MD SPORTS 14801 Instructions Manual

]]]]]iii]]iii]]iii]]iii]]iii]]iii]]iii]]iii]]iii]]iii]]iii]]iii]]iiii]]iiii]]iiii]]iiii]]iiii]]iiii]]iiii]]iiii]]iiii]]iiii]]iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii]]]iiiiiiiiiiiiiiiiiiiiiiiii¸i¸i_iiiiiiii¸iiiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYIIII_DD_Y___iii__ii_

___ ASSEMBLY INSTRUCTIONS

INSTRUCClONES DE ENSAMBLAJE

@@NNNNN

MODEL #14801

LiMiTED 90 DAYS WARRANTY

This Product will be provided a limited warranty for a period of
90 Days from the date of purchase, be free of defects in parts
and workmanship.

During the limited warranty period if, in normal use, a part is

found to be defective or breaks that will be offered repair or

replacement part (at our option, either the same or an equiva-
lent model) at no additional charge. The only exceptions to the

limited warranty are such as main frames, table top, playing
surfaces, batteries, tools. The above warranties do not apply in
case of defects caused from improper usage, alteration,

misuse, abuse, accidental damage or neglect of the parts
affected.

A purchase receipt or other proof of the date of purchase will

be required before warranty service is performed. Requests for
warranty service can be provided by e-mail, send request in
writing or call our Consumer Service Department at:

Toll Free • 877-885-1635

[e-mail]

www.medalsports.com.tw

This Limited Warranty gives you specific legal rights and you

may also have other rights that vary from one state (province)

to another.

iMPORTANT NOTICE! Do Not Return This Product To The Store.

Please Keep Your Instructions! Your Model number is necessary should you need to contact us.

Please read through this instruction manual book to familiarize yourself wkh all parts and assembly
steps, kindly refer to the parts identifier below and be sure that all parts have been included.
Although we are dedicated to giving our customers the best product possible, a question may arise
or parts may be missing. If you are missing parts, or, if you have any questions, please contact our

fast and friendly service centre on: 877-885-1635

TOOLS REQUIRED:

Phillips Screwdriver- Not Included
Standard (Flat Head Screwdriver) - Not Included
Allen Wrench - Included

Electric Screwdrivers may be helpful during assembly; however, please
set a low torque and use extreme caution because screws may be high.
stripped or overtightened if the electric screwdriver's torque is set too high.

2_

ASSEMBLY TIPS:

When installing parts that have more than one bolt, hand
tighten all bolts before tightening individual bolts with a

screwdriver or allen key.
Some figures or drawings may not look exactly like your
product. Please read and understand the text before
beginning each assembly step.

WARNINGS!

READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND SAFETY

INSTRUCTIONS CAREFULLY. AT LEASTTWO ADULTS ARE NEEDED

FOR THE ASSEMBLY OF THIS TABLE.

THIS IS NOT A CHILD'S TOY. ADULT SUPERVISION IS REQUIRED

FOR CHILDREN PLAYING THIS GAME. PLEASE READ INSTRUCTIONS

CAREFULLY. PROPER USE OF THIS SET CAN AVOID DAMAGE OR

INJURY.

CHOKING HAZARD--
Table contains small parts or small balls. Not for children under 3 yrs.

2

PARTS IDENTIFIER

#1

#5

#9

#13

MAIN FRAME

1 Piece

%

GOAL

2 Pieces

ALLEN WRENCH

1 Piece

MOTOR

1 Piece

#2

#6

#10

#14

RIGHT LEG

2 Pieces

LEG BOLT

12 Pieces

ELECTRONIC SCORER

1 Piece

5/8" SCREW

2 Pieces

#3

#7

#11

LEFT LEG

2 Pieces

LEG WASHER

12 Pieces

C)

ROUND PUCK

2 Pieces

#4

#8

#12

LEG PANEL

2 Pieces

1/2" SCREW

16 Pieces

PUSHER

2 Pieces

3

Assembl Instructions

1. Open the carton of your new Air Hockey table near where you will play. Select a clear level floor.

This game requires at least two adults to assemble the table.

2. Remove all the contents from inside the carton and verify that you have all listed parts
as shown on the Parts Identifier. We suggest that you use the bottom carton as a clean flat work area
to protect the game. Carefully cut or tear the four carton corners so that the bottom is now your work
area.

3. Place the Main Frame (#1) face down on a clean and flat surface. Using the Allen Wrench (#9)
provided, attach the Right Legs (#2) and Left Legs (#3) to the main frame using the Leg Bolts (#6)

and Leg Washers (#7) as shown in FIG. 1.

4. Secure the Leg Panels (#4) to each set of legs using the Screws (#8).

2

4

3

8

3

2

6

7

4