
the PC on the expansion back plate. This connector accepts female 37-pin D-type connectors, such as the
C37FF-x 37-pin cable (Figure 2-10) or the C37FFS-x 37-pin shielded cable (Figure 2-11).

An additional signal, SS&H OUT (Simultaneous Sample and Hold Output), is available at pin 26 of the analog
connector. This pin is required when the CIO-SSH16 board is used with a PCIM-DAS1602/16. Refer to

Simultaneous sample and hold (SSH) trigger

DIG IN 0/EXT TRIG, PACER, GATE

DIG IN 2/CTR1 GATE

D/A REF IN/SS&H OUT

on page 2-5 for information on how to configure this pin.

CTR 1 CLOCK IN

DIG OUT 2
DIG OUT 0

D/A 1 OUT

LLGND
LLGND

CH7 HIGH

CH6 HIGH
CH5 HIGH
CH4 HIGH
CH3 HIGH
CH2 HIGH
CH1 HIGH
CH0 HIGH

PCI Slot

20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37

+5V PC BUS
CTR 1 OUT
DIG OUT 3
DIG OUT 1
DIG IN 3
DIG IN 1
DIG GND

-5V REF OUT
D/A 0 OUT
D/A 0 REF IN
CH7 LOW / CH 15 HIGH
CH6 LOW / CH 14 HIGH
CH5 LOW / CH 13 HIGH
CH4 LOW / CH 12 HIGH
CH3 LOW / CH11 HIGH
CH2 LOW / CH 10 HIGH
CH1 LOW / CH 9 HIGH
CH0 LOW / CH 8 HIGH
LLGND

Figure 2-7. Main I/O connector pin out

Digital connector

The board's digital I/O connector is a 40-pin connector that is mounted at the rear of the PCIM-DAS1602/16.
This connector accepts a 40-pin header connector (Figure 2-12).

The optional BP40-37 cable assembly brings the signals to a back plate with a 37-pin male connector mounted
in it. When connected through the BP40-37 cable, the PCIM-DAS1602/16 board's digital connector is identical
to the CIO-DIO24 connector.

2-7

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Installing the PCIM-DAS1602/16

Analog and digital connections and configuration

General information on analog and digital signal connections and configuration is contained in the Guide to
Signal Connections (available on our web site at http://www.mccdaq.com/signals/signals.pdf).

OR T

PB7 5

OR T

PB6 7

OR T

PB5 9

OR T

PB4 11

OR T

P B3 13

OR T

P B2 15

OR T

P B1 17

OR T

P B0 19

Figure 2-8. Digital I/O connector pin out

Cabling

NC 1

NC 3

GND 21

NC 23

GND 25

NC 27

GND 29

NC 31

GND 33

+5V 35

GND 37

NC 39

1

2 +5V
4 GND
6 P C7

OR T

8 P C6

OR T

10 P C5

OR T

12 P C4

OR T

14 P C3

OR T

16 P C2

OR T

18 P C1

OR T

20 P C0

OR T

22 P A7

OR T

24 P A6

OR T

26 P A5

OR T

28 PORT A4
30 PORT A3
32 PORT A2
34 PORT A1
36 PORT A0
38 NC
40 NC

Figure 2-9. BP40-37 connector pin out

The red stripe

identifies pin # 1

20

1

20

37

19

Figure 2-10. C37FF-x cable

1

20

19

37

Figure 2-11. C37FFS-x cable

19

19

37

1

20

37

2-8

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Installing the PCIM-DAS1602/16

40

19

37

Key

39

1

20

Figure 2-12. BP40-37 cable

2

1

The red stripe
identifies pin # 1

Field wiring, signal termination and signal conditioning

You can use the following MCC screw terminal boards to terminate field signals and route them into the PCIM­DAS1602/16 board using the C37FF-x or C37FFS-x cable:

! CIO-MINI37 – 37-pin screw terminal board. Details on this product are available at

www.mccdaq.com/cbicatalog/cbiproduct.asp?dept_id=102&pf_id=255

! SCB-37 – 37 conductor, shielded signal connection/screw terminal box that provides two independent 50-

pin connections. Details on this product are available at

www.mccdaq.com/cbicatalog/cbiproduct.asp?dept_id=196&pf_id=1166.

MCC provides the following analog signal conditioning products for use with the PCIM-DAS1602/16 board:

! ISO-RACK16 – Isolated 16-channel, 5B module rack for analog signal conditioning and expansion. Details

on this product are available on our web site at

www.mccdaq.com/cbicatalog/cbiproduct.asp?dept_id=127&pf_id=450

! ISO-DA02 – Isolated 2-channel, 5B module rack for analog signal conditioning and expansion. Details on

this product are available on our web site at

www.mccdaq.com/cbicatalog/cbiproduct.asp?dept_id=128&pf_id=703.

.

.

MCC provides the following digital signal conditioning products for use with the PCIM-DAS1602/16 board:

! CIO-ERB08 – 8-channel, Form C relay accessory board for digital signal conditioning. Details on this

product are available on our web site at

www.mccdaq.com/cbicatalog/cbiproduct.asp?dept_id=123&pf_id=240.

! CIO-ERB24 – 24-channel, Form C relay accessory board for digital signal conditioning. Details on this

product are available on our web site at

www.mccdaq.com/cbicatalog/cbiproduct.asp?dept_id=123&pf_id=241.

! SSR-RACK08 – 8-channel, solid-state relay mounting rack for digital signal conditioning. Details on this

product are available on our web site at

www.mccdaq.com/cbicatalog/cbiproduct.asp?dept_id=122&pf_id=620.

! SSR-RACK24 – 24-channel, solid-state relay mounting rack for digital signal conditioning. Details on this

product are available on our web site at

www.mccdaq.com/cbicatalog/cbiproduct.asp?dept_id=122&pf_id=1193.

2-9

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Chapter 3

Programming and Developing Applications

After following the installation instructions in Chapter 2, your board should now be installed and ready for use.
Although the board is part of the larger DAS family, in general there may be no correspondence among
registers for different boards. Software written at the register level for other DAS models will not function
correctly with your board.

Programming languages

Packaged applications programs

Many packaged application programs, such as SoftWIRE and HP-VEE™, now have drivers for your board. If
the package you own does not have drivers for the board, please fax or e-mail the package name and the
revision number from the install disks. We will research the package for you and advise how to obtain drivers.



or any other language, please refer to the Universal Library User's Guide (available on our web

).

Some application drivers are included with the Universal Library package, but not with the application package.
If you have purchased an application package directly from the software vendor, you may need to purchase our
Universal Library and drivers. Please contact us by phone, fax or e-mail:

! Phone: [phone] and follow the instructions for reaching Tech Support.
! Fax: [phone] to the attention of Tech Support
! Email: [e-mail]

Register-level programming

You should use the Universal Library or one of the packaged application programs mentioned above to control
your board. Only experienced programmers should try register-level programming. If you need to program at
the register level in your application, refer to the Register Map for the PCIM-DAS1602/16 (available at

www.mccdaq.com/registermaps/RegMapPCIM-DAS1602-16.pdf).

3-1

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Chapter 4

Calibrating the PCIM-DAS1602/16

The PCIM-DAS1602/16 is shipped fully calibrated from the factory. For normal environments, you should
calibrate your PCIM-DAS1602/16 board using InstaCal's calibration procedures every six months–to-a year. If
frequent variations in temperature or humidity are common, recalibrate at least every three months. It requires
less than 20 minutes to calibrate the board using InstaCal.

The InstaCal calibration procedure is explained in the DAQ Software Quick Start that was shipped with your
board.

Calibrating the A/D & D/A converters

InstaCal provides step-by-step on-screen instructions to guide you in calibrating your board. You calibrate the
board's A/D converters by applying a known voltage to an analog input channel and adjusting trim pots for
offset and gain. There are three trim pots that require adjustment to calibrate the analog input section of the
board. There are also three pots associated with each of the analog output channels.

Calibrate the PCIM-DAS1602/16 for the range you intend to use it in. When the range is changed, slight
variation in Zero and Full Scale may result. These variations can be measured and removed in software if
necessary.

Required equipment

To calibrate the PCIM-DAS1602/16, you need a precision voltage source, or a non precision source and a 5½
digit digital voltmeter and a few pieces of wire. Use a jeweler’s screwdriver to adjust the trim pots. An extender
card is not required to calibrate the board.

4-1

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Specifications

Typical for 25 °C unless otherwise specified.

Specifications in italic text are guaranteed by design.

Power consumption

+5V quiescent 820mA typical, 1.4A max

Analog input

A/D converter type LTC1605CSW

Resolution 16 bits

Number of channels 16 single-ended / 8 differential, switch selectable

Input ranges

! Gain is software selectable
! Unipolar/Bipolar polarity is switch selectable

A/D Pacing (software programmable)

A/D Trigger (only available when internal
pacing selected, software enable/disable)

A/D Gate
(only available when internal pacing selected,

software enable/disable)

Simultaneous Sample and Hold Trigger

Burst Mode Software selectable option, burst interval = 10uS

Data Transfer

Interrupt INTA# - mapped to IRQn via PCI BIOS at boot-time

Interrupt enable Programmable through PLX9052

Interrupt polarity

Interrupt Sources (software programmable)

A/D conversion time 10µs max

Throughput 100KHz

Common Mode Range ±10V min

CMRR @ 60Hz -100dB typ, -80dB min

Input leakage current ±3nA max

Input impedance 10 MOhms min

Absolute maximum input voltage +55/-40V fault protected via input mux

±10V, ±5V, ±2.5V, ±1.25V
0 to 10V, 0 to 5V, 0 to 2.5V, 0 to 1.25V

Internal counter - 82C54.
Positive or negative edge, jumper selectable.

External source (pin25), positive or negative edge, software
selectable.

Software polled

External edge trigger (pin 25),
Positive or negative edge, software selectable.

External gate (pin 25),
High or Low level, software selectable.

TTL output (pin 26), jumper enabled.
Logic 0 = Hold, Logic 1 = Sample
Compatible with CIO-SSH16

From 1024 sample FIFO via interrupt w/ REPINSW

Interrupt

Software polled

Active high level or active low level, programmable through
PLX9052

End of Conversion

FIFO not Empty

End of Burst

End of Acquisition

FIFO Half Full

Chapter 5

5-1

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Specifications

Accuracy

Typical Accuracy ±2.3 LSB

Absolute Accuracy ±5.0 LSB

Accuracy Components

Gain Error Trimmable by potentiometer to 0

Offset Error Trimmable by potentiometer to 0

PGA Linearity Error ±1.3 LSB typ , ±10.0 LSB max

Integral Linearity Error ±0.5 LSB typ , ±3.0 LSB max

Differential Linearity Error ±0.5 LSB typ, ±2.0 LSB max

Each PCIM-DAS1602/16 is tested at the factory to assure the board’s overall error does not exceed ±5 LSB.

Total board error is a combination of gain, offset, differential linearity and integral linearity error. The
theoretical absolute accuracy of the board may be calculated by summing these component errors. Worst case
error is realized only in the unlikely event that each of the component errors are at their maximum level, and
causing error in the same direction.

Analog input drift

Range Analog Input Full-

Scale Gain drift

±10.00V 2.2 LSB/°C max 1.8 LSB/°C max 4.0 LSB/°C max

±5.000V 2.2 LSB/°C max 1.9 LSB/°C max 4.1 LSB/°C max

±2.500V 2.2 LSB/°C max 2.0 LSB/°C max 4.2 LSB/°C max

±1.250V 2.2 LSB/°C max 2.3 LSB/°C max 4.5 LSB/°C max

0 - 10.00V 4.1 LSB/°C max 1.9 LSB/°C max 6.0 LSB/°C max

0 - 5.000V 4.1 LSB/°C max 2.1 LSB/°C max 6.2 LSB/°C max

0 - 2.500V 4.1 LSB/°C max 2.4 LSB/°C max 6.5 LSB/°C max

0 - 1.250V 4.1 LSB/°C max 3.0 LSB/°C max 7.1 LSB/°C max

Analog Input Zero drift Overall Analog Input drift

Absolute error change per °C Temperature change is a combination of the gain and offset drift of many
components. The theoretical worst case error of the board may be calculated by summing these component
errors. Worst case error is realized only in the unlikely event that each of the component errors are at their
maximum level, and causing error in the same direction.

Noise performance

The following table summarizes the worst case noise performance for the PCIM-DAS1602/16. Noise
distribution is determined by gathering 50000 samples with inputs tied to ground at the PCIM-DAS1602/16
main connector. Data is for both Single-Ended and Differential modes of operation.

Range ±2 counts ±1 count Max Counts LSBrms*

±10.00V 97% 80% 11 1.7

±5.000V 97% 80% 11 1.7

±2.500V 96% 79% 11 1.7

±1.250V 96% 79% 11 1.7

0 - 10.00V 88% 65% 15 2.3

0 - 5.000V 88% 65% 15 2.3

0 - 2.500V 83% 61% 15 2.3

0 - 1.250V 83% 61% 16 2.4

* Input noise is assumed to be Gaussian. An RMS noise value from a Gaussian distribution is calculated by
dividing the peak-to-peak bin spread by 6.6

5-2

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Specifications

Crosstalk

Crosstalk is defined here as the influence of one channel upon another when scanning two channels at the
specified per channel rate for a total of 50000 samples. A full scale 100Hz triangle wave is input on channel 1.
channel 0 is tied to analog ground at the 100 pin user connector. The table below summarizes the influence of
channel 1 on channel 0 and does not include the effects of noise.

Range 1 kHz Crosstalk

(LSB pk-pk)

±10.000 V 4 13 24

±5.000 V 2 7 18

±2.500 V 2 5 16

±1.250 V 3 4 14

0 V to +10.000 V 4 8 23

0 V to +5.000 V 2 5 16

0 V to +2.500 V 2 4 16

0 V to +1.250 V 3 3 16

10 kHz Crosstalk
(LSB pk-pk)

50 kHz Crosstalk
(LSB pk-pk)

Analog output

D/A converter type MX7548

Resolution 12 bits

Number of channels 2

Channel type Single-ended voltage output

Output range
(jumper selectable per output)

(jumper selectable)

External reference voltage range ±10 V max

External reference input impedance 10 KOhm min

Data transfer Programmed I/O

Throughput

Monotonicity Guaranteed monotonic over temperature

Slew rate 2.0 V/µs min

Settling time 30 µS max to ±½ LSB for a 20 V step

Current drive ±5 mA min

Output short-circuit duration Indefinite @ 25 mA

Output coupling DC

Output impedance 0.1 ohms max

Output stability Any passive load

Coding Offset binary

Output voltage on power up and reset 0 V ± 10 mV

±10 V, ±5 V, 0 to 10 V, or 0 to 5 V using on-board references, or user defined
using external reference

On-board, -10 V and –5 V Reference voltage

External
Independent (D/A0 pin 10 and D/A1 pin 26)

System dependent. Using the Universal Library programmed output function
(cbAOut()) in a loop, in Visual Basic, a typical update rate of 400 Khz can be
expected on a 300 MHz Pentium II based PC.

Bipolar mode:
0 code = Vref

4095 code = -Vref – 1LSB, Vref < 0V

-Vref + 1LSB, Vref >0V

Unipolar mode:
0 code = 0V,

4095 code = -Vref – 1LSB, Vref < 0V

-Vref + 1LSB, Vref >0V

5-3

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Specifications

Accuracy

Typical accuracy ±1 LSB

Absolute accuracy ±2 LSB

Accuracy Components

Gain error Trimmable by potentiometer to 0

Offset error Trimmable by potentiometer to 0

Integral linearity error ±0.5 LSB typ, ±1 LSB max

Differential linearity error ±0.5 LSB typ, ±1 LSB max

Total board error is a combination of gain, offset, differential linearity and integral linearity error. The
theoretical absolute accuracy of the board may be calculated by summing these component errors. Worst case
error is realized only in the unlikely event that each of the component errors are at their maximum level, and
causing error in the same direction.

Analog output drift

Analog output full-scale gain drift ±0.22 LSB/°C max

Analog output zero drift ±0.22 LSB/°C max

Overall analog output drift ±0.44 LSB/°C max

Absolute error change per °C temperature change is a combination of the gain and offset drift of many
components. The theoretical worst case error of the board may be calculated by summing these component
errors. Worst case error is realized only in the unlikely event that each of the component errors are at their
maximum level, and causing error in the same direction.

Digital input / output

Digital I/O connector

Digital type 82C55

Number of I/O 24

Configuration per 82C55

Input high 2.0 volts min, 5.5 volts absolute max

Input low 0.8 volts max, -0.5 volts absolute min

Output high 3.0 volts min @ -2.5 mA

Output low 0.4 volts max @ 2.5 mA

Power-up / reset state Input mode (high impedance)

Pull-up/pull-down resistors User installed. Dual footprint allows pull-up or pull-down configuration

Main connector

Digital output type 74LS244, power up / reset to LOW logic level

Digital input type 74LS373, pulled to logic high via 10 K resistors

Number of I/O 8

Configuration 4 fixed input, 4 fixed output

Output high 2.7 volts @ -0.4 mA min

Output low 0.5 volts @ 8 mA max

Input high 2.0 volts min, 7 volts absolute max

Input low 0.8 volts max, -0.5 volts absolute min

2 banks of 8 and 2 banks of 4 or

3 banks of 8 or

2 banks of 8 with handshake

5-4

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Specifications

Counter

Counter type 82C54

Configuration 3 down counters, 16 bits each

Counter 1 source
(software selectable)

Counter 1 gate External gate from main connector (pin 24*)

Counter 1 output Available at main connector (pin 2)

Counter 2 source
(jumper selectable)

Counter 2 gate
(software enable/disable)

Counter 2 output Internal only, chained to counter 3 source

Counter 3 source Counter 2 output

Counter 3 gate
(software enable/disable)

Counter 3 output Available at main connector (pin 20)

Clock input frequency 10 MHz max

High pulse width (clock input) 30 ns min

Low pulse width (clock input) 50 ns min

Gate width high 50 ns min

Gate width low 50 ns min

Input high 2.0 volts min, 5.5 volts absolute max

Input low 0.8 volts max, -0.5 volts absolute min

Output high 3.0 volts min @ -2.5 mA

Output low 0.4 volts max @ 2.5 mA

Crystal oscillator frequency 10 MHz

Frequency accuracy 50 ppm

! External source from main connector (pin 21*)
! 100 kHz internal source

! Internal 1 MHz
! Internal 10 MHz

External source from main connector (pin 25*)

External source from main connector (pin 25*)

Programmable as ADC Pacer clock.

* Pins 21, 24, and 25 are pulled to logic high via 10K resistors.

Environmental

Operating temperature range 0 to 70°C
Storage temperature range -40 to 100°C
Humidity 0 to 95% non-condensing

Mechanical

Card dimensions PCI custom type card: 107 mm (H) x 18.5 mm (W) x 216 mm (L)

5-5

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Specifications

Main connector and pin out

Connector type 37 pin male "D" connector

Connector Compatibility Identical to CIO-DAS1602/16 Connector

8-channel differential mode pin out

Pin Signal Name Pin Signal Name

1 +5V PC BUS POWER 20 CTR 3 OUT
2 CTR 1 OUT 21 CTR 1 CLOCK IN
3 DIG OUT 3 22 DIG OUT 2
4 DIG OUT 1 23 DIG OUT 0
5 DIG IN 3 24 DIG IN 2 / CTR1 GATE
6 DIG IN 1 25 DIG IN 0 / EXT TRIG / EXT PACER / EXT GATE
7 DIG GND 26 D/A1 REF IN / SS&H OUT
8 -5V REF OUT 27 D/A 1 OUT
9 D/A 0 OUT 28 AGND
10 D/A0 REF IN 29 AGND
11 CH7 LO 30 CH7 HIGH
12 CH6 LO 31 CH6 HIGH
13 CH5 LO 32 CH5 HIGH
14 CH4 LO 33 CH4 HIGH
15 CH3 LO 34 CH3 HIGH
16 CH2 LO 35 CH2 HIGH
17 CH1 LO 36 CH1 HIGH
18 CH0 LO 37 CH0 HIGH
19 AGND

16-channel single-ended mode pin out

Pin Signal Name Pin Signal Name

1 +5V PC BUS POWER 20 CTR 3 OUT
2 CTR 1 OUT 21 CTR 1 CLOCK IN
3 DIG OUT 3 22 DIG OUT 2
4 DIG OUT 1 23 DIG OUT 0
5 DIG IN 3 24 DIG IN 2 / CTR1 GATE
6 DIG IN 1 25 DIG IN 0 / EXT TRIG / EXT PACER / EXT GATE
7 DIG GND 26 D/A1 REF IN / SS&H OUT
8 -5V REF OUT 27 D/A 1 OUT
9 D/A 0 OUT 28 AGND
10 D/A0 REF IN 29 AGND
11 CH15 HIGH 30 CH7 HIGH
12 CH14 HIGH 31 CH6 HIGH
13 CH13 HIGH 32 CH5 HIGH
14 CH12 HIGH 33 CH4 HIGH
15 CH11 HIGH 34 CH3 HIGH
16 CH10 HIGH 35 CH2 HIGH
17 CH9 HIGH 36 CH1 HIGH
18 CH8 HIGH 37 CHO HIGH
19 AGND

5-6

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PCIM-DAS1602/16 User's Guide Specifications

Digital input / output connector and pin out

Connector type 40 pin header

Connector Compatibility Identical to CIO-DAS1602/16 Connector

Pin Signal Name Pin Signal Name

1 NC 2 +5V PC BUS POWER
3 NC 4 DIG GND
5 PORT B 7 6 PORT C 7
7 PORT B 6 8 PORT C 6
9 PORT B 5 10 PORT C 5
11 PORT B 4 12 PORT C 4
13 PORT B 3 14 PORT C 3
15 PORT B 2 16 PORT C 2
17 PORT B 1 18 PORT C 1
19 PORT B 0 20 PORT C 0
21 DIG GND 22 PORT A 7
23 NC 24 PORT A 6
25 DIG GND 26 PORT A 5
27 NC 28 PORT A 4
29 DIG GND 30 PORT A 3
31 NC 32 PORT A 2
33 DIG GND 34 PORT A 1
35 +5V PC BUS POWER 36 PORT A 0
37 DIG GND 38 NC
39 NC 40 NC

5-7

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Declaration of Conformity

Manufacturer: Measurement Computing Corporation
Address: 10 Commerce Way
Suite 1008
Norton, MA 02766
USA

Category: Electrical equipment for measurement, control and laboratory use.

Measurement Computing Corporation declares under sole responsibility that the product

PCIM-DAS1602/16

to which this declaration relates is in conformity with the relevant provisions of the following standards or other
documents:

EU EMC Directive 89/336/EEC: Electromagnetic Compatibility, EN55022 (1995), EN55024 (1998)

Emissions: Group 1, Class B

! EN55022 (1995): Radiated and Conducted emissions.

Immunity: EN55024

! EN61000-4-2 (1995): Electrostatic Discharge immunity, Criteria A.
! EN61000-4-3 (1997): Radiated Electromagnetic Field immunity Criteria A.
! EN61000-4-4 (1995): Electric Fast Transient Burst immunity Criteria A.
! EN61000-4-5 (1995): Surge immunity Criteria A.
! EN61000-4-6 (1996): Radio Frequency Common Mode immunity Criteria A.
! EN61000-4-8 (1994): Power Frequency Magnetic Field immunity Criteria A.
! EN61000-4-11 (1994): Voltage Dip and Interrupt immunity Criteria A.

Declaration of Conformity based on tests conducted by Chomerics Test Services, Woburn, MA 01801, USA in
September, 2001. Test records are outlined in Chomerics Test Report #EMI3053.01.

We hereby declare that the equipment specified conforms to the above Directives and Standards.

Carl Haapaoja, Director of Quality Assurance

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Measurement Computing Corporation

10 Commerce Way

Suite 1008

Norton, Massachusetts 02766

[phone]

Fax: [phone]

E-mail: [e-mail]

www.mccdaq.com

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Artisan Technology Group is your source for quality

new and certied-used/pre-owned equipment

• FAST SHIPPING AND

DELIVERY

• TENS OF THOUSANDS OF
IN-STOCK ITEMS

• EQUIPMENT DEMOS

• HUNDREDS OF
MANUFACTURERS

SUPPORTED

• LEASING/MONTHLY
RENTALS

• ITAR CERTIFIED
SECURE ASSET SOLUTIONS

SERVICE CENTER REPAIRS

Experienced engineers and technicians on staff
at our full-service, in-house repair center

Instra

Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com

Contact us: (888) 88-SOURCE | [e-mail] | www.artisantg.com

SM

REMOTE INSPECTION

View

WE BUY USED EQUIPMENT

Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins

www.artisantg.com/WeBuyEquipment

LOOKING FOR MORE INFORMATION?

Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical

specications, manuals, and documentation