MCM Electronics 555-11600, 555-11605, 555-11601, 555-10606, 555-10602 Instruction Manual

...
Sound Reinforcement
Passive and Active Speaker Systems
555-11600 10" 555-11605 10" 80W RMS 555-11601 12" 555-10606 12" 120W RMS 555-10602 15" 555-10607 15" 140W RMS
Passive Models
Active Models
MCM Electronics
650 Congress Park Drive
Centerville, Ohio 45459
www.mcmelectronics.com
© 2010 MCM, a Premier Farnell Company
Safety Information
The lightning bolt within a triangle is intended to alert the user to the presence of un insulated dangerous voltage levels within the product’s enclosure.
This voltage may be of sufficient magnitude to constitute an electric shock risk.
To reduce the risk of electric
shock, do not remove cover of this device. There are no user serviceable parts inside. Refer servicing only to qualified service personnel.
The exclamation point
within a triangle is intended to alert the user to important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Safety Precautions
Read and retain these instructions
Follow all instructions and heed warnings
Do not use this device near water
If the surface becomes dirty, clean only with dry cloth, do not use solvents or
thinners
Install in accordance with the manufacturer’s instructions
Do not block ventilation openings
Do not install near heat sources such as radiators, heat registers, stoves, or other
devices that produce heat
Do not defeat the safety purpose of the grounded plug. This plug has two blades
and a third ground prong. The wide blade or third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet
Protect the power cord from being stressed at the plugs, convenience receptacles,
and where they exit the amplifier
Only use accessories specified by the manufacturer
Unplug the device during lightning storms or when unused for an extended time
Refer all servicing to qualified personnel
This device must not be exposed to water in any way. No object filled with liquids
should be placed on apparatus
These speakers are intended for stationary use on flat, level and solid surfaces. When using with speaker stands, it is the responsibility of the user to be certain the stand is capable of supporting the weight of the speaker. When used on elevated stages, whether with or without speaker stands, care should be given if placed close to the front edge of the stage, as potential risk exists for spectators in close proximity. Additionally, these are not intended for flying installations. They should not be retrofitted with flying hardware for support above stages. Ultimately, it is the sole responsibility of the user to determine safe location and placement of this or any speaker system.
Important
OVERVIEW
This versatile line of pro sound speaker systems are designed to fill a wide variety of needs including small venue sound reinforcement, stage and studio monitoring, presentation and lecture use, as a component in a larger system, or a stand alone PA. They are perfect for the traveling DJ, karaoke system, or for a permanent installation in a clubs, restaurants, houses of worship and more.
Six available models include 10", 12" and 15" sizes, in both active (amplified) and passive versions. All models feature: Durable molded ABS plastic enclosure High quality treated cone woofers Horn loaded titanium compression tweeter 1 3/8" pole mount Heavy duty integrated handles
Passive Model Features:
High power capacity
8ohm Impedance
Twist-lock (Speakon compatible) input
Daisy chain twist lock output
Rear panel twist lock connections
Active Model Features:
Rugged amplifier with 80W,
120W or 140W RMS output, depending upon model
Three input mixer, each with
independent level controls
Fixed line level output to daisy
chain a second amplified speaker
Independent controls for
master volume, bass and treble
Input #1 and #2 accept
balanced XLR and ¼" microphone signal
Input #3 accepts balanced XLR,
or two unbalanced (summed mono) line level signal
Line output is either balanced
XLR male or ¼" female
Selectable 110V / 220V
operation
Detachable IEC type line cord
EXPLANATION OF CONTROLS
1. 1/4" Microphone Input
Accepts balanced or unbalanced microphone input signal level. Level of this input is adjusted by the control immediately to the right. Ch1 and Ch2 inputs function exactly the same.
2. XLR Microphone Input
Accepts balanced or unbalanced microphone input signal level. Level of this input is adjusted by the control immediately to the right. Ch1 and Ch2 inputs function exactly the same.
3. Ch1 Level
Controls level of signal entering either 1/4" or XLR input. Ch1 and Ch2 level controls function exactly the same. Note that the 1/4" and XLR input on a single channel should not be used at the same time.
4. XLR Line Level Input
Accepts balanced or unbalanced line level input. Typical sources for this input may be an MP3, CD or DVD player, keyboard or other electronic instrument, computer sound card or mixing console output. Level of this input is adjusted by the control immediately to the right.
5. Ch3 Level
Controls level of signal entering either RCA phono or XLR input. Note that the RCA and XLR input on this channel should not be used at the same time.
6. Dual RCA Line Level Input
Accepts unbalanced line level input. Two connections are provide to accommodate common connections from consumer stereo equipment, such as tape decks, CD players, tuners and similar. Note that the two inputs are internally summed mono.
7. Master Level
Provides adjustment of the overall output level of the system.
8. Treble Control
Provides high frequency adjustment of the overall output level of the system. This control provides ±10dB adjustment of a frequency band centered at 10KHz
9. Bass Control
Provides low frequency adjustment of the overall output level of the system. This control provides ±10dB adjustment of a frequency band centered at 100Hz
10. XLR Line Level Output
Provides pre-amplified, balanced line level output, unaffected by the Master Level or Bass and Treble controls. This is ideal for driving a second amplified speaker or input on a recording device.
11. 1/4" Line Level Output
Provides pre-amplified unbalanced line level output, unaffected by the Master Level or Bass and Treble controls. This is ideal for driving a second amplified speaker or input on a recording device.
12. Input Voltage Selector
Allows selection of 110VAC or 220VAC operation. 110VAC is correct setting for use in North America, be certain the switch is in the correct position prior to use.
13. Master Power Switch
Turns power to the internal amplifier ON or OFF. "–" represents the ON position.
14. Power Fuse Access
Accepts 5mm (dia) x 20mm (L) fuse. Only replace fuse with the exact same size. With 110VAC supply voltage, correct fuse size is 555-10600 – 2.5A, 555-10601 – 4A, 555-10602 – 5A, all slow blow type.
15. Power Cord Inlet
For connection of supplied power cord. This connection accepts industry standard IEC type cords.
Specifications (Active Models)
Model Woofer
555-10600 10" 1-3/8" 80W RMS 35Hz ~ 20KHz 110 / 220 VAC 20.5" (H) x 13.5" (W) x 12.25" (D) 555-10601 12" 1-3/8" 120W RMS 30Hz~20KHz 110 / 220 VAC 24.5" (H) x 17" (W) x 13.4" (D) 555-10602 15" 1-3/8" 140W RMS 20Hz~20KHz 110 / 220 VAC 27.5" (H) x 19" (W) x 15.4" (D)
Specifications (Passive Models)
Model Woofer
555-10605 10" 1-3/8" 200W / 400W 35Hz ~ 20KHz 90dB 8 20.5" (H) x 13.5" (W) x 12.25" (D) 555-10606 12" 1-3/8" 300W / 600W 30Hz~20KHz 91dB 8 24.5" (H) x 17" (W) x 13.4" (D) 555-10607 15" 1-3/8" 350W / 700W 20Hz~20KHz 92dB 8 27.5" (H) x 19" (W) x 15.4" (D)
Compression
Tweeter Power Output Frequency Response
Compression
Tweeter
Power
Capacity
(RMS/peak)
Frequency
Response
Power
Requirements Dimensions
Sensitivity
(W/M)
Imped-
ance Dimensions
Warranty
MCM Electronics warrants to the original purchaser that these speakers will be free from defects in materials and workmanship for a period of one year. In the event that warranty replacement is required, the unit will be replaced or repaired at the sole discretion of MCM Electronics. Warranty claims must be processed through the MCM Electronics customer service department.
This warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, or improper installation. This warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted above, the purchaser’s sole remedy shall be repair or replacement as provided above. In no event will MCM Electronics be liable for any incidental or consequential damages arising from the use of this product.
MCM Custom Audio
© 2009 MCM Electronics
www.mcmelectronics.com
Loading...