MEANWELL MW PLM-12E-700 Datasheet

12W Single Output LED Power Supply

110

MM

F

SELV

IP30

PLM-12 series

(for Blank type only)

■ Features ■ Applications
230VAC only or Full range (up to 295VAC)

models available

Built-in active PFC function
Constant current design

Indoor LED lighting
LED office lighting
LED commercial lighting

LED decorative lighting
Protections:Short circuit
Cooling by free air convection
Fully isolated plastic case
Class power unit, no FGⅡ
Class 2 power unit (Blank type only)
No load power consumption <0.5W
High reliability,low cost
2 years warranty

18

■ Description

PLM-12 is a 12W economical AC/DC LED power supply series. Incorporating a built-in active PFC
design, PLM-12 provides a high Power Factor value greater than 0.9. In addition, with the low no load
power consumption below 0.5W, and the setup time less than 500ms, PLM-12 is complied with the ErP
regulation required by European Union for lighting fixtures.

PLM-12 is a class (without FG pin) power unit housed with the UL 94V-0 rated flame retardantⅡ
plastic case. The /O terminals are designed with screw-less clamp style terminal block that greatlyI
simplifies the wiring installation. Two types of models with different input voltage range are offered:
PLM-12 series, which operates from 110~295VAC, and PLM-12E series, which operates from
180~295VAC.These two series are both constant current output design, supplying models with the

current of 350mA, 500mA, 700mA and 1050mA, respectively.

■ Model Encoding

- 350PLM - 12

E

Output current

Blank: AC input range 110~295VAC

{

E:AC input range 180~295VAC

Output wattage

Series name

File Name:PLM-12-SPEC 2015-06-03

SPECIFICATION

MODEL

CONSTANT CURRENT REGION

RATED CURRENT

NO LOAD OUTPUT VOLTAGE

OUTPUT

INPUT

RATED POWER

RIPPLE & NOISE

(max.)

CURRENT ACCURACY

SETUP TIME

VO LTAGE RA NG E

FREQUENCY RANGE

POWER FACTOR

TOTALHARMONIC
DISTORTION

EFFICIENCY
(Typ.)

AC CURRENT

INRUSH CURRENT(Typ.)

MAX. No. of PSUs on 16A
CIRCUIT BREAKER

12W Single Output LED Power Supply

PLM-12 -500

15 ~ 24V

0.5A

30V

12W

2.4Vp-p

3.6Vp-p

84%

83%

Note.2

Note.5

(max.)

Blank type

E type

Note.3

Note.4

Blank type

E type

Blank type

E type

Blank type

E type

PLM-12 -350

22 ~ 36V

0.35A

42V

12.6W

3.6Vp-p

5.5Vp-p

±5.0%

Blank type: 500ms / 115VAC, 230VAC at full load; E type: 500ms / 230VAC at full load

Blank type: 110 ~ 295VAC 156 ~ 417VDC; E type: 180 ~ 295VAC 254~ 417VDC

47 ~ 63Hz

PF 0.97/115VAC,PF 0.95/230VAC,PF>0.9/277VAC(at full load)(Please refer to "Power Factor Characteristic" curve)≥≥

PF 0.95/230VAC,PF 0.9/277VAC (at full load)(Please refer to "Power Factor Characteristic" curve)≥≥

THD< 20% when output loading 60% at 115VAC/230VAC input and output loading 75% at 277VAC input≧≧

THD< 20% when output loading 60% at 230VAC input and output loading 75% at 277VAC input≧≧

85%

84%

Blank type: 0.15A/115VAC 0.08A/230VAC 0.07A/277VAC; E type: 0.08A/230VAC 0.07A/277VAC

COLD START 15A(twidth=50 s measured at 50% Ipeak) at 230VACμ

160 units (circuit breaker of type B) / 160 units (circuit breaker of type C) at 230VAC

PLM-12 -700

11 ~ 18V

0.7A

22V

12.6W

2.4Vp-p

3.6Vp-p

83%

82%

PLM-12 series

PLM-12 -1050

7 ~ 12V

1.05A

16V

12.6W

1.8Vp-p

2.7Vp-p

81%

78%

LEAKAGE CURRENT

PROTECTION

SHORT CIRCUIT

WORKING TEMP.

WORKING HUMIDITY

ENVIRONMENT

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

SAFETY STANDARDS

SAFETY &
EMC

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

EMC EMISSION

EMC IMMUNITY

MTBF

OTHERS

DIMENSION

PACKING

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Please see AC input voltage drop vs. output current characteristics table.""

4. Derating may be needed under low input voltage, please check the static characteristic for more details.

5. Constant current operation region is within 60% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please

6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the

7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.

0.25mA / 240VAC

Hiccup mode, recovers automatically after fault condition is removed.

-30 ~ +50℃

20 ~ 90% RH non-condensing

-40 ~ +80 , 10 ~ 95% RH℃

±℃ ℃0.06%/ (0 ~ 50 )

10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes

UL8750, CSA C22.2 No. 250.13-12(for Blank type only); ENEC EN61347-1, EN61347-2-13, EN62384, IP30 approved

I/P-O/P:3.75KVAC

I/P-O/P:100M Ohms/500VDC / 25 / 70%RH℃

Compliance to EN55015,EN61000-3-2 Class C( 60% load);EN61000-3-3≥

Compliance to EN61000-4-2,3,4,5,6,8,11;EN61547, light industry level, criteria B(surge 2KV)

808.162Khrs min. MIL-HDBK-217F (25 )℃

145*38*22mm (L*W*H)

0.126Kg;60pcs/8.6 Kg/0.48CUFT

reconfirm special electrical requirements for some specific system design.

complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

File Name:PLM-12-SPEC 2015-06-03

12W Single Output LED Power Supply

PLM-12 series

Mechanical Specification

1

2

4.5

TB1

Case No.PLM-25 Unit:mm

145

4.5

3.5

ψ

4.5

Tcase

4.5

3.5

※ Tcase: Max. Case Temperature.

65

12

38

22

NOTE: The input and output line for using UL1015 18AWG*2C is suggested

Terminal Pin No. Assignment (TB1) :
SWITCHLAB MWX201-75002EB(GRAY)

Pin No. Pin No.

Assignment Assignment

AC/L +V

11

AC/N -V

22

Terminal Pin No. Assignment (TB2) :
SWITCHLAB MWX201-75002B(BLUE)

2

1

TB2

Block Diagram

I/P

EMI FILTER

Derating CurveDerating Curve

100

100

80

80

60

60

40

40

LOAD (%)LOAD (%)

LOAD (%)

20

20

RECTIFIERS

POWER

SWITCH-

ING

PWM /PFC
CONTROL

RECTIFIERS

&

FILTER

Static Characteristics

100

90

80

70

60

50

LOAD (%)

40

+V

-V

-25 -5 0 15 30

-25 -5 0 15 30 40 50

-30 60

AMBIENT TEMPERATURE ( )℃

(HORIZONTAL)

110 120 125 135 145 155 165 175 180 200 230 295

180 185 190 195 200 205 210 220 230 240 295215

INPUT VOLTAGE (V)

File Name:PLM-12-SPEC 2015-06-03

(Blank type)
(E type)

0.8

0.82

0.84

0.86

0.88

0.9

0.92

0.94

0.96

0.98

1

1.02

60% 70% 80% 90% 100%

110V

230V

277V

12W Single Output LED Power Supply

0.82

0.84

0.86

0.88

0.9

0.92

0.94

0.96

0.98

60% 70% 80% 90% 100%

230V

277V

79

80

81

82

83

84

85

86

60% 70% 80% 90% 100%

230V

277V

79

80

81

82

83

84

85

86

60% 70% 80% 90% 100%

110V

230V

277V

Power Factor Characteristic

PLM-12 series

Constant Current Mode

PF

LOAD

Blank type

EFFICIENCY vs LOAD (500mA Model)

(12W)

PF

Constant Current Mode

LOAD

E type

(12W)

EFFICIENCY (%)

LOAD

Blank type

AC input voltage drop vs. output current characteristics

AC input drop

Io drop

NOTE: Output current will return to the rated value within 50ms

10%

<15%

8%

<11%

5%

<7%

EFFICIENCY (%)

LOAD

E type

3%

<6%

File Name:PLM-12-SPEC 2015-06-03