User Manual
pg Q
CHARGER ASSY-WIRELESS QF
4CH58-AP000/010
*This product was designed for Kia Motors’ OPTIMA(QF).
*Only Qi-certified device can be charged on this product.
Thank you for purchasing this wireless vehicle charger for Kia
No Coins: Do not put the coins on this product.
Motors’ OPTIMA(QF).
Please read the user manual carefully and use the product safely.
Description of parts
Power LED
No Coins
No Smart key
QI Logo
Rubber Pad
NOTE
Qi Logo: This product is Qi-certified wireless charger.
No Smart Key: Do not put a smart key on this product.
Charge LED
H
ow to use
1. Turn on the engine, and see if the product's power LED(right) is lit.
2. Place the device that has the Qi logo on the middle of the charging
pad. (Is better to align the device to the center of the pad)
3. The Charge LED starts to light on in red as charging begins.
4. When the charging is finished, the LED will turn green.
• If it is not charging well make sure to align the device to the
center and recharge.
• Some smartphones or cases do not send the full charging signal to
wireless charger, in this case, the charge LED will remain in red.
The device is not charging
Troubleshooting
gg
D
ith
malfunction
If you encounter problems or abnormalities during the use please
- Make sure the device is qi standard.
- Relocate the device location.
- Make sure the device being charged is full.
- Make sure that something is on the wireless charger.
The charge LED is blinking fast or not lit
- Make sure you have properly connected your device with the
appropriate wireless charging case, or foreign objects are inserted
between receiver and transmitter.
- Relocate the device location.
Caution, Service
Do not put a smart key or coins on this product.
o not insert or wet w
Do not take it part or make alterations.
Keep away from any mechanical device that could be affected by a
magnetic field.
water or any other liquid.
1. Put a mobile phone in the middle of the product to charge. If the
mobile phone is placed in other position, it may cause charge
.
2. The use of original Rx Case is recommended for this equipment. If
any abnormal RX Case is used, it may cause malfunction or
damage of the equipment.
3. If there are any metal materials like coins between chargers, you
may suffer physical injuries including burns due to heat.
stop using the product and contact the store where the purchase was
made.
C
ompliance Statement
subject to the following two conditions :
gp p g
/TV
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the lim
its for a Class B digital device, pursuant to Part 15 of the FCC Rule
s. These limits are designed to provide reasonable protection agai
nst harmful interference in a residential installation. This equipmen
t generates uses and can radiate radio frequency energy and, if no
t installed and used in accordance with the instructions, may caus
e harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful inter
ference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to tr
y to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
–Consult the dealer or an experienced radio
technical for help.
C
ompliance Statement
standard(s).
()
p
IC Compliance Statement
This device complies with Industry Canada license-exempt RSS
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licen
ce standard RSS (s). L'opération est soumise aux deux conditions s
uivantes: (1) cet appareil ne peut causer d'interférences, et (2) cet
appareil doit accepter toute interférence, y compris les interférenc
es quipeuvent causer un mauvais fonctionnement de l'appareil.
User’s Caution Statement
Any changes or modifications to the equipment not expressly
approved by the party responsible for compliance could void
user’s authority to operate the equipment.
Toute changé ou modifications non expressément approuvés par
la partie responsable de la conformité pourraient
annuler l'utilisateur `autorité de faire fonctionner cet équipement.
Loading...