Measurement DADP-5037 User Manual
PORT A_0 1
PORT A_2
PORT A_4
PORT A_6
PORT B_0
PORT B_ 2
PORT B_ 4
PORT B_ 6
PORT C_ 0 1
PORT C_ 2
PORT C_ 4
PORT C_ 6
PASS_1 25
PASS_3 27
PASS_5 2
PASS_7
PASS_9
PASS_11
PASS_13
PASS_15
PASS_17
PASS_19
PASS_21
PASS_23
PASS_25
P1
2 PORT A_1
4
3
5
7
9
11
13
15
7
19
21
23
9
31
33
35
37
39
41
43
45
47
49
PORT A_3
6
PORT A_5
8
PORT A_7
10
PORT B_1
12
PORT B_3
14
PORT B_5
16
PORT B_7
18
PORT C_1
20
PORT C_3
22
PORT C_5
24
PORT C_7
26 PASS_2
28
PASS_4
30
PASS_6
32
PASS_8
34
PASS_10
36
PASS_12
PASS_14
38
PASS_16
40
PASS_18
42
PASS_20
44
PASS_22
46
PASS_24
48
GND
50
DADP-5037 Connection Guide
U1
+5V Reg.
1 2 3
IN
OUT
GND
PORT A_0 37
PORT A_1
PORT A_2
PORT A_3
PORT A_4
PORT A_5
PORT A_6
PORT A_7
PORT C_0
PORT C_1
PORT C_2
PORT C_3
PORT C_4
PORT C_5
PORT C_6
PORT C_7
GND
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
P2
19 n/c
18 n/c
17 n/c
n/c
16
n/c
15
n/c
14
n/c
13
n/c
12
n/c
11
PORT B_0
10
PORT B_1
9
PORT B_2
8
PORT B_3
7
PORT B_4
6
PORT B_5
5
PORT B_6
4
PORT B_7
3
n/c
2
n/c
1
PORT A_0 1
PORT A_2
PORT A_4
PORT A_6
PORT B_0
PORT B_ 2
PORT B_ 4
PORT B_ 6
PORT C_ 0 1
PORT C_ 2
PORT C_ 4
PORT C_ 6
PASS_1 25
PASS_3 27
PASS_5 2
PASS_7
PASS_9
PASS_11
PASS_13
PASS_15
PASS_17
PASS_19
PASS_21
PASS_23
PASS_25
P3
2 PORT A_1
3
5
7
9
11
13
15
7
19
21
23
9
31
33
35
37
39
41
43
45
47
49
4
PORT A_3
6
PORT A_5
8
PORT A_7
10
PORT B_1
12
PORT B_3
14
PORT B_5
16
PORT B_7
18
PORT C_1
20
PORT C_3
PORT C_5
22
PORT C_7
24
26 PASS_2
PASS_4
28
PASS_6
30
PASS_8
32
PASS_10
34
PASS_12
36
PASS_14
38
PASS_16
40
PASS_18
42
PASS_20
44
PASS_22
46
PASS_24
48
GND
50
signal conditioning and accessory boards. The DADP-5037 connects the digital I/O bits
from the PCI board’s 100-pin I/O connector to those external accessory and signal
conditioning boards using 37D I/O-type connectors.
Notes:
# Connector P1 and P3 are wired 1:1, which allows either connector to be used as the
main interface between the PCI board and the DADP-5037. The unused 50-pin
connector can be used for applications that require you to monitor the I/O signals of
the connector in use. Consult your DAS manual’s I/O connector pin assignment
section to verify which signals are available at the connector being monitored.
# Position U1 is reserved for the installation of a voltage regulator
(MCC p/n TN-MC78M05CT). The voltage regulator should only be used with
accessory boards that are powered through the 37D connector, such as the
SSR-RACK08 board.
The DADP-5037 adapter board allows PCI analog I/O boards to interface and control
DADP-5037 Connector Map.cdr
© 2003 Measurement Computing Corporation
C100FF-X
51-100 Cable
P3
P1
DADP-5037
To accessory board’s
37D I/O connector
P2
Document Revision 2
Loading...