Meaco 1056 P User guide

MeacoFan 1056P Air Circulator

Instruction Manual

MeacoFan 1056P Air Circulator

Please read this instruction manual before using the air circulator and keep safe for

future reference.

Thank you for choosing Meaco, we really appreciate it.

SAFETY INFORMATION

---------------------------------------------------------------------------------------------------------------------------------------

This air circulator must not be used in rooms under the following conditions:

- Potentially explosive atmosphere

- Aggressive atmospheres

- Featuring a high concentration of solvents

- An extremely high ratio of dust

- Commercial environments

Magnets: The air circulator and the remote control both contain magnets. Please note the following:
Pacemakers and defibrillators may be affected by magnets. If this affects you then please do not put
the remote control in a pocket and warn anyone who is likely to use the air circulator or the remote that
it has a magnet. Credit cards and data cards can also be affected by magnets and should not be placed
near to the air circulator or the fan.

Keep Children Away: Do not allow children to play with or around this unit, which could result in injury.
Be sure the unit is inaccessible to children when not attended. This appliance is not intended for use by
person (including children) with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety.

Keep Unit Grounded: Always operate the unit with a grounding plug and a grounded electrical outlet.
A grounding plug is an essential safety feature that helps reduce the risk of shock or fire.

Protect Power Cord from Damage: Never operate a unit with a damaged power cord, as this may
lead to electrical or fire hazards. If the power supply cord is damaged, it must be replaced by a cord of
the same type and amperage rating.

Extension Cords: Extension cords must be grounded and able to deliver the appropriate voltages to
the unit.

Handle with Care: Do not drop, throw or crash the air circulator. Rough treatment can damage the
components or wiring and create a hazardous condition.

Run on Stable Surface: Always operate the unit on a stable, level surface, for example the floor or a
strong counter, so that the air circulator cannot fall and cause injury.

Keep Out of Water: Never operate the unit in pooled or standing water, as this may create a risk of
injury from electrical shock. Do not store or operate outdoors. If electrical wiring or components become
wet, thoroughly dry them before using the unit. If in doubt do not use the air circulator and consult a
qualified electrician or a Meaco approved engineer.

Keep Air Intakes Clear: Do not clog or block the air intakes by placing the air circulator too close to
curtains, walls or anything that will restrict the air inlet. This may cause the unit to overheat and result
in a fire or electrical hazard.

Keep Electrical Components Dry: Never allow water inside the air circulator’s electrical components.
If these areas become wet for any reason, thoroughly dry them before using the air circulator. If in
doubt, do not use the air circulator and consult a qualified electrician or a Meaco approved engineer.

The operator must make the operating instruction available for the user and make sure that the user
does understand the manual.

2

WIRING INSTRUCTIONS

---------------------------------------------------------------------------------------------------------------------------------------

Should it be necessary to change the plug, please note the wires in the mains lead are
coloured in accordance with the following code:

BLUE – NEUTRAL
BROWN – LIVE
GREEN AND YELLOW – EARTH

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:

1. The

BLUE wire is the NEUTRAL and must be connected to the terminal which is marked with

the letter N or coloured BLACK.

2. The BROWN wire is the LIVE and must be connected to the terminal which is marked with

the letter L or coloured

3. The

GREEN/YELLOW is the EARTH and must be connected to the terminal which is marked

with the letter E or coloured

RED.

GREEN or GREEN/YELLOW.

4. Always ensure that the cord grip is positioned and fastened correctly.

5. Only ever use the same fuse as fitted in the original product, if in doubt please contact Meaco

first, or a qualified electrician.

Example wiring for a Standard British Plug:

Please note: The Earth Terminal is marked with the letter E or Earth Symbol .

3

01. Magnetic remote-control holder

02. Front guard

03. Spinner

04. Fan blades

05. Handle*

06. Rear guard

07. Fan motor

08. Motor bracket

09. Support bracket

10. Pedestal release button

11. Pedestal

12. Power cord

13. Base

14. Remote control**

GENERAL ADVICE

---------------------------------------------------------------------------------------------------------------------------------------

• Before putting your air circulator into operation for the first time, the instruction manual should
be studied carefully.

• After receiving the air circulator, you should check the unit for any transport damage. In case
of damage, you should inform the sender immediately.

• Keep the packaging for the air circulator in a safe place in order to be able to despatch the unit
safely if it requires a service. In order to save space, you can simply cut through the adhesive
tape using a knife and fold the cardboard box.

PRODUCT IDENTIFICATION

---------------------------------------------------------------------------------------------------------------------------------------

* The handle is made from artificial materials and does not contain any animal products.
** The remote control is supplied with a CR2025 DC3v battery. Please remove the tab from the battery
before use.

4

Pedestal

release button

Support

bracket

SET UP

---------------------------------------------------------------------------------------------------------------------------------------

The MeacoFan 1056P is a pedestal air circulator which can be used at various adjustable heights.

In order to adjust the height of the air circulator press the release button on the back of the pedestal.
Push the release button and lift the air circulator via the support bracket. The air circulator will click into
place at the chosen height. To reduce the height of the air circulator, reverse the process. Push the
release button and press down on the support bracket.

5

POWER BUTTON

When plugged in the air circulator will bleep once and display the room temperature
on the display, this is standby mode. To turn the air circulator on put your finger on
the power button for two seconds. The air circulator will bleep and start to operate.
To turn the air circulator off, put your finger on the power button again for two
seconds, you will hear a longer bleep and the air circulator will slow down and stop.

MODE BUTTON

Press the mode button to move through the four modes: normal, natural, sleep and
ECO.

Normal Mode: This is the default setting on the air circulator. The fan speed can
be adjusted between 1 and 12. The airflow is constant on each fan speed.

Natural Mode: Press the mode button once to reach natural mode – the symbol to
the left will appear on the display. The fan speed can be adjusted between 1 and

12. The airflow will alternate between weak and strong in order to replicate a natural
breeze.

Sleep Mode: Press the mode button twice to reach sleep mode – the symbol to the
left will appear on the display. The fan speed will decrease by one level every 30
minutes. When fan speed 1 has been reached, the fan will continue to run until it is
manually turned off.

ECO Mode: Press the mode button three times to reach ECO mode - the room
temperature will appear on the display. In ECO mode the fan speed will
automatically change as per the table on the following page.

CONTROL PANEL

---------------------------------------------------------------------------------------------------------------------------------------

Please note all the buttons are touch sensitive and bleep when pressed. The buttons need to be pressed quickly,
do not hold your finger on the button for longer than one second (unless when turning the air circulator ON/OFF,
see below). Do not operate the controls on the base of the air circulator with your feet.

6

Room temperature

Fan speed

<23°C

2

23 to 25°C

4

25 to 27°C

6

27 to 29°C

8

29 to 31°C

9

31 to 33°C

10

>33°C

12

SPEED BUTTON

Press the speed button to adjust the air flow fan speed. There are 12 fan speeds
available. As long as the air circulator remains plugged in, the air circulator will
remember the last fan speed used. The speed can be adjusted on the control panel
or via the remote control.

VERTICAL AND HORIZONTAL OSCILLATION BUTTONS (OSC)

Press the oscillation buttons to start and stop the sideways oscillation left and right
or up and down. Press the button once to turn the oscillation on and press the button
again to stop the motion, in doing so you can fix the direction of the air circulator.

TIMER BUTTON

When the air circulator is in standby mode use the timer button to set an interval, in
one-hour segments, between 1 and 12 hours after which the air circulator will turn
ON. Once you have reached the desired number of hours on the display the number
will flash four times and then set.

When the air circulator is turned on and running, use the timer button to set an
interval, in one-hour segments, between 1 and 12 hours after which the air circulator
will turn OFF. Once you have reached the desired number of hours on the display
the number will flash four times and then set.

To turn the timer off, press the timer button until 00 is displayed.

ECO Mode

7

LIGHT BUTTON

Press the light button to turn the lights on the display ON/OFF.

INCREASE FAN SPEED

Press the increase fan speed button to increase the air flow fan speed between 1 and 12.

DECREASE FAN SPEED

Press the decrease fan speed button to decrease the air flow fan speed between 12 and 1.

PRE-ON TIMER

Press the pre-on timer button to set an interval, in one-hour segments, between 1 and 12 hours after
which the fan will turn ON. This can only be used when the air circulator is in standby mode.

PRE-OFF TIMER

Press the pre-off timer button to set an interval, in one-hour segments, between 1 and 12 hours after
which the fan will turn OFF. This can only be used when the air circulator is on and running.

POWER BUTTON

PRE- OFF TIMER

PRE-ON TIMER

LIGHT BUTTON

INCREASE FAN

SPEED

DECREASE FAN

SPEED

(LOCATING

DOT)

VERTICAL

OSCILLATION BUTTON

HORIZONTAL

OSCILLATION BUTTON
MODE BUTTON

REMOTE CONTROL

---------------------------------------------------------------------------------------------------------------------------------------

The following functions are only available via the remote control. All other buttons on the remote-control
work in the same way as the control panel (see pages 6 and 7). The remote control has a range of
approximately three metres. Before using the remote control, remove the plastic tab.

8

Operating conditions

+5°C to +40°C

Humidity operating range

Non-condensing

Fan motor type

DC

Maximum air flow

1653 cubic metres per hour

*Maximum air velocity (c)

4m/sec

*Rated voltage and frequency

220 – 240V / 50Hz

Power consumption

6 to 24 watts

*Standby power consumption (PSB)

<0.5 watts

Oscillation swing angles

60° vertically and 80° horizontally

*Fan sound power level (LWA)

20 to 60dB(A)

*Service value (SV)

1.2 (m³/min)/watts

*Fan power input (P)

23 watts

*Maximum fan flow rate (F)

27.56m³/min

Dimensions (HWD)

820-955 x 320 x 339mm

Nett weight

4.7 Kgs

ELECTRICAL CONNECTIONS AND OPERATING CONDITIONS

---------------------------------------------------------------------------------------------------------------------------------------

This air circulator was designed to operate in a 220-240V / 50Hz electrical installation. Make sure that
the electric sockets are connected to earth and that all safety precautions are taken. This air circulator
can be operated within an ambient temperature range from +5°C to +40°C and with a non-condensing
relative humidity.

SPECIFICATIONS

---------------------------------------------------------------------------------------------------------------------------------------

*Measurement Standard for Service Value (all items*): 2009/125/EC, (EU) No 206/2012 + (EU) No 2016/2282, IEC
60879:1986, EN 60704-1:2010 + A11:2012, EN 60704-2-7:1998.

9

CLEANING AND MAINTENANCE

---------------------------------------------------------------------------------------------------------------------------------------

Always turn the air circulator off and unplug it from the socket before cleaning.

Use a soft dry cloth to clean the external and internal parts of the air circulator. Do not allow the air
circulator to get wet. In order to access the fan blades, follow the steps below:

1. Using a screwdriver, unscrew the two small screws at the top back of the air circulator. They
are located directly below each end of the handle.

2. Squeeze the two tabs to the left and right of the screws and pull away. At the front of the fan
blades there is a locking cap – unscrew the cap in a clockwise motion to remove the fan blades.

3. Clean the fan blades and the internal part of the fan using a soft dry cloth. Reverse the
procedure to put the air circulator back together. Make sure the locking cap is tightened
securely.

10

REPLACING THE REMOTE-CONTROL BATTERY

If the remote control fails to work whilst close to the fan, the battery will need replacing. The battery is
a CR2025 and can be replaced following the steps in the diagram below.

STORAGE

---------------------------------------------------------------------------------------------------------------------------------------

When storing the air circulator use the cable compartment at the back of the air circulator to store the
mains cable. The cable compartment cover may be stiff to remove at first – use the small lever at the
top to pull it away from the air circulator.

We recommend storing the fan its plastic bag or original box to protect the air circulator from dust.

Remember the air circulator can also be used in winter to help distribute warm air more effectively within
a room.

11

PROBLEM

CAUSE

SOLUTION

The display shows ‘00’ or

‘99’

There is a problem with the

circuit

Please contact Meaco

The air circulator does not

oscillate

The MPCB needs resetting

Unplug the air circulator from

the mains for 40 minutes

Increased noise level

The fan blades are dirty

Clean the fan blades (see page

10)

The fan blades or fan motor is

loose

Tighten the locking cap (see

page 10)

There is a fault with the fan

motor

Please contact Meaco

The motor can be heard on

the lower fan speeds

As the air circulator is so quiet

it is expected to hear the motor

on the lower fan speeds. As

the fan speed increases, the

noise of the motor will reduce

This is not a fault and is normal

The air circulator does not

start up

The air circulator is in standby

mode

Press the power button again

The air circulator is making a

clicking noise

The air circulator needs

lubricating

Run the air circulator on the

highest fan speed for 4 hours

The remote does not work

The battery needs replacing

Replace the battery (see page

11)

The remote is being used more

than 3m away from the fan

Use the remote closer to the

fan and make sure it is pointing

directly at the fan base

The fan speed increases and

decreases randomly

This is not a fault – the air

circulator is in natural mode

Change the air circulator mode

by pressing the mode button

(see page 6)

TROUBLESHOOTING

---------------------------------------------------------------------------------------------------------------------------------------

12