MDB 5591 Assembly And Operation Manual

Crib + Changer Combo (5591) - Assembly and Operation Manual

Congratulations on purchasing a

MDB Family

product. This product will provide many years of service if you adhere to the following guidelines for assembly, maintenance and operation. This product is for residential use only. Any institutional use is strictly prohibited.

Please be sure to follow the instructions for proper assembly. Use a Phillips head screwdriver for assembling the crib in addition to the Allen wrench included in the hardware box. Do not use power screwdrivers. All of our products are made from natural woods. Please understand that natural woods have color variations which are the result of nature and not defects in workmanship.

DO NOT SUBSTITUTE PARTS. ALL MODELS HAVE THE SAME QUANTITY OF PARTS AND HARDWARE. YOUR MODEL MAY LOOK DIFFERENT FROM THE ONE ILLUSTRATED DUE TO STYLISTIC VARIATIONS.

WARNING!

READ ALL INSTRUCTIONS BEFORE USE OF THE CHANGING TABLE, ADD-ON CHANGING UNIT, OR CONTOURED CHANGING PAD.

!!PLEASE READ!!

Assembly of this furniture is easier with two people. Assemble furniture on debris free carpets or on the enclosed foam sheets to prevent scratching of finish. Using any power tools to assemble this furniture may potentially strip the wood. DO NOT OVERTIGHTEN SCREWS. DO NOT USE THE CHANGING TABLE IF IT IS DAMAGED OR BROKEN.

* The crib can later be converted into a toddler bed or a full-size bed. To convert to a toddler bed, turn to page 16. To convert to a full-size bed, turn to page 17.

Revised 08JUL2011

page 1

A. Back Panel

PARTS

B. Front Panel

C. Right Side Panel

H. Crib Top Panel X 2

K. Spring Frame

L. Guardrail

D. Left Side Panel

F-2. Left

Back Post

P. Drawer Back (3)

F-3. Back

Post

E. Center Panel

G-1. Right Front Post

Q. Drawer

Bottom

Board (3)

G-2. Left Front Post

F-1. Right Back Post

G-3. Front

Post

R. Dresser Back

Top Panel

M. Drawer

Front (3)

N. Right Drawer

Panel (3)

O. Left Drawer

Panel (3)

page 2

S. Dresser Back

Panel

T. Dresser Front

Top Bar

U. Dresser Center

Bar (2)

V. Dresser Middle

Bar (2)

W. Dresser Top

Bar

AA-2. Dresser

Shelf (with pre-drilled

BB. Pad

X. Dresser Bottom

Bar (2)

Y. Dresser

Center Board

AA-1. Dresser

Shelf

Z. Dresser

Top Board

HARDWARE

H1. 3 -1/2” Allen Head Bolt (8) H2. 2 -3/4” Allen Head Bolt (2)

H3. 2 -1/2” Allen Head Bolt (16) H4. 1 -3/4” Allen Head Bolt (8)

screw holes)

Tools Needed

(not included)

H5. 1” Allen

Head Bolt (4)

Phillips

screwdriver

H6. Barrel

Nut (24)

H7. 1-1/4” Wood

Screw (24) H9. 1” Metal Pin (20)

H16. Right Panel Glide (3)

H15. Knob (3)

H20. Strap

H21. Wood

Screw (2)

H17. Right Drawer Glide (3)

H24. Allen

Wrench

GUARDRAIL HARDWARE

H22. 2” Allen Head Bolt (4) H23. Lock washer (4)

H13. 1/2” Small Wood Screw for Glides (36)

H25. Lock

washer (38)

H26. Washer (4) H27. 7/8" Wood

H14. 1-1/8” Bolt

for Knob (3)

H18. Left Panel Glide (3)

H19. Left Drawer Glide (3)

Screw (2)

page 3

STEP 1. Assemble all drawers

Q. Drawer Bottom

O. Left

Drawer

Panel

M. Drawer

Front

P. Drawer Back

N. Right

Drawer

Panel

DO NOT OVERTIGHTEN.

Board

H17. Right

Drawer

Glide

H13

H19. Left

Drawer

Glide

H13

H14

H13

H15

page 4

STEP 2. Attach posts to center panel

H25

E. Center Panel

H25

G-1. Right

STE

P 3. Attach panel glides and metal pins to center and right side panel

Front Post

H25

F-1. Right Back Post

DO NOT OVERTIGHTEN.

H13

H18

H13

E. Center Panel

H13

C. Right Side Panel

H13

H16

H16. Right Panel Glide H18. Left Panel Glide

page 5

STEP 4. Attach dresser panels and

bars to right side panel

H25

C. Right Side Panel

H25

STEP 5. Attach dresser bars to

right side panel

H25

DO NOT OVERTIGHTEN.

page 6

STEP 6. Attach dresser boards

to the dresser

Z. Dresser Top Board

Y. Dresser

Center Board

STEP 7. Attach center panel to

the dresser

H25

E. Center Panel

H25

DO NOT OVERTIGHTEN.

H25

page 7

STEP 8. Attach posts to left side panel

H25

STEP 9. Attach the crib top

panel and back panel

H25

G-2. Left front post

H25

D. Left Side Panel

DO NOT OVERTIGHTEN.

H25

F-2. Left

Back Post

H25

DO NOT OVERTIGHTEN.

D. Left Side Panel

H. Crib Top Panel

H25

A. Back Panel

H25

page 8

STEP 10. Attach spring frame

Swing out four hangers at corner of the spring frame (K) carefully. Attach spring frame FLAT SIDE UP. Choose the height of the spring frame. Start at the highest level and adjust accordingly.

Bolt the spring frame (K) to legs using Allen head bolts (H5), washers (H26), lock washers (H25) and Allen wrench (H24). As the child grows, it is important to lower the spring.

Make sure the spring frame is level.

Do not overtighten.

H26

H25

Make sure the mattress support frame is installed FLAT SIDE UP. Make sure the mattress

support frame is level when installing.

*As your child grows, it is important to lower the mattress support.

K. Spring Frame

page 9

STEP 11. Attach the crib top panel and front panel

DO NOT OVERTIGHTEN.

H25

STEP 12. Place dresser shelves into the dresser

H. Crib Top Panel

B. Front Panel

H25

H27

AA-2

H27

Fix the dresser shelf (with pre-

drilled screw holes) (AA-2) using

two 7/8" wood screws (H27).

AA-1

AA-2

page 10

STEP 13. Slide drawers to the dresser

STEP 14. Attach the strap

H21

H20

H21

H20

H21

DO NOT OVERTIGHTEN.

page 11

STEP 15. Place the pad onto the changer

KEEP THIS MANUAL IN A SAFE

PLACE FOR FUTURE REFERENCE.

The recommended maximum weight of the occupant is 30 lbs on changing table.

BB. Pad

Be sure to tighten the cross bar screws now that you have installed to the stationary side. Recheck all screws and bolts to be sure they are fastened securely.

Before placing your mattress in the crib, you can make your own mattress protector by cutting the cardboard packing insert to 27” x 51”. Place it on the spring frame under the mattress to extend the life of the mattress.

CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4 INCHES (69CM)

BY 51 5/8 INCHES (131CM) WITH A THICKNESS NOT EXCEEDING 6 INCHES (15CM).

Please refer to the label (sample below) on the inside face of the headboard. Record the model/ item number and serial number of your crib, the name of the store where you made the purchase, the date of purchase and the wood the box to the lower right.

nish in

CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4 INCHES (69CM) BY 51 5/8 INCHES (131CM) WITH A THICKNESS NOT EXCEEDING 6 INCHES (15CM).

THIS PRODUCT CONFORMS TO THE APPLICABLE REGULATIONS OF THE

CONSUMER PRODUCTS SAFETY COMMISSION.

WE WILL ASK YOU FOR YOUR SERIAL NUMBER FOR ALL WARRANTY AND REPLACEMENT PART REQUESTS. PLEASE REFER TO THE LAST PAGE OF THIS INSTRUCTION SHEET FOR WARRANTY INFORMATION. KEEP THIS MANUAL FOR FUTURE REFERENCE.

SAMPLE LABEL

Please read the Caution and Warning

Statements insert before using your crib.

www.themdbfamily.com

page 12

WARNING:

Failure to follow these warnings and the assembly instructions could result in serious injury or death.

READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP THE MANUAL FOR FUTURE USE.

WARNING:

Parents should ensure a safe environment for the child by checking regularly, before placing the

child in the product, that every component is properly and securely in place.

• Do not use this crib if you cannot exactly follow the accompanying instructions. Infants can suffocate on soft bedding. Never add a pillow or comforter. Never

•

place additional padding under an infant.

To reduce the risk of SIDS, pediatricians recommend healthy infants be placed •

on their backs to sleep, unless otherwise advised by your physician.

Strings can cause strangulation! Do not place items with a string around a •

child’s neck, such as hood strings or paciﬁer cords. Do not place cords, straps, or similar items that could become wound around the child’s neck in or near this

crib. Do not suspend strings over a crib or attach strings to toys.

To help prevent strangulation tighten all fasteners. A child can trap parts of the •

body or clothing on loose fasteners.

DO NOT place a crib near a window where cords from blinds or drapes may •

strangle a child. Do not place this crib near a window or a patio door where a child could reach the cord of a blind or curtain and be strangled.

When a child is able to pull to a standing position, set the mattress to the lowest •

position and remove bumper pads, large toys and other objects that could serve as steps for climbing out.

Do not use this crib if the child is able to climb out unaided or is taller than

•

35 in. (89cm).

•

Check this product for damaged hardware, loose joints, loose bolts or other

fasteners, missing parts or sharp edges before and after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if any parts are missing, damaged or broken. DO NOT substitute parts. Contact

MDB FAMILY for replacement parts and instructional literature if needed.

DO NOT use a water mattress with this crib.• For cribs equipped with teething rails, replace teething rail if damaged, cracked •

or loose.

If reﬁnishing, use a non-toxic ﬁnish speciﬁed for children’s products.• Never use plastic shipping bags or other plastic ﬁlms as mattress covers

•

because they can cause suffocation.

Infants can suffocate in gaps between crib sides when used with a mattress •

that is too small.

• Follow warnings on all products in a crib.

• Ensure that the sides are properly latched or locked in place when the crib is

occupied.

• The mattress used with this crib should not be more than 15cm thick and

should be of such length with width that the gap between the mattress and the sides of the crib is no more than 3cm when the mattress is pushed into the corner of the crib.

WARNING:

Please do NOT remove any wood screws in the normal disassembly of the crib.

ONE YEAR LIMITED WARRANTY:

We will replace any missing parts at the time of purchase or any defective item within a one year period from the date of original purchase. Please keep your receipt so that we may process your warranty request. This warranty only covers new units with original packaging and ownership, and is not transferable. It does not cover any used, secondhand or demo models. This warranty does not cover any damaged or defective parts that result from installation and assembly, normal wear and tear, abuse, negli-

gence, improper use or alteration to the ﬁnish,

design, and hardware of the crib. The speciﬁc legal rights of this warranty may vary from state to state. Some states do not allow any exclusion or limitation of incidental damages. Some states do not allow limitation on how long an implied warranty lasts.

Storage:

Pine woods exchange moisture with the air adjust-

•

ing to major changes in room temperature and humidity. Therefore, it is best to place your furniture away from heating or air-conditioning vents. Sunlight is not friendly to solid wood furniture and

•

prolonged direct exposure to harsh sunlight can discolor the finish. Be careful not to place your furniture in direct sunlight for extended periods of time. As with all your fine furniture, blot up spills immediately.

Care and Cleaning:

Do not scratch or chip the ﬁnish. Do not use abra-

•

sive chemicals for cleaning. Clean with mild soap on a soft rag. Rinse and dry thoroughly. If you ever

reﬁnish this furniture, be sure to use only a non-toxic ﬁnish speciﬁed for children’s products. If you choose to reﬁnish this furniture, the warranty will be voided.

Registering your product is even easier than before. You can register your product on our website at : www.themdbfamily.com

IF YOU WOULD LIKE TO ORDER REPLACEMENT OR MISSING PLEASE VISIT US AT:

WWW.THEMDBFAMILY.COM

OR YOU CAN CONTACT US BY MAIL:

MDB FAMILY 855 WASHINGTON BLVD. MONTEBELLO, CA 90640

PARTS

revised05MAY2011

WARNING!

FALL HAZARD

TO PREVENT DEATH OR SERIOUS INJURY, ALWAYS KEEP CHILD WITHIN ARM’S REACH.

READ ALL INSTRUCTIONS BEFORE ASSEMBLING THIS PRODUCT. KEEP THE MANUAL FOR FUTURE USE.

ONE YEAR LIMITED WARRANTY:

WARNING:

Read all instructions before use of the changing table.•

Do not use changing table if it is damaged or broken.•

This product is not intended to be used as a changing•

table without adult supervision. Use of the product

without this may result in death or serious injury to your

child from falling. Follow all instructions on attaching

and using the changing table.

Only use the pad provided by MDB FAMILY . •

The maximum weight of the child for which the chang-•

ing table is intended is 30 lbs.

Stop using this changing table when the child is able to•

sit up or roll over.

As with all infant and baby furniture, it is important to•

check fasteners, screws, and bolts periodically for tight-

ness. Parents should ensure a safe environment for

their child by checking the furniture regularly before

placing the child in the product.

When using this product, always secure the child with•

This warranty does not cover any damaged or defective parts that result from installation and assembly, normal wear and tear, abuse, negligence, improper use or altera-

tion to the ﬁnish, design, and hardware of

the crib. The speciﬁc legal rights of this warranty may vary from state to state. Some states do not allow any exclusion or limitation of incidental damages. Some states do not allow limitation on how long an implied warranty lasts.

Registering your product is even easier than before. You can register your product on our website at : www.themdbfamily.com

IF YOU WOULD LIKE TO ORDER REPLACEMENT OR MISSING PARTS PLEASE VISIT US AT:

WWW.THEMDBFAMILY.COM

the safety strip.

WARNING!

FALL HAZARD

To prevent death or serious injury, always

keep child within arm’s

reach. Never leave child unattended and always use restraining system.

OR YOU CAN CONTACT US BY MAIL:

MDB FAMILY 855 WASHINGTON BLVD. MONTEBELLO, CA 90640

page 14

Restraint System

WARNING:

During the diaper changing process, be sure always to keep one hand on the baby to prevent the baby from falling off the changing pad. Falling from the changing pad could cause severe injury or even death to the baby.

Step 1.

Place a baby on the pad with his/her bottom on the top of the diaper. Safely secure the baby on the pad with the safety straps and buckle on the pad. This helps prevent the baby from falling off the pad, which can result in severe injury or even death of the baby.

Step 3.

Push the baby’s legs forward and create a cavity under the baby’s bottom. Clean the baby.

Step 2.

Remove the dirty diaper from the baby.

Step 4.

Reattach the new diaper to a clean and happy baby!

page 15

Crib + Changer Combo (5591)-Toddler Bed Conversion Assembly

* All of the parts and hardware you will need are supplied with the crib at the time of purchase.

STEP 1.

Unscrew the Allen head bolts and remove the front panel assembly.

STEP 3.

Attach the guardrail (L) to the front posts using four Allen head bolts (H22) and lock washer (H23). The guardrail (L) can be installed with the high end facing either to the left or the right.

Check to make sure that all of the bolts are fastened securely.

DO NOT OVERTIGHTEN.

H22H23

H23

H22

STEP 2.

Move the spring frame to the lowest level.

H23

H22

L. Guardrail

H22

H23

The mattress intended for use on the bed shall be a full-size crib mattress having

minimum dimensions of 51-5/8 in. (1310mm) in length, 27-1/4 in. (690mm) in width

and 4 in. (100mm) in thickness, or a greater thickness not exceeding 6 in (152mm).

The intended user’s minimum age must be at

least 15 months old and maximum weight must not exceed 50 lbs (22.7 kg).

WARNING :

Failure to follow these warnings and the assembly instructions could result in serious injury or death from entrapment or strangulation.

DO NOT place bed near windows where cords from blinds or drapes may strangle a child. DO NOT place

items with a string, cord, or ribbon, around a child’s neck, such as hood strings or pacifier cords. DO NOT

suspend strings over a toddler bed for any reason. If guard rails are used as the mattress containment means, guard rails provided must be used to avoid the formation of a gap between the mattress and the bed that could cause an entrapment.

page 16

Crib + Changer Combo (5591) - Full Size Conversion Assembly

* For all 4 in 1 cribs, please contact a retailer to order your full size adult wooden bed rails for your full size bed conversion.

Barrel Nut X 8 3” Phillips Head Bolt X 8

STEP 1.

Unscrew the Allen head bolts and remove the left side panel (D).

STEP 2.

Separate the dresser from the crib. Replace the posts in the center panel with front and back posts (G-3 & F-3) as illustrated.

STEP 3.

Insert barrel nuts into bed rails. Use 3” Phillips head bolts (A) to attach the rails. Tighten bolts securely with a Phillips screwdriver.

Be sure to keep the extra bolts and barrel nuts for future use.

H25

F-3

DO NOT OVERTIGHTEN.

Bed Rails

G-3

Bed Rails

page 17

MDB 5591 Assembly And Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual