MEANWELL FDL-65-1550 Datasheet

65W Constant Current Mode LED Driver

F

FDL-65 series

110

SELV

IP65

■ Features ■ Applications


Constant Current mode output

Metal housing design
Built-in active PFC function

LED flood lighting
LED decorative lighting
LED architectural lighting

 <0.5WNo load power consumption
IP65 rating for indoor or outdoor installations
Output current adjustable via potentiometer
3 years warranty

■ Description

FDL-65 series is a 65W LED AC/DC LED power supply featuring the constant current mode output,
targeting at but not limited to LED flood lighting applications. FDL-65 operates from 180 295VAC～
and offers models working perfectly for the voltage up to 42V (1550mA model) and 36V(1800mA model).

Thanks to the high efficiency up to 90%, with the fanless design, the entire series is able to operate
for -40 ~ +90 case temperature under free air convection. The design of metal housing and IP65℃℃
ingress protection level allows this series to fit both indoor and outdoor applications. FDL-65 is

equipped with output current adjustable function so as to provide the optimal design flexibility for
LED lighting system.

■ Model Encoding

- 1800FDL -

65

Rated output current (1550/1800mA)
Rated wattage

Series name

File Name:FDL-65-SPEC 2016-04-20

SPECIFICATION

MODEL

RATED CURRENT

RATED POWER

CONSTANT CURRENT REGION

OUTPUT

INPUT

PROTECTION

ENVIRONMENT

SAFETY &
EMC

OTHERS

NOTE

OPEN CIRCUIT VOLTAGE

CURRENT ADJ. RANGE

CURRENT TOLERANCE

SET UP TIME

VO LTAGE RAN GE

FREQUENCY RANGE

POWER FACTOR

TOTALHARMONIC DISTORTION

EFFICIENCY (Typ.)

AC CURRENT(Typ.)

INRUSH CURRENT

MAX. No. of PSUs on 16A
CIRCUIT BREAKER

LEAKAGE CURRENT

NO LOAD POWER CONSUMPTION

SHORT CIRCUIT

OVER VOLTAGE

OVER TEMPERATURE

WORKING TEMP.

MAX. CASE TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

SAFETY STANDARDS

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

EMC EMISSION

EMC IMMUNITY

MTBF

DIMENSION

PACKING

1. All parameters NOT specially mentioned are measured at 230VAC input, rated and 25 of ambient temperature.current ℃

2. Please refer to "DRIVING METHODS OF LED MODULE".

3. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.

4. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

65W Constant Current Mode LED Driver

FDL-65-1550

1550mA

65.1W

Note.2

25.2 ~ 42V

50V

(max.)

0.77-1.55A

±5.0%

Note.3

(Typ.)

500ms/230VAC

180 ~ 295VAC 254 ~ 417VDC

(Please refer to "STATIC CHARACTERISTIC" section)

47 ~ 63Hz

PF 0.95/230VAC, PF 0.90/277VAC@full load≧≧
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)

THD< 20%(@load 60%/230VAC; @load 75%/277VAC)≧≧
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)

90%

0.48A / 230VAC 0.39A/277VAC

(Typ.)

COLD START 50A(twidth= s measured at 50% Ipeak)/230VAC270 Per NEMA 410μ;

28 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC

<0.75mA / 277VAC

<0.5W
Hiccup mode, recovers automatically after fault condition is removed

46 ~ 56V
Shut down o/p voltage, re-power on to recover

Hiccup mode, recovers automatically after fault condition is removed

Tcase=-40 ~ +90 (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)℃

Tcase=+90℃

20 ~ 95% RH non-condensing

-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 60 )

10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes

LVD EN61347-1,EN61347-2-13 Independent, GB19510.1,GB19510.14,IP65 approved

I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH℃
Compliance to EN55015, EN61000-3-2 Class C (load 60%) ; EN61000-3-3,GB17743,GB17625.1≧

Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level(surge immunity:Line-Earth:4KV,Line-Line:2KV)

594.9K hrs min. MIL-HDBK-217F (25 )℃

151*53*31.5mm (L*W*H)

0.42Kg; 24pcs / 11.08Kg / 0.73CUFT

FDL-65 series

FDL-65-1800

1800mA

64.8W

21.6 ~ 36V

45V

0.9~1.8A

90%

40 ~ 48V

File Name:FDL-65-SPEC 2016-04-20

65W Constant Current Mode LED Driver

BLOCK DIAGRAM

FDL-65 series

PWM fosc : 60~130KHz

I/P

EMI FILTER

&

RECTIFIERS

O.V.P.

O.L.P.O.T.P.

CASE GROUND

POWER

SWITCHING

DRIVING METHODS OF LED MODULE

※ This series works in constant current mode to directly drive the LEDs.

100

Constant

Vo(%)

60

(min.)

Current area

Hiccup

Protection

RECTIFIERS

&

FILTER

DETECTION

PWM & P FC

CONTROL

In the constant current region, the highest voltage at the output of the driver
depends on the configuration of the end systems.

Should there be any compatibility issues, please contact MEAN WELL.

CIRCUIT

+V

-V

50

Typical output current normalized by rated current (%)

100

Io(%)

File Name:FDL-65-SPEC 2016-04-20

0%

5%

10%

15%

20%

25%

60% 70% 80% 90% 100%

277VAC

230VAC

88

88.5

89

89.5

90

90.5

91

91.5

60% 70% 80% 90% 100%

277V

230V

0.8

0.82

0.84

0.86

0.88

0.9

0.92

0.94

0.96

0.98

60% 70% 80% 90% 100%

277V

230V

65W Constant Current Mode LED Driver

OUTPUT LOAD vs TEMPERATURE

FDL-65 series

100

80

60

40

LOAD (%)

20

-40 -25 0-10 15 30 50 60 70

AMBIENT TEMPERATURE,Ta ( )℃

STATIC CHARACTERISTIC

100

90

80

70

60

50

LOAD (%)

40

(HORIZONTAL)

100

80

60

40

LOAD (%)

20

-40-250 204555657590

Tcase ( )℃

POWER FACTOR (PF) CHARACTERISTIC

※ Tcase at 80℃

PF

(HORIZONTAL)

180 190 200 210 220 230 240 260 270 280 295

INPUT VOLTAGE (V) 60Hz

TOTAL HARMONIC DISTORTION (THD)

※ 1800mA Model,Tcase at 80℃

THD

LOAD

250

LOAD

EFFICIENCY vs LOAD

FDL-65 series possess superior working efficiency that up to 90% can
be reached in field applications.

※ 1800mA Model, Tcase at 80℃

EFFICIENCY(%)

LOAD

File Name:FDL-65-SPEC 2016-04-20

65W Constant Current Mode LED Driver

MECHANICAL SPECIFICATION

150±20

AC/N(Blue)

AC/L(Brown)

H05RN 1.0mm²*2C

4 4.5xψ
4 7.5xψ

151

142

140

127

7

tc

tc

 : Max. Case Temperature

FDL-65 series

CASE NO.: 246A Unit:mm

150±20

22

-V(Blue)

24.5

43

31.5

53

H05RN 1.0mm²*2C

+V(Brown)

◎ Note: Please connect the case to FG for the complete EMC deliverance.

INSTALLATION MANUAL

Please refer to : http://www.meanwell.com/webnet/search/InstallationSearch.html

34.29

12.63

File Name:FDL-65-SPEC 2016-04-20