Page 1
600W Single Outp ut Switching Power S upply
5
HEP-600
■ Features ■ Applications
Universal AC input / Full range
‧
Built-in active PFC function
‧
No load power consumption <0.5W at remote OFF
‧
High efficiency up to 96%
‧
Fanless design, cooling by free air convection
‧
Output voltage and output current can be adjusted through internal
‧
potentiometer
Aluminum case and filling with heat-conducted glue
‧
-40 ~ +70 wide operating range℃
‧
Withstand 300VAC surge input for 5 seconds
‧
Withstand 5G vibration test
‧
Protections: Short circuit / Over current / Over voltage
‧
/ Over temperature
LED indicator for power on
‧
5 years warranty (Note.7)
‧
Humid and dusty industrial environment
‧
Outdoor telecommunication equipment
‧
No fan environment
‧
Signboard or billboards
‧
Bauar
Sicherheit
egel gema
od
be
wac g
www.
ID 2000000000
se r i e s
tgep ruft
o s
tuv.com
■ Description
HE P-600 series is a h igh-e fficiency and waterproof AC-to-DC indus trial power supply up to 600W, fully
potted by silicone and enclosed with the aluminum case. With state of the art d e sig n, H E P - 6 0 0 w o rks
outstandingly with electronics under hars h environment: fan-less, high-vibration, dusty, humid, and oily
environment. Remarkable features include supreme efficiency up to 96%, low no-load power consumption
(<0.5W) at remote OFF, and wide working temperature ranges between -40 and +70 .℃ ℃
■ Model Encoding
HEP -- 600 12
Output voltage
Output wattage
Series name
Fil e Name: HEP-6 00-SP EC 2015 -01-1 5
Page 2
SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
RATED PO WER
RIPPLE & NOI SE (max.)
VOLTAGE ADJ. RANGE
OUTPUT
INPUT
PROTECTION
FUNCTION
ENVIRONM ENT
SAFETY &
EMC
(
Note.6)
NOTE
CURRENT ADJ. RANGE
VOLTAGE TOLERANCE
LINE R EGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
FREQUENC Y RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CUR RENT (Typ.)
INRUSH CURRENT(Typ.)
LEAKAGE CURRENT
OVER CURRENT
SHORT CIRCUIT
OVER VOLTAGE
OVER TEMPERATURE
REMOTE ON/OFF CONTROL
5V STANDBY
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMC EMISSION
EMC IMMUNITY
MTBF
DIMENSIONOTHERS
PACKING
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltages. Please check the static characteristics for more details.
5. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
7. Refer to warranty statement.
600W Single Outp ut Switching Power S upply
HEP-600-12 HEP-600-15 HEP-600-20 HEP-6 00-2 4 HEP-600-30 HEP-6 00-36 HEP-600-42 HEP-600-48 HEP-600-54
12V
40A 36A 28A 25A
480W 540W 560W 600W 600W
150mVp-p 150mVp-p
Note. 2
Can be adjusted by internal potentiometer
20 ~ 40A
±3.0%
Note. 3
±0.5% ±0.5% ±0.5% ±0.5% ±0.5%
±2.0%
Note.5
500ms, 80ms at full load 230VAC /115VAC
15ms at full load 230VAC /115VAC
Note.4
90 ~ 264VAC 127 ~ 373VDC
47 ~ 63Hz
PF>0.98/115VAC, PF>0.95/230VAC at full load
93%
7A / 115VAC 3.3A / 230VAC
COLD START 70A(t =1000 s measured at 50% I ) at 230VAC
<0.75mA / 240VAC
105 ~ 125%
Protection type : Constant current limiting, recovers aut omatically after fault condition is removed
Constant current limiting, recovers automatically after fault condition is removed
13 ~ 16V 16.5 ~ 20.5V
Protection type : Shut down o/p voltage, re-power on to recover
Shut down o/p voltage, re-power on to recover
Power on : "Hi" >2 ~ 5V or Open circuit Power o ff : "Low" <0 ~ 0.5V or Short circuit
5V : 5V@0.5A ; tolerance 5%, ripple : 100mVp-p(max.)
SB
-40 ~ +70 (Refer to "Derating Curve" )℃
20 ~ 95% RH non-condensing
-40 ~ +85 , 10 ~ 95% RH℃
± ℃ ℃0.03%/ (0 ~ 60 )
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
UL60950-1, TUV EN60950-1 approved
I/P-O /P:3KVAC I/P-FG:2K VAC O/P -F G: 1.5K VAC
I/P-O /P, I/P-FG, O/P-FG:100M O hms / 50 0VDC / 2 5 / 70% RH℃
Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, heavy industry level, criteria A
76.9K hrs min. MIL-HDBK-217F (25 )℃
280*144*48.5mm (L*W*H)
3.9Kg; 4pcs/16.6Kg/0.9CUFT
15V 20V 24V 30V
150mVp-p
12.7 ~ 15.8V
18 ~ 36A
±2.0%
±1.5% ±1.0% ±0.5% ±0.5%
94%
17 ~ 21V
14 ~ 28A
±1.5%
95%
width peak
μ
22 ~ 26V
±
150mVp-p
20.4 ~ 25.2V
12.5 ~ 25A
±1.0%
95%
26 ~ 30V
20A
200mVp-p
25.5 ~ 31.5V
10 ~ 20A
±1.0%
95.5%
32.5 ~ 36.5V
HEP-600
36V
16.7A
601.2W
250mVp-p
30.6 ~ 37.8V
8.3 ~ 16.7A
±1.0%
±0.5%
±0.5%
95.5%
39.5 ~ 43.5V 52.5 ~ 56.5V
42V
14.3A
600.6W
250mVp-p
35.7 ~ 44.1V
7.1 ~ 14.3A
±1.0%
±0.5%
±0.5%
46 ~ 50V 59 ~ 63V
48V
12.5A
600W
250mVp-p
40.8 ~ 50.4V10.2 ~ 12.6V
6.2 ~ 12.5A
±1.0%
±0.5%
±0.5%
96%96% 96%
se r i e s
54V
11.2A
604.8W
350mVp-p
45.9 ~ 56.7V
5.6 ~ 11.2A
±1.0%
±0.5%
±0.5%
Fil e Name: HEP-6 00-SP EC 2015 -01-1 5
Page 3
Block Diagram
I/P
EMI FILT ER
RECTI FIERS
600W Single Outp ut Switching Power S upply
POW ER SWIT CHI NG
PWM CONTROL
&
PFC
CIR CUIT
POW ER
SWI TCHI NG
+5VSB
DETECT ION
CIRCUIT
RECTI FIERS
&
FILTER
RECTI FIERS
&
FILTER
HEP-600
fosc : 70 KHz
O.L.P.
se r i e s
+5VSB
+V
-V
FG
PFC
CONTR OL
O.L.P.
PWM & PFC
CONTR OL
Derating Curve Static Characteristics
100
80
60
40
20
-40 -25 -10 0 15 30 50 5 5 60 70
AMBIENT TEMPERATURE ( )℃ INPUT VOLTAGE (V) 60Hz
(HORI ZONTAL)
100
90
80
70
60
50
40
90 115 125 135 145 155 165 175 180 200 230 264
DETEC TION
CIR CUIT
O.V.P.
PS/ ON
CON TROL
PS/ ON
Fil e Name: HEP-6 00-SP EC 2015 -01-1 5
Page 4
600W Single Outp ut Switching Power S upply
HEP-600
se r i e s
Mechanical Specification
I/P
5.7
21m ax.
13.4
8.9
5.7
1
2
3
ψ ×4.5 4P L
ψ ×6 4PL
※ T cas e: Max. Case Temp erat ure.
280
253 .2
T cas e
268 .6
126 .6
Io
ADJ .VoADJ .
Case No . 228A Unit:mm
1
2
3
4
5
6
7
LED
21m ax.
O/P
※ Output v oltage and constant c ur rent level can be adjusted through internal poten tiometer.
(Can acc es s by removing the rub ber stopper on the case.)
AC In pu t Termina l Pin No. Assignment DC Outp ut Terminal Pin No. Ass ignment
Pin No.
Ass ignment
1
FG
2
AC/L
3
AC/N
Installation Manual
Please refer to : http://www.meanwell.com/we bnet/se arch/Inst allat ionSe ar ch.html
Pin No. Pin No.
Ass ignment Ass ignment
1 4,5
RC+ -V
2
3
RC- & GND
+5V
6,7
SB
+V
Fil e Name: HEP-6 00-SP EC 2015 -01-1 5
Loading...