Item
Models
Max Load
510 series
MH-S511
1*5A
MH-S512
2*5A
MH-S513
3*5A
MH-S511H
1*10A
www.mcohome.com User Manual
Touch Panel Switch
MH-S510 Series
Introduction
Touch Panel Switch is a wall panel built-in with Z-Wave Plus module. With its stylish design and
stable performance, the panel can be used to control house-hold electrical appliances like lamp, motor,
coffee machine, TV set etc. This product can be included and operated in any Z-Wave network with
other Z-Wave certified devices from any other manufacturers.
Specifications
Power supply: 85~260VAC, 50/60Hz
Z-Wave frequency: 908.42MHz (US), 921.4MHz (AU) or other frequency customized
Note: If an inductive load wired, please choose model MH-S511H. (LED load: <10A, inrush
current<165A/ 20ms)
Installation Instructions
IMPORTANT:
A qualified electrician with the understanding of wiring diagrams and knowledge of electrical
safety should complete the installation inside the main circuit box (normally outside your house).
Read all instructions and documentation and save for future reference.
Step1 Preparing
CAUTION: Cut off power supply at circuit breaker or fuse before installation to avoid fire, shock or
death!
Step2 Installation
Step 1: Separate the device into two parts: the
touch panel and the bottom.
Step 2: Insert all wires into the right terminals by
following the wiring diagrams as below,
and tighten screws.
Step 3: Secure the bottom part onto a junction box with screws, and then mount the touch panel back.
Step 4: Confirm the device is well mounted, power on and it is ready to operate.
1
Device Type
GENERIC_TYPE_SWITCH_BINARY
Supported command classes
COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
COMMAND_CLASS_SWITCH_BINARY
www.mcohome.com User Manual
Wiring (standard strip length: 6-8mm)
MH-S511, MH-S511H MH-S512 MH-S513
Operation
Add the device into Z-Wave network:
1. Set controller into ADD mode. Follow instructions provided by controller manufacturer.
2. Press and hold any key on the panel for 8 seconds or 3 clicks in quick succession.
Note: If the ADD is successful, all INDICATION LEDs on the panel will flash 4 times.
Remove the device from Z-Wave network:
1. Set controller into REMOVE mode. Follow instructions provided by controller manufacturer.
2. Press and hold any key on the panel for 8 seconds or 3 clicks in quick succession.
Note: If the REMOVE is successful, all INDICATION LEDs on the panel will flash 4 times. The
REMOVE will delete all association data.
Turning on/off the device:
The device can be controlled by:
Pressing any key.
Sending commands through controller or gateway.（the command classes which support this
function are Basic Command Class, Binary Command Class, and Multi Channel Command
Class.）
Multi Channel Control:
The switch can be controlled by command “MULTI_CHANNEL_ENCAP” in the command
class “COMMAND_CLASS_MULTI_CHANNEL”.
2
Byte
Name
1
COMMAND_CLASS_MULTI_CHANNEL
2
MULTI_CHANNEL_CMD_ENCAP
3
Source End Point
4
Destination End Point
5
COMMAND_CLASS_SWITCH_BASIC or COMMAND_CLASS_SWITCH_BINARY
6
BASIC_SET/BASIC_GET or BINARY_SET/BINARY_GET
7
Value ( 0xFF -- ON 0x0 -- OFF )
AG
identifier
(Root)
Max
Node
Mapped
endpoint
group
Command Classes
Trigger
situation
0x01
1
(EPs
Max
node
is
0)
all
endpoints
COMMAND_CLASS_BASIC,
BASIC_REPORT
Short press any
key for one time
all
endpoints
COMMAND_CLASS_DEVICE_RESET
_LOCALLY,
DEVICE_RESET_LOCALLY_NOTIFIC
ATION
Touch any key
20 times in
succession
all
endpoints
COMMAND_CLASS_CENTRAL_SCE
NE,
CENTRAL_SCENE_NOTIFICATION
Short press any
key for one time
0x02
5
EP1
group 2
COMMAND_CLASS_BASIC,BASIC_S
ET
Short press first
button
0x03
5
EP2
group 2
COMMAND_CLASS_BASIC,BASIC_S
ET
Short press
second button
0x04
5
EP3
group 2
COMMAND_CLASS_BASIC,BASIC_S
ET
Short press third
button
www.mcohome.com User Manual
Correspondence between key and endpoint number:
1. First key correspond to endpoint 1.
2. Second key correspond to endpoint 2.
3. Third key correspond to endpoint 3.
Multi endpoint command format:
Multi Channel Association:
3
AG
identifier
Max
Node
ID
Command Classes
Trigger situation
0x01
1
COMMAND_CLASS_BASIC, BASIC_REPORT
Short press any key for
one time
COMMAND_CLASS_DEVICE_RESET_LOCALL
Y, DEVICE_RESET_LOCALLY_NOTIFICATION
Touch any key 20 times in
succession
COMMAND_CLASS_CENTRAL_SCENE,
CENTRAL_SCENE_NOTIFICATION
Short press any key for
one time
0x02 5 COMMAND_CLASS_BASIC,BASIC_SET
Short press first button
0x03 5 COMMAND_CLASS_BASIC,BASIC_SET
Short press second button
0x04 5 COMMAND_CLASS_BASIC,BASIC_SET
Short press third button
www.mcohome.com User Manual
Root device:
1.The gateway controls the root device to open, all end points will open
2.The gateway controls the root device to close, all end points will close
3.When End Point 1 opened, it will report opening status to root device.
4.When End Point 1 closed, it will report closing status to root device.
Association:
The device supports 4 association groups (AG):
Central Scene Activate Device
As a Central Scene Activate device, it supports “Central Scene CC”. When pressing the switch
button, it will send “Central Scene Notification” to Association Group 1 (normally associated to
gateway). This function is always being activated and cannot be disabled.
ZWAVE Supported Command:
1.Root Device
Command Class supported : (supports S2 unauthenticated level)
COMMAND_CLASS_ASSOCIATION,
COMMAND_CLASS_ASSOCIATION_GRP_INFO,
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION,
COMMAND_CLASS_MULTI_CHANNEL,
COMMAND_CLASS_VERSION,
COMMAND_CLASS_MANUFACTURER_SPECIFIC,
COMMAND_CLASS_DEVICE_RESET_LOCALLY,
COMMAND_CLASS_POWERLEVEL,
COMMAND_CLASS_SWITCH_BINARY,
COMMAND_CLASS_CONFIGURATION,
COMMAND_CLASS_SCENE_ACTUATOR_CONF,
COMMAND_CLASS_SCENE_ACTIVATION,
COMMAND_CLASS_CENTRAL_SCENE,
COMMAND_CLASS_BASIC,
COMMAND_CLASS_FIRMWARE_UPDATE_MD
4
Num
ber
Function
size
description
Default
Possible values
0x02
Switch state saved or
not when power
failure
1
0x00 not saved, switch will be off when
powered again
0x01 saved, switch will keep the same
state when powered again
0x01
0-1
0x04
LED Backlit
brightness level
1
0x00 LED disabled
0x01~0x0A Min level-Max level
0x0A
0-0x0A
0x05
Key Mode
1
0x00 single click to switch on/off status
0x01 Key default as off state. When it is
turned on, then it will be turned off
automatically after a time period , which
can be set in item 0x06
0x02 Key default as on state. When it is
turned off, then it will be turned on
automatically after a time period , which
can be set in item 0x06
0x00
0-2
0x06
Key On duration
2
0x00 infinite
1~32767 unit "sec"
0x0000
0-32767
0x07
External aux-switch
type
1
0x00 Button(Momentary button)
0x01 Toggle(2-state switches)
0X00
0-1
www.mcohome.com User Manual
Command Class supported: (Not supports S2)
COMMAND_CLASS_ZWAVEPLUS_INFO,
COMMAND_CLASS_TRANSPORT_SERVICE,
COMMAND_CLASS_SECURITY,
COMMAND_CLASS_SUPERVISION
2.End Point Device
Command Class supported : (supports S2 unauthenticated level)
COMMAND_CLASS_ASSOCIATION,
COMMAND_CLASS_ASSOCIATION_GRP_INFO,
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION,
COMMAND_CLASS_SWITCH_BINARY
Command Class supported: (Not supports S2)
COMMAND_CLASS_ZWAVEPLUS_INFO,
COMMAND_CLASS_SECURITY_2,
COMMAND_CLASS_SUPERVISION
Parameters Setting:
5
www.mcohome.com User Manual
Restoring Factory Settings
Press 20 times of any button (the interval time of touching is less than 500 milliseconds and the relay
will keep same state after continually touching more than five times) or exclude the device from
Z-Wave network, the factory setting will be restored.
Please use this procedure only when the network primary controller is missing or otherwise
inoperable.
SAFETY NOTICE
1. Flush-mount only into a UL/ETL/CE certified plastic junction box and switch panel cover. The minimum size should
be 90*60*50mm, minimum Volume is 270cm3.
2. Use Copper Conductors Only.
3. CAUTION - Risk of Electric Shock - More than one disconnect switch may be required to de-energize the
equipment before servicing.
FCC Warning (Part 15.21) (USA only)
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FCC Interference Statement (Part 15.105 (b)) (USA only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
1-year Limited Warranty
We warrant this product to be free from defects in material and workmanship under normal and proper use for one year from purchase date
of the original purchaser. We will, at its option, either repair or replace any part of its products that prove defective by reason of improper
workmanship or materials. THIS LIMITED WARRANTY DOES NOT COVER ANY DAMAGE TO THIS PRODUCT THAT RESULTS
FROM IMPROPER INSTALLATION, ACCIDENT, ABUSE, MISUSE, NATURAL DISASTER, INSUFFICIENT OR EXCESSIVE
ELECTRICAL SUPPLY, ABNORMAL MECHANICAL OR ENVIRONMENTAL CONDITIONS, OR ANY UNAUTHORIZED
DISASSEMBLY, REPAIR OR MODIFICATION. This limited warranty shall not apply if: (i) the product was not used in accordance with any
accompanying instructions, or (ii) the product was not used for its intended function. This limited warranty also does not apply to any product
on which the original identification information has been altered, obliterated or removed, that has not been handled or packaged correctly, that
has been sold as second-hand or that has been resold contrary to Country and other applicable export regulations.
6
Loading...