M Design Luna 1000 DH Diamond, Luna 1150 DH Diamond, Luna 1600 DH Diamond, Luna 1300 DH Diamond, Luna 1150 CL Diamond Instructions For Installation And Use Manual

LUNA GAS DIAMOND GAS

550V-550DV-850V-850DV-1150V

02-2017

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

INSTRUCTIONS FOR INSTALLATION AND USE

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

VERY IMPORTANT

INSTALLATION INSTRUCTIONS

FOR THE M-DESIGNG GAS

FIREPLACES

THE SUPPLIER TAKES NO RESPONSBILITY FOR ANY

POSSIBLE DAMAGE, POOR WORKINGAPPLIANCES AND

ACCIDENT AS A RESULT OF INCORRECT

INSTALLATION

MAINTENANCE GAS FIREPLACE M-DESIGN

THE M-DESIGN GAS FIREPLACES MUST BE

CHECKED EVERY 2 YEARS AND GET A

MAINTENANCE. THIS IS ALSO TO MAINTAIN YOUR

WARRANTY. IF THIS WILL BE NOT

OBSERVED, THE WARRANTY FELL.

YOU CAN RELY ON M-DESIGN TO MAKE THIS CHECK

FOR YOU, OR YOU CAN DO THIS BY YOURSELF AND

FOLLOW THE METHOD BELOW.

3

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

SUMMARY

1. GENERAL REMARKS ........................................................... 5

2. CONNECTION ...................................................................... 5

3. INSTALLING THE FIREPLACE .............................................. 6

3.1.1 Positioning the fireplace ............................................... 6

3.1.2 Nearbox (Gasunit) ........................................................ 7

3.1.3 The Gas connection .................................................... 8

3.1.4 Electrical connection .................................................... 9

3.1.5 Modification natural gaz to propane ............................. 9

4. INSTALLING THE CHIMNEY ................................................ 10-13

5. FLAME ADJUSTMENT SETTINGS ........................................ 13-14

6. INSULATION AND FINISHING .............................................. 14

7. CONVECTION CURRENT ..................................................... 15-18

8. MOUNTING A 3 SIDED FRAME ............................................ 19

9. POSITIONING THE LOGS .................................................... 20-25

10. FIRST-TIME USE ................................................................ 26

11. SAFETY, ADVICE AND MAINTENANCE .............................. 26

12. GUARANTEE ...................................................................... 27

13. REMOTE CONTROL ..........................................................

28-30

14. 4-SIDED FRAME (FINISHING EXAMPLES) ......................... 31-33

15. DRAWINGS ........................................................................ 34-38

16. IDENTIFICATION BOARDS ................................................. 39-40

17. CE CERTIFICATION ............................................................ 41-43

4

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

OPEN EN CLOSE THE DOOR

For initial setup, you need to clean the window and clear the fireplace of
any dust and grease that is left behind. This is also the only maintenance
action that may be performed on the device by the user.

Thanks to a patented system, the door can be easily opened at an angle of 45° to allow a user­friendly cleaning of the window

To close, push the door gently (but not to soft) against the hooks. Make sure that all
hooks are hooked

CLOSING

OPEN

Above the glass (below the upper frame) hooks are provided (left, right and center).
Push it upwards with your fingers. the window can now be opened.

5

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

1. General remarks

This is an appliance using the closed combustion system, designed for the atmosphere
and comfort of your living-room. It constitutes an efficient source of heat and gives the
impression of a real fire.
The balanced flue appliances are based on the principle of natural extraction from the
firebox, which eliminates flue gas outside and brings in air (oxygen) from outside the
house which is necessary for combustion of the gas. It uses to this effect two concen­tric pipes. The internal pipe ensures the elimination of burned gases and the external
pipe brings in combustion air. The advantage of this principle is that the equipment
works independently of the atmosphere which predominates in the house.

2. Connection

This appliance must be connected by an approved installer in accordance with the
most recent
regulations in force. On the basis of your order specifications, this appliance is designed
for natural or propane gas.
Read the instructions before installing and using this appliance. Before installing the
appliance, please check the local regulations about this type of appliance (identification
of the type of gas, etc.) and check that the furnace is adapted to your means of instal­lationt.

It is imperative that the installer sees to the following:

•The appliance must be subject to an air tightness test of the gas and elimination of flue
gases.

•The concentric pipe, if already available, must be working correctly.

•The running of the control valve, lighting of the pilot light, the main burner and the
thermocouple must all be checked.
This appliance has been programmed and factory sealed. The sealed parts cannot be
modified. The appliance may therefore also be installed in airtight accommodation and
accommodation equipped with mechanical ventilation. It constitutes ambient heating
even in accommodation equipped with a closed ventilation system.

The appliance must be connected to the type of gas mentioned
on the appliance. Never connect a propane burner to natural gas
or vice versa!

6

A min = 3,5 cm
B = 19 cm
C min = 22.5 cm

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

3. Installing the replace

After having checked the appliance, you are ready to install your appliance. This is
done as follows

3.1.1 Positioning the appliance

Place the appliance on a stable surface using the adjustable feet. Adjust the height of
the appliance turning the bolt ( pic 1 )

The appliance must not be placed directly on the oor as
you need to allow natural convection. The appertures for the
air supply (IN) is situated underneath the appliances

Regulating the height of the appliance :
This can be made in two ways.
A regulation by 5 cm ( pic. 1 ) and a fine regulation by screw ( pic.2 ).
The minimum height as from ground to the bottom of the appliance is 3,5 cm ( A min ).
The minimum height “C min” will be 22.5 cm, measured as from the ground to 4th side
frame ( pic.3 ).
The maximum height as from the ground to the 4th side frame is 45 cm for LUNA DH and
max 35cm for Luna CL/CR/DC

pic. 1

pic. 2

Pic 3

to second burner or side burner

7

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

For safety reasons, The gasbattery or “NEARBOX” is fixed with screws at the rear of the unit
during transport .

THE UNIT CANNOT BE INSTALLED WITH THIS NEARBOX FIXED AT THE REAR, IT IS MAN­DATORY TO UNSCREW THE BATTERY FROM THE REAR PRIOR TO INSTALLATION .

unscrew 4 screws in the corners
(key 8)

gas connection1/2”

reciever
DFGT-03MC01 V09

Transmitter burner S4965C3029

Gas valva
VK4105ME5004

3.1.2 Nearbox (gasunit)

gas connection1/2”

to main burner

Electro magnet ventil 1 or 2 burners

NEARBOX FOR 1 BURNER

NEARBOX FOR 2 BURNERS

to main burner

(455 2 burners)

GAS SUPPLY TO SIDE BURNER OR SECOND
BURNER (YELLOW)

220V

NEARBOX

Connection Gas 1/2” (provide tap)

8

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

Opening provided in wall
for maintenance

Cable to ionistation pin

GAS SUPPLY TO MAIN BURNER ( RED)

flexible for GAS

True Vision is provided with
a direct ignition , no starting
pilot

3.1.3 The Gas connection

Valve 1/2”

After the “NEARBOX” has removed from the of the back of the fire, you can place it loosely on the
ground in proximity to the opening provided in the wall of mantelpiece. The device is always con­nected with an approved gas tap 1/2, and preferably with a yellow gasflexible that is reachable at all
times. Provide the mantelpiece with a door so that the valve and the electrical connection is easily
accessible.

ATTENTION : DO NOT PLACE ANY DECORATION ON THE DIRECT IGNITION PIN
(be carefull to stay out of the little rectangular zone with the dcoration)

9

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

3.1.4 Electrical connection

These appliances are equipped with a radiographic remote control, making an earthened 220V
socket necessary.
You should bear in mind that the appliance must be connected to all
electrical supplies for the purposes of service.
It’s obligatory to connect an earth current.

3.1.5 Modication natural gaz to propane

Modification of the fireplace can only be done by the manufacturer or an approved installer. A
new signal plate is provided.

10

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

Picture 1: ROOF EXIT (C31)

The concentric ue duct should not be reduced to 150/100 for all True Vision.

Picture 1

4. Installing the chimney

Install the concentric flue duct as indicated by ONTOP - METALOTERM. The only authorised pipes are
ONTOP Metaloterm™. ONTOP-METALOTERM tested our appliances with their conduct and we only
guarantee a good working of the appliance with those. Between the external wall of the pipe and the wall
or the ceiling, you should allow for a clearance of at least 50mm and protection that is suitable against
temperatures of around 130°C. The passage of the front panel cowl in the external wall must be filled in
using silicone mastic.

This is recommended with a roof exit ≥ 3m

This is recommanded with a roof exit ≤ 3 m

Ø 150/100

Appliance C (min) C (max) Postion air inlet

850V / 550V 3 m 18m 2

850DV/550DV/1150V 3 m 18m 2

Ø 200/130

Appliance C (min) C (max) Position air inlet

850V / 550V 2 m 10m 2

850DV / 550DV/1150V 2 m 9m 2

*

USDHC13 or
USDHC10

*

11

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

Picture 2: ROOF EXIT VIA EXISTING CHIMNEY (C91S)

It is obligatory to use the termination set USSAN
with positioning.

flex 130mm
or 100mm

This USSAN piece must be sealed at the
roof!

Picture 2

Tab 2

Ø 150 (min) / Ø 100

Appliance C (min) C (max) Position air inlet

850V / 550V 3 m 18m 3

850DV / 550DV / 1150V 3 m 17m 3

Ø200(min) / Ø 130

Appliance C (min) C (max) Position air inlet

850V / 550V 2 m 10m 3

850DV / 550DV / 1150V 2 m 9m 3

12

Usvk13
reduction 200/130 to 150/100

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

Picture 3: WALL EXIT (C11)

IMPORTANT: Be carefull every horizontal part does not have a negative in

clination in direction of the outlet. It is even better, when possible to
have a little inclination of 2 or 3 degrees ascending to avoid rain and
condenstation in the tube. Install wall outlet like g 1

Picture 3

Picture 4

Picture 5

Ø 150/100

With reduction usvk13 on appliance (Pic 3 )

Appliance A (min) B (min) B (max)

Position air inlet

850V
550V

1,25m
0,75m

Wall Exit A+0,5m 4

850DV
550DV

1,25m
0,75m

Wall Exit A 4

11 5 0 V 1,25m Wall Exit A 4

(A) ø 200/130 in combinatie met / combiné

avec (b) ø 150/100

With reduction usvk13 placed horizontaly after curve 90° ( Pic. 4 )

Appliance A (min)

Ø 200/130

B (min)

Ø 150/100

B (max)

Ø 150/100

Position air inlet

850V
550V

1m

0,75m

Wall Exit A+ ”USVK13” +4m 4

850DV
550DV

1m

0,75m

Wall Exit A+ ”USVK13” +3m 4

11 5 0 V 1m Wall Exit A+ ”USVK13” +3m 4

ø 200/130 (pic.5)

Appliance A (min) B (min) B (max)

Position air inlet

850V
550V

1m

0,75m

Wall Exit A+8m 3

850DV
550DV

1m

0,75m

Wall Exit A+7m 3

1150V 1m Wall Exit A+7m 3

13

1

2

3

4

Detail A

position 1 = Min
position 4 = Max

A

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

Picture 4: ROOF EXIT WITH BEND

Appliance

Ø 150/100 en/ et Ø 200/130

850V / 850DV / 1150V
550V / 550DV

for each 90° bend subtract 1m horizontally

or add 1m vertically

850V / 850DV / 1150V
550V / 550DV

for each 45°/30°/15° bend subtract 0,5m

horizontally or add 0,5 m vertically

Ø 150/100

With reduction on the appliance

Appliance A (min) B (max) C (min) (A+B+C )max Position air inlet

850V
550V

1,25 m

0,75m

A+C B-A 16 m 4

850DV
550DV

1,25 m

0,75m

(A+C) -0,5m B-A 15 m 4

1150 V 1,25 m (A+C) -0,5m B-A 15 m 4

Ø 200/130

Without reduction

Appliance A (min) B (max) C (min) (A+B+C )max Position air inlet

850V
550V

1,25 m
0,75 m

(A+C) + 7m B-A-9m 20m 4

850DV
550DV

1,25 m
0,75 m

(A+C) + 6m B-A-8m 19m 4

1150 V 1,25 m (A+C) + 6m B-A-8m 19m 4

5. Flame adjustment settings

After installing the fireplace correctly on the concentric tube or chimney system, you must make a
flame adjustment according to the draft (see pagess 9-13 with setting 1-2-3-4).

Flames settings

Caution: if the vertical part is 3 m
longer than the horizontal part, the air
inlet position lever must be set to 3

14

B

A

min. 5 mm

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

6. Insulation and nishing

Once installation is complete, the appliance can be fitted. Before doing so, check the
tightness of the gas pipe one more time. Light the appliance and check that it is wor­king: check the tightness of the gas pipe and the smoke pipe. Once you have checked
everything, you can perform the final insulating and finishing operations.
The built-in part of the appliance tends to be very warm. Please check that the ap­pliance is not too narrowly fitted and that there is adequate space for the elimination
of hot air. For insulation of the appliance, we advise you to use M Design insulating
plates. You are advised against using any other insulation product. Inflammable mate­rials as well may not be used for the finishing.

Please , follow this instruction. The appliance can overheat if you do not
follow these instructions. Errorcode F02 will appear !

Masonry must be raised around the replace. Due to the expansion
of the replace during combustion, a gap of at least 5 mm must be
provided at the front of the replace and 4 cm on each side of the
appliance. The masonry must not rest on the replace. THE FIRE­PLACE MUST BE FREE. Always leave 2 mm clearance between the
inner frame and the masonry.

A very essential point when setting up the Luna
Gold is that the distance has to be respected
inbetween fireplace and the finishing material for
the mantlepiece such as marble, gipsum,...
For this, a small bended metal sheet that is provi­ded on the fireplace ( pic.1 ) , is to be used as the
minimal reference for the distance. The finishing
can only go as far as this metal sheet (pic.2 ).
Don’t remove this ( pic.3 ) ! This allows you to
take out the 4th side frame and to let the airflow
in the mantelpiece for natural convection

Pic1

Pic2

Pic3

Air inlet

Flame setting

B

A

Adjustable air diffusion for ame setting

Air inlet

Flame setting

Adjustable air diffusion for ame setting

15

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

7. Convenction current

It is MANDATORY to equip the fireplace with a convection kit consisting of inlets and
outlets which are connected to stretchable hoses from 3m to 5m.
In this way is created a circualtion and evacuation of the heat by convection.
This is very important to avoid overheating in the firebox casing and also to distribute
the air hot air in the room or in another adjacent room (office, kitchen, ...)

This system directs the heat inside the room using hoses (150mm dia.). It is neces­sary to open minimum 2 hot air outlets. For the installation of these ducts, limit their
lengths, avoid as much as possible elbows and changes of direction, because the
losses of speed generated, decrease the efficiency of the air outlets at the end of
travel. We advise you to install the hot air grilles at the same height to have the same
heat provided. M-Design has developed hot air and ambient air outlet grilles available
from your dealer (see page 16).

Outlet grids have two or four hose connections (2/4 hoses on 1 grid!).
The air inlet grilles (not to be connected with a hose) must be placed as low as
possible at the bottom of the fireplace.

Please, follow this instructions. The appliance can overheat if you not apply
those instructions. Errorcode F02 will appear!

ATTENTION : A house is never completely 100 % dustfree, heating applian-

ces and warmth circulation create dust particles. During the periods where
you are not using the fireplace, dust is accumulated in the flexible pipe and

and the grills

This could cause a problem with a smell, so we would certainly advise you

to clear the flexible and air inlets and outlets using a vacuum cleaner regu-

larly. The smell caused by these dust particles will disappear after you have

used the fireplace again a few times. (This phenomenon is very common

and can be compared to the gray traces appearing above your radiators.)

Optionally you can order design metal lids to cover the inlets and outlets

during the summertime .

16

2xØ150

13

126

126

200

200

550

350

1223

82

64

72

268

114

44

484

82

92

92

44

115

70

82

269

281

465

2xØ150

64

13

489

82

2xØ150

13

64

82

115

44

70

269

92

92281

465

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

Design grid (outlet) with 2 connections

Inlet grid convection air 2dm

3

Inlet grid convection air 4dm²

Design gridl (outlet) with 2 connections Design grid (outlet) with 4 connections

Design grid (outlet) with 2 connections for

frontal installation (see page 17)

7. Technical data for outlet and inlet grids

17

Mirror

Masonry

Masonry

Mirror

Main
Outlet

Mirror

Masonry

Masonry

Mirror

1

2

1

82

484

82

4 81

488

DRL 2 (488x82)

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

Design grid (outlet) with 2 connections for frontal installation

18

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

You have to connect at least two appertures situated at the top of the appliance.
The appliance may not be placed directly on the floor, without the feet. This is to
allow natural convection. The appertures for the air supply are situated underneath
the aplliance. Every opening you make must be connected with a flexible tube dia
150MM
(see pic below). This will avoid the heating of the electronic part of the appliance.
In this case you will have errorcode F02.

19

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

picture 1

3 sided frame

2,5 cm

3,5 cm

4 sided frame

side frame

upper frame

picture 2

picture 3

picture 4

picture 5

picture 6

8. Mounting a 3 sided frame

Fireplace is delivered standard with 4sided frame 3,5cm, an upper and 2 sideframes ( see pic. 2 )

Before mounting the 3 sided frame, remove 4 sided frame ( lower piece ) by lift it carefully up.
Pull out the upper frame and in second way the left and right sideframes. Take the left and right
side of the 3 sided frame ( 3,5 - 7 or 10 cm ) and slide them in the notches ( see pic 4). When those
are placed in a good way, you can adjust the position to the left and to the right and from the the
front to the rear. In this way you can make the frame a good fit to the surrounding. Mount the upper
frame ( pic 5 ) and lastly the 4 sided frame ( pic 6 )

Attention : Pleas pay attention to leave approx 2 mm inbetween
the frame and the finishing material (heat=expansion)

20

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

9. Positioning the logs, diamond, sapphire and white pebbles

Put the little imitation coal pieces on the burner and here and there between the

Put the big imitation coal pieces around the burner.

Please check that the pilot light is switched off and that the appliance has cooled
down.

• Move the window to the front by pulling it. The window tips open at 45°.

• Arrange the materials supplied. In accordance with your order you will have either
a set of logs, diamond, sapphire or white pebbles. There is an adequate supply of
materials . Our appliance is approved with these materials, so please do not use
other products. Other decorative products are prohibited in our appliances. Please
do not change the delivered quantities

Attention:
Do not put anything on the ignition pin.

To arrange the logs respect the order as follows.

One bag of liite pebbles is delivred with the set. First place de little
pebbles on the burner. Place the big pebbles around the
little pebbles and be carefull to not place big pebbles directly on the
burner.

ATTENTION WHEN USING THE BIG WHITE PEBBLES

21

1

2

3

4 5

6

7

8

9

10

11

12

13

14

1

2

11

10

12

3

4

5

8

6

7

9

14

13

LUNA 850 DV

GAS

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

LUNA 850 DV

GAS

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

22

LUNA 850 V

GAS

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

23

For appliance with 2 burner in ‘stairs’

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

LUNA 550 V / 550 DV

GAS

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

24

1

2

3

4

5

6 7

8

LUNA 550 V / 550 DV

GAS

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

25

26

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

10. First-time user

The masonry and plaster surrounding a recently installed appliance holds a great deal
of moisture, which must first evaporate before commissioning the appliance. If not, the
plaster may crack or split. Ask your installer about the timescale to follow. The first time
you use it, only make a moderate-sized fire.
The first few times the appliance is used, an unpleasant odour may be apparent. It
comes from the protective paintwork. These emissions are totally harmless. To quickly
get rid of these odours, all you need to do is ventilate the room for a while.
After the first few fires, a light deposit may appear on the window. It comes from the
paintwork. Once the appliance is cold you can get rid of this deposit by using M De

-

sign’s Bio-Clean cleaning product. This product may be used later on for cleaning the
window.
The appliance must not be used if the door no longer has a window or with the door
open. If the window is broken or cracked, the appliance must not be used until the
window has been replaced. Contact your M Design reseller.

11. Safety, dvice and maintenance

Have your appliance inspected once a year by a qualified technician.

Please observe the following points:

• Closed appliances produce intense heat, which means that all the surfaces of the
external walls (metal, door frames and windows) become very hot once a certain tem

-

perature is reached. Make sure that young children do not touch the window; this
could result in severe burns.

• The logs, ceramic pebbles, a Diamond set and a Sapphire set are delivered with the
appliance. Never put other objects in the flames!

• Keep inflammable materials a suitable distance from the appliance (min. 1m)!

• Never modify the settings yourself! The furnace warranty will then be considered as
invalid, null and void.

• Never let children use the remote control without supervision.

• Always leave the pilot light on. The appliance is designed in order that the pilot light
goes out automatically every 24 hours and lights instantly. This enables the electronic
system to run down from static electricity.

• In the case where the burner goes out for any reason, wait for 3 minutes before re

-

lighting the furnace.

8

Identification board

27

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

12. Guarantee

This page is your warranty card.
The guarantee is only valid for faults caused by construction defects or defects in the
parts used to build the appliance.
M-Design offers a 12 month guarantee on all electronic parts and a 8 year guarantee on
the appliance construction.

Caution: The following items are always excluded from the guarantee:

- The glass, door, joints and internal decor.

- The defects which occur are fully or partially a consequence of

• Non respect of the order, installation and maintenance instructions

• Assembly, installation or repair by a third-party, including the buyer

• Heat cracks which normally occur in the mantel

• In cases where changes have been made to the appliance without our consent

• In cases where the buyer cannot show his/her warranty card with the purchase
invoice.
Likewise where the guarantee and/or the invoice show(s) signs of tampering or forgery
(crossed out date, illegible, modifications).
In the case you would like to make use of the manufacturer’s warranty, you should con

-

tact your reseller in the first instance. Please take good care of your purchase invoice
and warranty card and store them in a safe place.

SERIAL NUMBER

SERIAL NUMBER :

...........................................

1

2

28

1

3. Manual control (Single line burner)

From the moment the burner is on, you can start
with the flame height control.

The screen will automatically show manual
control ( flame heigt control )

Press on until you see number 15.

This is the maximum flame height.

Choose a flame height from 1 to 15

by pressing or

For all appliances, except for:
850V, 1150V, 550DV en 850DV

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

Keep pressing the button

until 24:00 appears in the top left
corner (1).
Press several times on

until you see “bnd” on the screen (2)
Press shortly on
and

You see the temperature on the
screen. Your remote control is now
connected.

2. Ignite the fire

1. First use (Connect the remote control)

Press simultaneously

on and

You hear the ionisationpen ticking.
The ticking lasts for about 15 sec.
At initial setup, it’s possible that the pilot flame
doesn’t ignite imidiatly because the pipes are not
yet fully deflated. You can try this up to 5 times
before the unit will be placed in safety. If this fails,
pleas contact your installer.

13. Remote control (direct ingnition)

29

1 2

3 4

12

3

Only for:
1150DH, 1300H-DH-CL-CR-DC,

1600H-DH-CL-CR-DC, 1900H

5. Manual control (Double line burner)

Start the first burner as in the manual control of single line burner

To light up the 2nd burner, press

First you see the wave settings (page 33). or

Press a second time and you will see a “b0” or “b0”

1 2

3 4

Remark: If after a previous use of the fireplace, you turned it off in “b1” mode,
next ignition, burner 2 lights up. If, on the other hand, you have switched off the appliance
in mode “b0” the appliance will switch on only with the burner 1

If “b0” appears, press to “b1”, burner 2 lights up.

To switch off the entire stove press

Choose a flame height from 1 to 15 by pressing or

If “b1” appaers, press to “b0” , burner 2 goes out.

1

2

1

2

Not available for:
700H, 550V, 1000RD en 1300RD

4. Manual control (Triple line burner)

Start the first burner as in the manual control of single line burner

To light up the side burners 2 and 3, press .

First you see the wave settings (page 33). or

Press a second time and you will see a “b0” or “b0”

If “b0” appears, press to “b1”, side burners 2 and 3 lights up.

If “b1” appaers, press to “b0” , side burners 2 and 3 will go out.

Choose a flame height from 1 to 15 by pressing or

To switch off the entire stove press

Remark: If after a previous use of the fireplace, you turned it off in “b1” mode,
next ignition, the burners 1,2 and 3 will light simultaneously. If, on the other hand, you have
switched off the appliance in mode “b0” the appliance will switch on only with the burner 1

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

30

: each model is standard delivered with ECO-WAVE

ECO-WAVE is an automatic cycle of fluctuating flames.

At each start-up of the fire, the system starts in ECO-WAVE mode !

6. ECO WAVE

3

1

2

Passion for re

4

Symbol that indicates that

WAVE is enabled

Press 1x short on the menu

button and “1” appears

(= Wave aan)

Press the arrow up or down.

“0” appears (=Wave off)

confirm

Press 1 x to turn off the fireplace. The fireplace will start-up with 1 or multiple burners depending on the “b” position.

Press 2x on the menu button to see whether the fire is set to “0” of “1” position.

Shut down re :

Switch off

WAV E

In case you want to go to a thermostatic control, you follow the next steps:

Press 2x the button until you see the screen with the symbols shown in picture 2.

Press or until the symbols and are blinking (pic 2).

Confirm your choise by pressing ( pic.3).

Choose a temperature with the “up” and “down” arrows (pic. 4).
Don’t place the remote control near the fire. The temperature sensor is in the remote

control. To get back to manual control do the smame until and are blinking.

Confirm with

5. Thermostatic control

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

31

35

70

105

X

Masonry

TYPE X

35mm 30

70mm 65

1105mm 100

TYPE A B C D

850 V 7 81 6 74 773 666

550 V 4 81 914 473 906

1150 V 10 81 706 1073 698

A

C

4

C

D

5

Appliance is standard delivered with lower lath 35 mm (4th side frame). The lower lath retracts 5mm
into the covering of the fireplace (see X values )

30

Masonry

the lateral lath exceeds 5 mm from
the covering of the fireplace.

lower lath

When using the 4-sided frame, see
table with X values

*

*

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

14. 4 Sided Frame - General Dimensions

32

X

min.(Y-4mm)

Min. 15cm

Min.(Y - 4mm)

2mm

Min. 16mm

5

25

Y

lower
lath 3,5cm/4mm

2mm
2mm

Masonry

Bench in natural stone

Finishing at side appliance

TYPE X Y

850 V/DV 773 666

550 V/DV 473 906

1150 V 1073 698

X = inside frame measurment (visible dimension)
Y = Measured from side down of the lower lath to side up of
the upper lath

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

14.1. Finishing with lower lath (the appliance is delivered with a lower lath of 3,5cm)

33

Connection Flexibles (2 x mandatory)

X (int.)

Y(ext.)

L

Min. 15cm

H

Y

X

2

H

L

TYPE X L Y H

850 V/DV 773 783 666 668

550 V/DV 473 483 906 908

1150 V 1073 1083 706 708

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

14.2. Finishing with 4-sided frame

Inlet convection air : MANDATORY ! ( 1 at the left andright side)

Opening to provide :
L = X + 4mm + 4mm + 2mm + 2mm
H = Y + 2mm

4-sided frame 3,5 - 7 of 10 cm

4

X = Inside measurment frame (visible dimension)
Y = Measured from side down of the lower lath
to side up of the upper lath
4 mm = thickness frame
2 mm = expansion joint

34

B

C

E

A

D

B

C

E

A

D

0 kader/cadre

frame/Rahme

3.5 cm k ader/cadre
frame/Rahme

7 cm ka der/cadre

frame/Rahme

10.5 cm kader/cad re
frame/Rahme

Luna Diamond 850 V Gas/Gaz

32

28

102

98

6

6

6

6

6

6

6

6

6

5

9

9

1

2

3

864

4

8

4

176

455

Min. 35 mm
Max. 450 mm

773 int.

Ø130

Ø200

4 x Ø150

131

1

1

9

2

0

8

6

6

6

e

x

t

.

1

3

7

1

8

8

6

5

6

in

t

.

27

32

3

3

0

786

5

67

63

6

6

6

Luna 850 V gold gas/gaz

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

15. Drawings

35

Luna 850 DV gold gas/gaz

B

D

C

H

A

B

D

C

H

A

0 kader/cadre

frame/Rahme

3.5 cm k ader/cadre
frame/Rahme

7 cm kader/cadre

frame/Rahme

10.5 cm kader/cadre
frame/Rahme

Luna Diamond 850 DV Gas/Gaz

67

63

102

98

32

28

5

468

522

662

592

27

5

32

3

6

3

786

1

0

1

6

2

3

Min. 35 mm
Max. 450 mm

909

229

458

1

6

2

6

6

6

e

x

t

.

1

8

8

5

2

2

Ø130

Ø200

164

1

2

9

2

0

0

4 x Ø150

773 int.

6

5

6

in

t

.

6

6

6

6

6

6

6

6

6

6

6

6

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

36

Luna 550 V gold gas/gaz

B

C

E

A

D

B

C

E

A

D

0 kader/cadre

frame/Rahme

3.5 cm kader/cadre
frame/Rahme

7 cm kader/cadre

frame/Rahme

10.5 cm kader/cadre
frame/Rahme

Luna Diamond 550 V Gas/Gaz

32

28

102

98

473 int.

8

9

6

in

t

.

9

0

6

e

x

t

.

32

1

2

5

2

2

3

1

5

8

1

8

8

455

176

4

8

4

Ø130

Ø200

137

3

3

0

565

Min. 35mm
Max. 450mm

3

2

9

486

27

9

0

6

9

0

6

9

0

6

5

2 x Ø150

5

67

63

9

0

6

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

37

Luna 550 DV gold gas/gaz

B

D

C

H

A

B

D

C

H

A

0 kader/cadre

frame/Rahme

3.5 cm k ader/cadre
frame/Rahme

7 cm kader/cadre

frame/Rahme

10.5 cm kader/cad re
frame/Rahme

Luna Diamond 550 DV Gas/Gaz

9

0

6

9

0

6

32

28

5

67

63

102

98

468

522

592

662

229

458

5

2

2

Ø130

Ø200

119

1

0

9

2

4

0

4 x Ø150

609

1

2

5

6

2

3

Min. 35 mm
Max. 450 mm

3

6

3

486

275

32

9

0

6

e

x

t

.

1

6

2

1

8

8

8

9

6

in

t

.

473 int.

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

38

Luna 1150 V gold gas/gaz

B

C

E

A

D

B

C

E

A

D

0 kader/cadre

frame/Rahme

3.5 cm kader/cadre
frame/Rahme

7 cm kader/cadre

frame/Rahme

10.5 cm kader/cadre
frame/Rahme

Luna Diamond 1150 V Gas/Gaz

32

28

102

98

7

0

6

7

0

6

7

0

6

5

4

8

4

Ø130

Ø200

176

455

1073 int.

6

9

6

in

t

.

7

0

6

e

x

t

.

1

3

7

1

3

8

27

32

3

3

0

1086

Min. 35 mm
Max. 450 mm

9

8

1

2

3

1165

4 x Ø150

122

150

1

2

7

1

7

5

5

7

0

6

67

63

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

39

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

16. Identication boards

40

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

41

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

17. CE Certication

42

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V

43

Instructions for installation and use DIAMOND Gas 550V-DV-850V-DV-1150V