MEANWELL MW PLP-20-48 Datasheet

SPECIFICATION

MODEL

DC VOLTAGE

CONSTANT CURRENT REGION Note.5

RATED CURRENT

CURRENT RANGE

CURRENT ADJ. RANGE

RATED POWER

OUTPUT

INPUT

PROTECTION

ENVIRONMENT

SAFETY &

EMC

NOTE

RIPPLE & NOISE (max.) Not e.2

VOLTAGE TOLERANCE Note.3

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME

VOLTAGE RANGE Note.4

FREQUENCY RANGE

POWER FACTOR

EFFICIENCY(Typ.)

AC CURRENT

INRUSH CURRENT( )Typ.

LEAKAGE CURRENT

OVER CURRENT Note.5

SHORT CIRCUIT

OVER VOLTAGE

OVER TEMPERATURE

WORKING TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

SAFETY STANDARDS

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

EMC EMISSION

EMC IMMUNITY

MTBF

DIMENSIONOTHERS

PACKING

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltage, please check the static characteristic for more details.

5. Please refer to "DRIVING METHODS OF LED MODULE".

6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.

8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains.

20W Single Output LED Power Supply

■ Features :

‧Universal AC input / Full range(up to 277VAC)
‧Protections:Short circuit/Over current/Over voltage/Over temperature
‧Cooling by free air convection
‧Built-in constant current limiting circuit with adjustable OCP level
‧Built-in active PFC function
‧ Ⅱ
‧Small and compact size
‧100% full load burn-in test
‧High
‧Suitable for built-in applications of LED lighting
‧2 years warranty

PLP-20-12

12V

9 ~ 12V

1.6A

0 ~ 1.6A

75% ~ 100%

19.2W

2.5Vp-p

±10%
±3.0%
±10%

500ms / 230VAC 20 at full load00ms / 115VAC

90 ~ 277VAC 127~392VDC

47 ~ 63Hz

PF≥0.9 at 75~100% load, 115VAC/230VAC;PF≥0.9 at 85~100% load 277VAC (Please refer to "Power Factor Characteristic" curve)
80%

0.4A/115VAC 0.2A/230VAC 0.15A/277VAC

COLD START 25A(twidth=60 s measured at 50% Ipeak) at 230VACμ

0.5mA / 240VAC

95 ~ 110%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

Hiccup mode, recovers automatically after fault condition is removed.

14 ~ 16V

Protection type : Shut off o/p voltage, clamping by zener diode

Shut down o/p voltage, recovers automatically after temperature goes down

-30 ~ +60℃ (Refer to "Derating Curve")

20 ~ 90% RH non-condensing

-40 ~ +80℃, 10 ~ 95% RH
±0.06%/℃ (0 ~ 50℃)

10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes

TUV EN61347-1, EN61347-2-13, UL8750,CSA C22.2 No. 250.0-08 approved

I/P-O/P:3.75KVAC

I/P-O/P:100M Ohms/500VDC / 25℃/ 70%RH
Compliance to EN55015, EN61000-3-2 Class C(≧75% load); EN61000-3-3

Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, light industry level, criteria A

643.6Khrs min. MIL-HDBK-217F (25℃)

140*32*22(L*W*H)

0.12kg;60pcs/9.2kg/0.62CUFT

PLP-20-18

18V

13.5 ~ 18V

1.1A

0 ~ 1.1A

19.8W

3.0Vp-p

81%

19 ~ 22V

Class power unit, no FG

reliability,low cost

PLP-20-24

24V

18 ~ 24V

0.8A

0 ~ 0.8A

19.2W

3.0Vp-p

82%

27 ~ 34V

PLP-20 se r i es

..

PLP-20-36

36V

27 ~ 36V

0.55A

0 ~ 0.55A

19.8W

3.0Vp-p

83%

41 ~ 46V

PLP-20-48

48V

36 ~ 48V

0.42A

0 ~ 0.42A

20.2W

3.8Vp-p

83.5%

54 ~ 60V

Fil e Name: PLP-2 0-SPE C 2014- 01-09

20W Single Output LED Power Supply

PLP-20 se r i es

Mechanical Specification

5~8

(BR OWN)

(BL UE)

300±1 0

UL 1015 18 AWG

Unit:mm

140

3.5

3.5

AC/L

32

25

AC/N

133

+V

-V

22

300±1 0

UL 1015 18 AWG

5~8

(RE D)

(BL ACK)

Block Diagram

I/P

EMI F ILTER

&

REC TIFIE RS

O.L .P.

Derating CurveDerating Curve

100

100

80

80

60

60

40

40

LOAD (%)

LOAD (%)

LOAD (%)

20

20

-25 -5 0 15 30

-25 -5 0 15 30 40 50

-30 60

POW ER

SWI TCHIN G

PWM & P FC

CON TROL

(HORIZONTAL)

REC TIFIE RS

&

FILT ER

O.C .P.

DET ECTIO N

CIR CUIT

O.V.P.

Static Characteristics

100

90

80

70

60

50

LOAD (%)

40

90 100 125 135 145 1 55 165 175 180 200 230 277

+V

-V

AMBIENT TEMPERATURE (℃)

INPUT VOLTAGE (V) 60Hz

Fil e Name: PLP-2 0-SPE C 2014- 01-09

20W Single Output LED Power Supply

0.78

0.80

0.82

0.84

0.86

0.88

0.90

0.92

0.94

0.96

0.98

1.00

50% 60% 70% 80% 90% 100%

277Vac

230Vac

115Vac

42

46

50

54

58

62

66

70

74

78

82

86

90

10% 20% 30% 40% 50% 60% 70% 80% 90% 100%

277Vac

230Vac

115Vac

Vo(%)

100

75

50 100

(max.)

Io (%)

Constant

Current area

Hiccup

Protection

Power Factor Characteristic

Power factor wil l be higher than 0.9 wh en o utput loading i s 75 % or higher.

Constant Current Mode

PF

(20W)

LOAD

EFFICIENCY vs LOAD (48V Model)

PLP-20 series po ssess superior wo rking efficiency that u p to 8 3.5% can be reach ed i n field applica ti ons.

PLP-20 se r i es

EFFICIENCY (%)

LOAD

DRIVING METHODS OF LED MODULE

This LED power sup ply is suggested to w ork in constant cur re nt mode area (CC) t o dr ive the LEDs.

Typical LED power s upply I-V curve

In the constant cu rrent region, the h ighest voltage at t he o utput of the driv er
depends on the con figuration of the e nd systems.

Should there be an y compatibility i ssues, please con tact MEAN WELL.

Fil e Name: PLP-2 0-SPE C 2014- 01-09