MD Sports 57000 Installation Guide
INSTRUCCIONESDEARMADO
Do Not Return This Product To The Store
Toll Free: 877-885-1635
www.medalsports.com .tw
No devuelva este producto a su local de venta
N0mero telef6nico gratis: 877-885-1635
www.medalsports.com .tw
MODEUMODELO: 57000
This product is covered by a limited warranty that is effective for
90 days from the date of purchase. The warranty covers any
defects in parts and workmanship.
If, during the limited warranty period, a part is found to be defective
or breaks, we will offer either a free repair or replacement part at no
cost to you, the customer. The only exceptions to the warranty incl-
ude main frames, table tops, playing surfaces, batteries, tools. The
above warranty will not apply in cases of damages due to improper
usage, alteration, mis=use, abuse, accidental damage or neglect.
A PURCHASE RECEIPT (or other proof of purchase date) will be
required before any warranty service is initiated. All requests for
warranty service can be submitted by email, in writing or by con=
tacting our Consumer Service Dept. at:
Toll Free: 877-885-1635
Email: tablegame@medalsports.com.tw
Website: www.medalsports.com.tw
This Limited Warranty gives you specific legal rights and you
may also have other rights which vary from one state (province)
to another.
PLEASE SAVE THESE INSTRUCTIONS
AND PURCHASE RECEIPT!
DO NOT RETURN THIS PRODUCT TO THE STORE!
Please Keep Your Instructions! Your Model number is necessary should you need to contact
us. Please read through this instruction manual book to familiarize yourself with all parts and
assembly steps, kindly refer to the parts identifier below and be sure that all parts have been
included.
Although we are dedicated to giving our customers the best product possible, a question
may arise or parts may be missing. If you are missing parts, or, if you have any questions,
please contact our fast and friendly service centre on :877-885-7635
Phillips Screwdriver- Not Included
Standard (Flat Head Screwdriver)- Not Included
Allen Wrench - Included
Electric Screwdrivers may be helpful during assembly; however, please set a low
torque and use extreme caution because screws may be high. stripped or over-
tightened if the electric screwdriver's torque is set too high.
1- When installing parts that have more than one bolt, hand tighten all bolts before
tightening individual bolts with a screwdriver or allen key.
2- Some figures or drawings may not look exactly like your product. Please read and
understand the text before beginning each assembly step.
OTICE!
READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND SAFETY INSTRUC-
TIONS CAREFULLY. AT LEAST TWO ADULTS ARE NEEDED FOR THE ASSEMBLY
OF THIS TABLE.
THIS IS NOT A CHILD' S TOY. ADULT SUPERVISION IS REQUIRED FOR CHIL-
DREN PLAYING THIS GAME. PLEASE READ INSTRUCTIONS CAREFULLY.
PROPER USE OF THIS SET CAN AVOID DAMAGE OR INJURY.
WARNING" Adult Assembly Required.
i
WARNING"
CHOKING HAZARD - - This item contains small parts.
Not suitable for children under 3 years.
2
PARTS iDENTiFiER
#1
U-Tube
1 Piece
#6
Side Brace
2 Pieces
#11
Back-Upright Tube-C
2 Pieces
#2
Support Tube-A
3 Pieces
#7
"L" Support Tube
2 Pieces
#12
Top Tube
2 Pieces
#3
"L" Base Tube
2 Pieces
#8
Support Tube-B
1 Piece
#13
#4
Connect Tube
2 Pieces
#9
Back-Upright Tube-A
2 Pieces
#14
#5
Base Tube
2 Pieces
#10
Back-Upright Tube-B
2 Pieces
#15
I
O
O
J
Backboard
1 Piece
Rim
1 Piece
Metal Spacer Plate
1 Piece
#16
Electronic Scorer
1 Piece
#21
M6X32MM Bolt
18 Pieces
#26
®
M6 Locknut
26 Pieces
#17 Pre-assembled
Rim Net
1 Piece
#22
M6X20MM Bolt
8 Pieces
#27
Basketball
2 Pieces
#18
Ramp Net
1 Piece
#23
3.0X26MM
Wood Screw
4 Pieces
#28 #29
Allen Key
1 Piece
#19 Pre-assembled
#24
Lock Pin
2 Pieces
12mm Fiat Washer
38 Pieces
Wrench
1 Piece
#20
M6X42MM Bolt
4 Pieces
#25
Switch with
Paddle assembly
1 Piece
#30
Inflation Pump
with Needle
1 Piece
WARNING:
1) Require 4pcs AA Batteries (Not included).
2) Do not mix old and new batteries.
3) Do not mix alkaline, standard (carbon zinc), or rechargeable (nickel-cadmium) batteries.
3
ASSEMBLY iNSTRUCTiONS
1. Find a clean, level place to begin the assembly of your Basketball Game. We recommend
that two adults work together to assembly this basketball game.
2. Remove all the parts from the box and verify that you have all of the listed parts as shown
on the parts identifier below. Carefully cut or tear the four corners of the box so that the
bottom of the box can be used as your work surface.
FIG. I
3. Connect the U-tube (#1) to L Base tubes (#3) by sliding them together and locking in the
place as shown in FIG.1 and 1A.
#1.......
_.. _pring Lock
Detail A
FIG. 2
_#3
4. Connect Side Braces (#6) to Back-Upright Tubes-A (#9) by using one Bolt (#21) and one
Washer (#24) per side as shown in FIG.2.
_ ........ #21
#24
FIG. 3
5. Connect one Support Tube-B (#6) to the tube assembly (#6 and #9) by using two Bolts (#21),
two Washers (#24) and two Locknuts (#26) per side as shown in FIG.3
Note: Make sure all the Bolts (#21) go from the outside toward the center.
J- #9
#26 #2
,\
\
#6
4
FIG. 4
6. Connect BaseTubes (#5) to the assembled Side Braces (#6) by using Bolts (#21) and
Washers (#24) as shown in FIG.4.
#21 #24
FIG. 5
7. Connect Back-Upright tubes-B (#10) to assembled tubes (#9) by sliding them together and
locking in the place as shown in FIG. 5. Then, connect the Tubes (#11) to assembled
tubes (#10) by sliding them together as shown in FIG.5.
8. Connect the upper sides of L Support Tubes (#7) and Support Tube-A(#2) to the tube
assembly (#11 and #10) by using two Bolts (#21), two Washers (#24) and two Locknuts
(#26) per side. Then, slide the lower sides of L Support Tubes (#7) to the assembled tubes
(#5) together.
9. Connect the Support Tube-A (#2) to the assembled tubes (#7 and 5) by using Bolts (#21),
Washers (#24) and Locknuts (#26).
Note: Make sure all the Bolts, Washers and Locknuts go from the same directions
as shown in FIG.5.
"#11
#26
___" _ #2
#24 _
!
#21-.. _:
#7 --.
Spring Lock
_#9
5
Loading...