McCulloch 96188000300 User Manual

MC621

Owner's Manual

MC621

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac tured to

give best possible dependability and per for mance.
Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We

have competent, well-trained tech ni cians and the proper tools to service or repair this unit.
Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower prop er ly.

Always observe the “SAFETY RULES”.

Safe Operation Practices for Walk-Behind Snow Throwers

IMPORTANT: This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury.

Look for this symbol to point out im por tant

safety precautions. It means CAUTION!!! BE­ COME ALERT!!! YOUR SAFE TY IS IN VOLVED.

WARNING: Always disconnect spark plug wire

and place it where it can not con tact plug in or­der to pre vent ac ci den tal start ing when setting
up, trans port ing, ad just ing or making re pairs.

WARNING: This snow thrower is for use on

sidewalks, driveways and other ground level
surfaces. Caution should be exercised while
using on sloping surfaces. Do not use snow
thrower on surfaces above ground level such
as roofs of residences, garages, porch es or
other such structures or buildings.

Training

1. Read, understand and follow all instructions on the
machine and in the manual(s) before operating this
unit. Be thoroughly familiar with the controls and the
proper use of the equipment. Know how to stop the
unit and disengage the controls quickly.

2. Never allow children to operate the equipment. Never
allow adults to operate the equipment without proper
instruction.

3. Keep the area of operation clear of all persons, par­ticularly small children.

4. Exercise caution to avoid slipping or falling, especially
when operating the snow thrower in reverse.

Preparation

1. Thoroughly inspect the area where the equipment is
to be used and remove all doormats, sleds, boards,
wires, and other foreign objects.

2. Disengage all clutches and shift into neutral before
starting the engine (motor) if equipped.

3. Do not operate the equipment without wearing adequate
winter garments. Avoid loose fitting clothing that can
get caught in moving parts. Wear footwear that will
improve footing on slippery surfaces.

4. Handle fuel with care; it is highly flammable
(a) Use an approved fuel container.
(b) Never add fuel to a running engine or hot engine.
(c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

WARNING: Snow throwers have ex posed

rotating parts, which can cause severe injury
from contact, or from material thrown from the
discharge chute. Keep the area of operation
clear of all persons, small children and pets at
all times including startup.

CAUTION: Muffler and other engine parts be-

come extremely hot during operation and remain
hot after engine has stopped. To avoid severe
burns on contact, stay away from these areas.

WARNING: Engine exhaust, some of its con-

stit u ents, and certain vehicle com po nents
contain or emit chem i cals known to the State
of Cal i for nia to cause can cer and birth defects
or oth er re pro duc tive harm.

(d) Never fill containers inside a vehicle or on a truck or

trailer bed with a plastic liner. Always place containers
on the ground, away from your vehicle, before filling.

(e) When practical, remove gas-powered equipment

from the truck or trailer and refuel it on the ground.
If this is not possible, then refuel such equipment
on a trailer with a portable container, rather than
from a gasoline dispenser nozzle.

(f) Keep the nozzle in contact with the rim of the fuel

tank or container opening at all times, until refueling
is complete. Do not use a nozzle lock-open device.

(g) Replace gasoline cap securely and wipe up spilled

fuel.

(h) If fuel is spilled on clothing, change clothing im-

mediately.

5. Use extension cords and receptacles as specified by
the manufacturer for all units with electric drive motors
or electric starting motors.

6. Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by manufacturer).

7. Always wear safety glasses or eye shields during op­eration or while performing an adjustment or repair to
protect eyes from foreign objects that may be thrown
from the machine.

Operation

1. Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.

2

2. Exercise extreme caution when operating on or cross­ing gravel drives, walks, or roads. Stay alert for hidden
hazards or traffic.

3. After striking a foreign object, stop the engine (motor),
disconnect the cord on electric motors, thoroughly
inspect the snow thrower for any damage, and repair
the damage before restarting and operating the snow
thrower. Remove key.

4. If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the cause.
Vibration is generally a warning of trouble.

5. Stop the engine (motor) whenever you leave the op­erating position, before unclogging the auger housing
or discharge chute, and when making any repairs,
adjustments or inspections.

6. When cleaning, repairing or inspecting the snow thrower,
stop the engine and make certain the auger blades and
all moving parts have stopped. Remove key.

7. Do not run the engine indoors, except when starting
the engine and for transporting the snow thrower in or
out of the building. Open the outside doors; exhaust
fumes are dangerous.

8. Exercise extreme caution when operating on slopes.

9. Never operate the snow thrower without proper guards,
and other safety protective devices in place and working.

10. Never direct the discharge toward people or areas
where property damage can occur. Keep children and
others away.

11. Do not overload the machine capacity by attempting
to clear snow at too fast a rate.

12. Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care when
operating in reverse.

13. Disengage power to the auger blades when snow
thrower is transported or not in use.

14. Use only attachments and accessories approved by
the manufacturer of the snow thrower.

15. Never operate the snow thrower without good visibility
or light. Always be sure of your footing, and keep a firm
hold on the handles. Walk; never run.

16. Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Maintenance and Storage

1. Check shear bolts and other bolts at frequent intervals
for proper tightness to be sure the equipment is in safe
working condition.

2. Never store the machine with fuel in the fuel tank inside
a building where ignition sources are present such as
hot water heaters, space heaters, or clothes dryers.
Allow the engine to cool before storing in any enclosure.

3. Always refer to operator’s manual for important details
if the snow thrower is to be stored for an extended
period.

4. Maintain or replace safety and instruction labels, as
necessary.

5. Run the machine a few minutes after throwing snow
to prevent freeze-up of the collector/impeller.

SERIAL NUMBER: ___________________________
DATE OF PURCHASE: _______________________
THE MODEL AND SERIAL NUMBERS WILL BE FOUND

ON A DECAL ATTACHED TO THE REAR OF THE SNOW
THROWER HOUSING (Figure 1).

YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.

PRODUCT MAINTENANCE LEVEL

MODEL

CATALOG

FOR SERVICE CALL 1-800-849-1297

ASSEMBLED IN U.S.A.
Orangeburg, SC 29118

CONFORMS TO ANSI B71.3-2005 SAFETY STANDARDS

SERIAL

407435

Figure 1

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in maintaining, caring for
and using your snow thrower.

• Follow the instructions under “Maintenance” and “Stor­ age” sec tions of this manual.

Hand contact with the rotating auger blades

inside the discharge chute is the most common
cause of injury associated with snow throwers.
Never use your hand to clean out the discharge
chute.

To clear the chute:

1. SHUT THE ENGINE OFF!

2. Wait 10 seconds to be sure the auger blades have
stopped rotating.

3. Always use a clearing tool at least 15 inches long.

PRODUCT SPECIFICATIONS

Gasoline Capacity 1.6 Quarts (1,5 Liters)
and Type: Unleaded Regular only

Oil Type SAE 30 (above 50°F)
(API SG–SL): SAE 5W-30 or 10W-30

(32° to 50°F)
SAE 5W-30 (below 32°F)

Oil Capacity: 16 Ounces (0,47 Liters)

Spark Plug: F6RTC
Gap: 0.030" (0,762 mm)

3

TABLE OF CONTENTS

SAFETY RULES ........................................................ 2-3

PRODUCT SPECIFICATIONS ...................................... 3

CUSTOMER RESPONSIBILITIES ................................ 3

SAFETY AND INSTRUCTIONAL DECALS ................. 4

SETUP........................................................................ 5-6

OPERATION ............................................................7-11

MAINTENANCE ..................................................... 11-15

STORAGE ................................................................... 16

TROUBLESHOOTING ................................................ 17

REPAIR PARTS ..................................................... 18-26

WARRANTY ................................................................ 28

KNOW YOUR SNOW THROWER

READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Com-

pare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
Save this manual for future reference.

These symbols may appear on your snow thrower or in literature supplied with the product. Learn and under­stand their meaning.

IMPORTANT: Safety and instruction decals are located near areas of potential danger. Replace damaged decals.



$!.'%2

/2ª7!2.).'

%.').%

/.

%.').%

/&&

#(/+%

02)-%2

&5%,

/),

!.$ª).3425#4)/.3ª"%&/2%ª53%ª/&ª4()3ª02/$5#4

+%%0ª4(%3%ª).3425#4)/.3ª&/2ª&5452%ª2%&%2%.#%

)'.)4)/.ª+%9

).3%24ª4/ª34!24

!.$ª25.

05,,ª/54ª4/ª34/0

2%!$ª!.$ª&/,,/7ª!,,ª3!&%49ª).&/2-!4)/.

4

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure Description Qty. Use

1.

2.

No parts required – Unfold the handle.

Carriage bolts
Flange nuts
Washers
Knob
Chute
Deflector

5
4
2
1
1
1

Install the discharge chute.
Install the discharge chute.
Install the discharge chute.
Install the discharge chute.

1. Unfolding the Handle

Procedure

1. Loosen the two handle knobs and pull out the two
handle bolts until you can move the handle freely and
rotate the handle to the operating position (Figure 2).

1

2

Figure 2

1. Handle knobs 2. Handle bolt

2. Tighten the handle knobs until they are snug (Figure 3).

2. Installing the Discharge
Chute

5 Carriage bolts
4 Flange nuts
2 Washers
1 Knob
1 Chute
1 Deflector

Procedure

Install the discharge chute as shown (Figure 4).

1

4

3

2

3

5

4

6

Figure 3

Figure 4

1. Deflector

2. Carriage bolts

3. Flange nuts

IMPORTANT: Do not overtighten the flange nuts;
otherwise you may damage the discharge chute.

5

4. Washer

5. Knob

6. Discharge chute

3. Filling the Engine with Oil

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service
classification SG–SL. Select the oil's SAE viscosity grade
according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least
once a year if the snow thrower is not used for 25 hours
in one year.

Check the crankcase oil level before starting the engine
and after each five (5) hours of continuous use. Tighten oil
fill cap / dipstick securely each time you check the oil level.

Product Overview

13

12

*11

1

2

4

3

5

6

7

8

Figure 5

NOTE: 10W30 synthetic oil is acceptable for use in cold
temperatures.

1. Move the snowthrower to a level surface.

2. Clean around the dipstick (Figure 6).
NOTE: Dipstick location may vary depending on engine

type.

3. Remove either side mounted filler cap dipstick or high
oil fill dipstick and wipe it clean.

1

Fill if oil
is below
“Add”
on the
dipstick

10

9

*11

Figure 7

1. Discharge chute

2. Chute deflector handle

3. Fuel tank cap

4. Control bar

5. Recoil start handle

6. Primer

8. Electric-start button

9. Oil drain plug

10. Drive belt cover
*11. Oil fill cap/dipstick

12. Ignition key

13. Chute deflector

7. Choke lever

* Dipstick location may vary depending on engine type.

Fill if oil is
below letter
“L” on the
ller cap

Figure 6

1. Oil filler cap/dipstick

4. Insert the dipstick into the filler neck and turn clockwise
until fully seated. Then remove the dipstick by turning
it counter-clockwise.

5. Fill oil to "FULL" on dipstick with the recommended oil.

6. Securely screw in the oil filler cap/dipstick.

6

Operation

NOTE: Determine the left and right sides of the machine

from the normal operating position.

• Gasoline is extremely flammable and explosive.
A fire or explosion from gasoline can burn you
and others.

• To prevent a static charge from igniting the gaso­line, place the container and/or snowthrower on
the ground before filling, not in a vehicle or on
an object.

• Fill the tank outdoors when the engine is cold.
Wipe up spills.

• Do not handle gasoline when smoking or around
an open flame or sparks.

• Store gasoline in an approved fuel container, out
of the reach of children.

• Do not tip the snowthrower with fuel in the fuel
tank.

The operation of any snow thrower can result
in foreign objects thrown into the eyes, which
can result in severe eye damage. Always wear
safety glasses or eye shields while operating
your snow thrower or performing any ad just-

ments or repairs. We recommend standard safe ty glasses
or a wide vision safety mask worn over spectacles.

IMPORTANT: Know how to operate all controls before
adding fuel or attempting to start the engine.

NOTE: For best results, purchase only the quantity of
gasoline that you expect to use in 30 days. Otherwise,
you may add fuel stabilizer to newly purchased gasoline
to keep it fresh for up to 6 months.

Checking the Engine Oil
Level

NOTE: 10W30 synthetic oil is acceptable for use in cold

temperatures.

1. Move the snowthrower to a level surface.

2. Clean around the dipstick (Figure 9).
NOTE: Dipstick location may vary depending on engine

type.

3. Remove either side mounted filler cap dipstick or high
oil fill dipstick and wipe it clean.

1

Fill if oil
is below
“Add”
on the
dipstick

Fill if oil is
below letter
“L” on the
ller cap

Filling the Fuel Tank

Fill the fuel tank with fresh unleaded gasoline, do not
exceed 87 octane rating (Figure 8).

Figure 8

IMPORTANT: Do not add oil to the gasoline.
IMPORTANT: Do not use E85 blended fuels. This engine

is not E20/E30/E85 compatible. Alternative fuels with
high alcohol content can cause hard starting, poor engine
performance, and may cause internal engine damage.

Figure 9

1. Oil filler cap/dipstick

4. Insert the dipstick into the filler neck and turn clockwise
until fully seated. Then remove the dipstick by turning
it counter-clockwise.

5. Fill oil to "FULL" on dipstick with the recommended oil.

6. Securely screw in the oil filler cap/dipstick.

NOTE: Running the engine with a low oil level can cause
engine damage. Always check the engine oil before start up.

NOTE: Running the engine with too much oil may cause
engine damage and excess smoke in the exhaust. Always
check the engine oil level before start up.

7

Starting the Engine

1. Push key in (Figure 10).

1

Figure 10

1. Key

2. Move choke lever to left position (Figure 11).

3. Firmly push in the primer 3 times with your thumb,
holding the primer in a for a second before releasing
it each time (Figure 12).

1

Figure 12

1. Primer

NOTE: Remove your glove when you push in the primer
so that air cannot escape from the primer hole.

IMPORTANT: Do not use the primer or the choke if the
engine has been running and is hot. Excessive priming
may flood the engine and prevent it from starting.

4. Connect an extension cord to the snowthrower and
plug the other end into a three-hole grounded 120
volt A.C. receptacle and push the electric-start button
(Figure 13), or pull the recoil start handle (Figure 14).

1. Choke lever

1

1

Figure 11

Figure 13

1. Electric start button

NOTE: Use only a UL-listed, 16-gauge extension cord
recommended for outdoor use that is not longer than 50
feet (15 m).

8

Engaging the Auger Blades

The electrical cord can become damaged, causing

a shock or fire.

Thoroughly inspect the electrical cord before plug-

ging it into a power source. If the cord is damaged,
do not use it to start the snowthrower. Replace or
repair the damaged cord immediately. Contact an
Authorized Service Dealer for assistance.

1

To engage the auger blades, hold the control bar against
the handle (Figure 15).

1

Figure 15

Figure 14

1. Recoil start handle

IMPORTANT: Run the electric starter no more than 10
times at intervals of 5 seconds on, then 5 seconds off.
Running the electric starter extensively can overheat and
damage it. If the engine does not start after this series
of attempts, wait at least 40 minutes to allow the starter
to cool before attempting to start it again. If the engine
does not start after the second series of attempts, take
the snowthrower to an Authorized Service Dealer for
service.

NOTE: If you pull the recoil handle and feel no resistance,
the starter may be frozen. Thaw out the starter before
attempting to start the snowthrower.

5. While the engine is running, move the choke lever
slowly to the right position.

6. Unplug the extension cord from the power source and
the snowthrower (Figure 13).

1. Control bar

Disengaging the Auger
Blades

To disengage the auger blades, release the control bar
(Figure 16).

1

Unplug the power cord whenever you are not start-

ing the snowthrower.

Figure 16

1. Control bar

9

Stopping the Engine

To stop the engine, pull key out (Figure 17).

Clearing a Clogged
Discharge Chute

1

1. Key
Figure 17

Adjusting the Discharge
Chute and Chute Deflector

To adjust the discharge chute, move deflector chute handle
left or right to desired position (Figure 18).

Hand contact with the rotating auger blades

inside the discharge chute is the most common
cause of injury associated with snow throwers.
Never use your hand to clean out the discharge
chute.

To clear the chute:

1. SHUT THE ENGINE OFF!

2. Wait 10 seconds to be sure the auger blades have
stopped rotating.

3. Always use a clearing tool at least 15 inches long, not
your hands (Figure 19).

1

3

2

Figure 18

1. Chute deflector knob

2. Chute deflector

3. Chute handle

To raise or lower the angle of the chute deflector, loosen
the chute deflector knob on the chute deflector and move
the chute deflector up or down (Figure 18).

Figure 19

Preventing Freeze-up after
Use

• Let the engine run for a few minutes to prevent moving
parts from freezing. Stop the engine, wait for all mov­ing parts to stop, and remove ice and snow from the
snowthrower.

• Clean off any snow and ice from the base of the chute.

• Rotate the discharge chute left and right to free it from
any ice buildup.

• With the ignition key in the Off position, pull the recoil
starter handle several times or connect the electrical
cord to a power source and the snowthrower and push
the electric start button once to prevent the recoil starter
and/or the electric starter from freezing up.

• In snowy and cold conditions, some controls and mov­ing parts may freeze. Do not use excessive force when
trying to operate frozen controls. If you have difficulty
operating any control or part, start the engine and let
it run for a few minutes.

10

Operating Tips

The auger blades can throw stones, toys, and

other foreign objects and cause serious personal
injury to the operator or to bystanders.

• Keep the area to be cleared free of all objects
that the auger blades could pick up and throw.

• Keep all children and pets away from the area
of operation.

• Do not operate snow thrower if weather condi­tions im pair visibility. Throwing snow dur ing
a heavy, windy snowstorm can blind you and
be hazardous to the safe operation of the snow
thrower.

• The best time to remove snow is the early morning.
At this time the snow is usually dry and has not been
exposed to the direct sun and warming tem per a tures.

• Slightly overlap each successive path to ensure all
snow will be removed.

• Throw snow downwind whenever possible.

• For extremely heavy snow, re duce the width of snow
removal by over lap ping previous path and moving
slowly.

• Keep engine clean and clear of snow during use. This
will help air flow and extend engine life.

• After snow-throwing is completed, allow engine to run
for a few minutes to melt snow and ice off the engine.

• Clean the entire snow thrower thoroughly after each
use and wipe dry so it is ready for next use.

Maintenance

NOTE: Determine the left and right sides of the machine from the normal operating position.

11

Adjusting the Control Cable

Checking the Control Cable

Release the control bar to remove the slack in the control
cable (Figure 20).

Adjusting the Control Cable

1. With the control bar disengaged, unhook and move
the control cable to the highest position. (Figure 21).

1

Position 2

1

Figure 20

1. Control bar

IMPORTANT: The control cable must contain some slack
when you disengage the control bar for the auger blades
to stop properly.

NOTE: You may need to adjust the control cable from
position 1 (default) to position 2 if you notice belt slip
when the control bar is engaged.

2

Position 1: Default position

(Lower Hole as shown in illustration)

Figure 21

1. Control bar

2. Adjuster link

3. Cable positions

3

Inspecting the Auger Blades

Before each session, inspect the auger blades for wear.
When a auger blade edge has worn down have an

Authorized Service Dealer replace the auger blades and
the scraper (Figure 22).

NOTE: If the control cable is adjusted to position 2,
ensure that the auger stops properly when the control bar
is released

1

2

Figure 22

1. Auger blades 2. Scraper

12

Changing the Engine Oil

Run the engine a few minutes before changing the
oil to warm it. Warm oil flows better and carries more
contaminants.

The engine oil will be hot. Avoid skin contact

with the used engine oil.

1. Move snowthrower to a level surface.

2. Run snowthrower until all fuel has been depleted.

3. Remove ignition key.

7. Clean around the oil filler cap/dipstick (Figure 24).

8. Unscrew the oil fill cap/dipstick and remove it
(Figure 24).

9. With the snowthrower in the operating position, care­fully pour oil into the oil fill hole until "Full" on the fill
cap/dipstick line (Figure 26).

Max fill: 18 oz. (0.5 l), type: automotive detergent oil with

an API service classification of SJ, SL, or higher.

Use Figure 25 below to select the best oil viscosity for

the outdoor temperature range expected:

Figure 25

1

Figure 23

1. Oil drain plug

4. Place an oil drain pan under the oil drain plug, remove
the oil drain plug, and tip the snowthrower backward and
drain the used oil in the oil drain pan (Figure 23).

5. After draining the used oil, return the snowthrower to
the operating position.

6. Install the oil drain plug and torque to 145-150 in-lbs
(17 N-m).

NOTE: Dipstick location may vary depending on engine
type.

1

Fill if oil
is below
“Add”
on the
dipstick

Fill if oil is
below letter
“L” on the
ller cap

Figure 26

NOTE: 10W30 synthetic oil is acceptable for use in cold
temperatures.

10. Screw in the oil fill cap/dipstick and hand tighten it
securely.

11. Wipe up any spilled oil.

12. Dispose of the used oil properly at a local recycling
center.

1. Oil fill cap/dipstick

1

Figure 24

13

Servicing the Spark Plug

Use a NGK BPR6ES, Champion RN9YC, or BOSCH
WR6DC spark plug or equivalent.

1. Stop the engine and wait for all moving parts to stop.

2. Rotate the discharge chute so that it faces forward.

3. Remove the discharge chute, the discharge chute
handle by removing the three carriage bolts and flange
nuts (Figure 27).

1

2

3

5. Remove the oil fill cap.

6. Remove the shroud assembly (Figure 28).

7. Install the oil fill cap.

8. Disconnect the spark plug wire from the spark plug
(Figure 29).

9. Clean around the spark plug.

10. Remove the spark plug from the cylinder head.

1

Figure 27

1. Discharge chute 2. Carriage bolts

3. Flange nuts

4. Remove the six screws that secure the shroud as­sembly (Figure 28).

1

2

3

Figure 28

1. Screw 3. Oil fill cap

2. Shroud assembly

Figure 29

1. Spark plug wire

IMPORTANT: Replace a cracked, fouled, or dirty spark
plug. Do not clean the electrodes because grit entering
the cylinder can damage the engine.

11. Set the gap on the plug to 0.030 inch (0.76 mm)
(Figure 30).

0.030 inch
(0.76 mm)

Figure 30

12. Install the spark plug and torque it to 20–22 ft-lb (27–30
N-m).

13. Connect the spark plug wire to the spark plug
(Figure 29).

14. Remove the oil fill cap.

15. Install the shroud with the screws removed in step 4
(Figure 28).

NOTE: Ensure that the shroud assembly fits together in
the side grooves.

16. Install the oil fill cap.

17. Install the discharge chute, and the discharge chute
handle onto the snowthrower using the hardware re­moved in step 3 (Figure 27).

14

Replacing the Drive Belt

If drive belt becomes worn, oil-soaked, excessively
cracked, frayed, or otherwise damaged, replace the belt.

1. Remove the drive side cover by removing the six screws
as shown in (Figure 31).

5

6

4

7

1

3

2

4. Install the new drive belt, routing it as shown in
(Figure 32).

NOTE: Route the new drive belt first around the engine
pulley, then the idler pulley, and finally around the drive
pulley while pressing down on the front of the idler arm.
(Figure 32).

5. Install the drive side cover with the screws removed in
step 1.

3

1

2

2

Figure 31

1. Drive side cover

2. Screw

3. Drive pulley

4. Idler arm

2. Press down on front of idler arm to release the belt
tension (Figure 31).

3. Remove the drive belt from the drive pulley (Figure 31).

5. Idler pulley

6. Engine pulley

7. Drive belt

4

Figure 32

1. Idler arm

2. Idler pulley

3. Engine pulley

4. Drive pulley

NOTE: Ensure that the drive belt is properly adjusted
and operating; refer to Checking the Control Cable and
Adjusting the Control Cable in the Maintenance section
of this manual.

15

Storage
Storing the Snowthrower

Immediately prepare your snow thrower for storage at
the end of the season or if the unit will not be used for 30
days or more.

WARNING: Never store the snow thrower with

gaso line in the tank in side a build ing where fumes
may reach an open flame, spark or pilot light as
on a fur nace, water heater, clothes dryer or gas
ap pli ance. Allow the engine to cool be fore storing
in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time,
clean it thor oughly, re move all dirt, grease, leaves, etc.
Store in a clean, dry area.

1. Clean entire snow thrower after each use.

2. Inspect and replace belts, if necessary (See “Replace­ing the Drive Belt” sec tion of this manual).

3. Be sure that all nuts, bolts, screws, and pins are securely
fas tened. Inspect moving parts for damage, breakage
and wear. Replace if nec es sary.

4. Touch up all rusted or chipped paint surfaces; sand
lightly before painting.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine
oil. (See “Changing the Engine Oil” section of this man ual).

CYLINDER

1. Remove spark plug.

2. Pour one ounce (29 ml) of oil through spark plug hole
into cylinder.

3. Pull recoil starter handle slowly a few times to dis trib ute
oil.

4. Replace with new spark plug.

OTHER

• Remove safety ignition key; store it in a safe place.

• Do not store gasoline from one season to another.

• Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.

• If possible, store your snow thrower indoors and cover
it to protect it from dust and dirt.

• Cover your snow thrower with a suitable pro tec tive
cover that does not retain moisture. Do not use plastic.
Plastic cannot breathe, which allows con den sa tion to
form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/
exhaust area is still warm.

FUEL SYS TEM
IMPORTANT: It is important to prevent gum deposits from

forming in essential fuel system parts such as carburetor,
fuel hose, or tank during storage. Also, alcohol blended
fuels (called gasohol or using ethanol or methanol) can
attract moisture which leads to separation and formation
of acids during storage. Acidic gas can damage the fuel
system of an engine while in storage.

• Empty the fuel tank by starting the engine and letting
it run until the fuel lines and car bu re tor are empty.

• Never use engine or carburetor cleaner prod ucts in
the fuel tank or permanent damage may occur.

• Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min i­ miz ing the formation of fuel gum deposits during stor age.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 min utes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.

16

Troubleshooting

See appropriate section in manual unless directed to an authorized service center/department.

PROBLEM CAUSE CORRECTION

Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position.

equipped) in OFF position.

2. Safety ignition key 2. Insert safety ignition key.
is not inserted.

3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline.

4. Throttle in STOP position 4. Move throttle to FAST position
(or ON/OFF switch is OFF). (or ON/OFF switch to ON position).

5. Choke in OFF position. 5. Move to FULL position.

6. Primer not depressed. 6. Prime as instructed in the Operation section of this manual.

7. Engine is flooded. 7. Wait a few minutes before restarting, DO NOT prime.

8. Spark plug wire is 8. Connect wire to spark plug.
disconnected.

9. Bad spark plug. 9. Replace spark plug.

10. Stale fuel. 10. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

11. Water in fuel. 11. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

Loss of power 1. Spark plug wire loose. 1. Reconnect spark plug wire.

2. Throwing too much snow. 2. Reduce speed and width of swath.

3. Fuel tank cap is covered 3. Remove ice and snow on and around fuel tank cap.
with ice or snow.

4. Dirty or clogged muffler. 4. Clean or replace muffler.

5. Improper cable length. 5. Adjust cable.

Engine idles or 1. Choke is in FULL position. 1. Move choke to OFF position.
runs roughly 2. Blockage in fuel line. 2. Clean fuel line.

3. Stale fuel. 3. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

4. Water in fuel. 4. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

5. Carburetor is in need of 5. Contact an authorized service center/department.
adjustment or overhaul.

Excessive 1. Loose parts or damaged 1. Tighten all fasteners. Replace damaged parts. If vibration
vibration augers or impeller. remains, contact an authorized service center/department.

Recoil starter 1. Frozen recoil starter. 1. See “IF RECOIL STARTER HAS FROZEN”
is hard to pull in the Operation section of this manual.

Loss of traction 1. Drive belt is worn. 1. Check / replace drive belt.
drive / slowing 2. Drive belt is off of pulley. 2. Check / reinstall drive belt.
of drive speed 3. Auger blades worn. 3. Contact an authorized service center/department.

Loss of snow 1. Auger belt is off of pulley. 1. Check / reinstall auger belt.
discharge or 2. Auger belt is worn. 2. Check / replace auger belt.
slowing of 3. Clogged discharge chute. 3. Clean snow chute.
snow discharge 4. Augers / impeller jammed. 4. Remove debris or foreign object from augers / impeller.

17

REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC621 (96188000300)
CHUTE ASSEMBLY

1

4

4

6

15

19

15

18

19

16

17

2

4

2

5

3

7

6

8

20

9
10

11

SSST-Chute asm_5

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

21

19

4

18

REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC621 (96188000300)
CHUTE ASSEMBLY

KEY PART
NO. NO. QTY DESCRIPTION

1 532 43 48-77 1 CHUTE.RATCHETING.PLASTIC.W/GRV
2 532 43 76-40 2 PLATE.CHUTE.RETAINER
3 532 43 76-35 1 PLATE.CHUTE.BASE
4 817 41 13-12 6 BOLT.HEX.WSH.HD.13-16 X 3/4
5 532 43 76-42 1 HANDLE.CHUTE.MS428
6 873 97 05-00 4 NUT.LOCK.HX.W/INS 5/16-18 UNC PL
7 532 43 48-79 1 SPRING.RATCHET.ARM
8 532 08 13-28 1 BOLT.SHOULDER.1/4-20 UNC X .94
9 532 43 48-78 1 ARM.CHUTE.RATCHET
10 532 13 20-04 1 HEX.NUT.1/4-20 NYLON LOCKING
11 532 43 76-26 1 PLENUM
15 532 43 73-18 5 CARRIAGE.BOLT
16 532 43 76-55 1 CHUTE
17 532 19 19-38 1 HANDLE.KNOB
18 532 43 76-43 1 DEFLECTOR.CHUTE
19 819 13 13-16 3 WASHER
20 819 13 20-16 1 WASHER.RATCHET.PAWL
21 532 42 88-67 1 BOLT

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

19

REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC621 (96188000300)
HANDLE ASSEMBLY

1

2

5

4

3

5

6

SSST-Handle asm_1

KEY PART
NO. NO. QTY DESCRIPTION

1 532 43 76-67 1 BAIL.HANDLE.PAINT.MS431
2 532 43 76-64 1 HANDLE.PNT.UPPER.SSST
3 532 43 48-06 1 CONTROL.CABLE
4 532 19 19-38 2 KNOB.HANDLE.BLACK
5 532 19 15-74 2 BOLT.HANDLE.BLACK PATCHED
6 532 14 50-06 1 CLIP.PUSH-IN.HINGED

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

20

REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC621 (96188000300)
AUGER ASSEMBLY

10

11

14

13

SSST-Auger asm_1

1

2

3

4

5

6

7

1

9

12

8

9

11

12

5

5

4

6

7

1

13

10

11

KEY PART
NO. NO. QTY DESCRIPTION

1 872 11 04-07 12 BOLT.CARRIAGE
2 532 43 76-20 1 PIN.ROLL.3/16 X 1-1/4
3 532 19 96-87 1 BOLT.1/4-20.1.50"
4 532 43 76-18 2 PLATE.CENTER.BLADE
5 532 13 20-04 13 HEX.NUT.1/4-20 NYLON LOCKING
6 819 09 10-16 8 WASHER 9/32 X 5/8 X 16 GA.
7 532 43 74-59 2 BLADE.AUGER
8 532 43 76-17 1 WELDMENT.AUGER.ASM
9 532 43 76-21 2 SUPPORT.BEARING.SSST.PNT
10 532 43 76-22 2 BEARING.BALL.MANDREL
11 817 60 04-06 4 SCREW.HEX.WASHEAD.1/4-20 X 3/8
12 872 11 04-04 2 BOLT.CARR.SS.1/4-20 UNC X 1/2.GR5
13 873 68 04-00 2 WHIZ.LOCK.NUTS.BEARING CAPS
14 812 00 00-28 1 RETAINING.CLIP

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

21

REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC621 (96188000300)
SHROUD ASSEMBLY

10

5

16

6

1

7

17

4

17

15

14

3

17

2

10

8

SSST-Shroud asm_7

9

10

12

11

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

22

REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC621 (96188000300)
SHROUD ASSEMBLY

KEY PART
NO. NO. QTY DESCRIPTION

1 532 43 76-27 1 COVER.NON-DRIVE.SIDE.MS428
2 532 43 76-30 1 COVER.DRIVE.SIDE.MS428
3 532 43 76-34 1 TOP.COVER
4 532 43 02-20 1 CAP.ASM.FUEL.2.25"FR.N/CB.E10
5 532 43 62-35 1 BULB.PRIMER
6 532 43 54-07 1 KEY HOUSING
7 532 43 76-48 1 TOP.REAR.COVER
8 532 43 76-31 1 PLATE.EXHAUST.PNT.
9 817 41 13-12 2 SCREW
10 817 67 04-12 12 SCREW.HEXWSH.THDROL.1/4-20X3/4
11 532 43 48-80 1 TANK.FUEL.ASM
12 532 14 68-48 2 TIE.CABLE.24.5X.29.NYLON.WHITE
14 532 43 54-09 2 KEY
15 532 43 48-68 3 CLIP
16 532 43 62-76 1 HANDLE.STARTER
17 532 19 66-88 4 CLIPS

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

23

REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC621 (96188000300)
FRAME ASSEMBLY

11

1

10

12

4

3

2

8

12

3

5

6

9

SSST-Frame asm_3

7

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

6

24

4

REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC621 (96188000300)
FRAME ASSEMBLY

KEY PART
NO. NO. QTY DESCRIPTION

1 532 43 48-56 1 LCT.ENGINE
2 532 43 76-06 1 FRAME.WELDMENT
3 532 43 76-62 2 WHEEL.8X1.5.BRICK.GS.3SPK.MS421
4 532 43 54-17 2 NUT.PUSH.AXLE.0.5IN
5 532 43 55-78 2 SCREW. 5/16-24 X 2.00"HHCS
6 532 15 04-06 2 BOLT.ENG. 3/8-16 X 1.280
7 532 19 17-30 3 NUT.HEX.FLANGE.1/4-20.CTR.LOCK
8 872 14 04-05 3 BOLT.RDHD.SQNK.1/4-20 UNC X 5/8
9 532 43 55-35 1 PLATE.SCRAPER
10 532 43 48-57 2 SPACER.ENGINE
11 532 43 48-74 1 LEVER.CHOKE
12 817 41 13-12 2 HEX.BOLT

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

25

REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC621 (96188000300)
DRIVE ASSEMBLY

1

7

2

8

11

12

SSST-Drive asm_3

13

10

9

KEY PART
NO. NO. QTY DESCRIPTION

1 532 43 48-60 1 SPACER.ENGINE.CRANK
2 532 43 45-02 1 KEEPER.ENGINE.BELT
3 532 42 64-90 1 PULLEY.ENG.TRACTION.3/4
4 532 85 10-74 1 WASHER.HARDEN
5 532 43 72-61 1 BELT-V.TRACTION
6 532 43 08-17 1 SCREW.CAP.SCHD.3/8-24 X 1.25
7 532 43 48-59 1 SPRING.IDLER.PULLEY.RETURN
8 532 43 76-09 1 ARM.IDLER.PNT.MS431
9 532 16 60-43 1 PULLEY.IDLER.BACKSIDE
10 817 06 06-20 1 SCREW.HXWH.THDRL.1/4-20X1-1/4
11 532 19 90-92 1 SPACER.RETAINER
12 817 06 06-20 1 SCREW.3/8-16X1.SMGML.TAP/R.BLK
13 532 43 53-83 1 PULLEY.DRIVEN

- - 532 17 45-72 1 DECAL.SPARK.CANADA

- - 532 43 64-09 1 OWNER'S.MANUAL.ENGLISH/FRENCH

3

4

5

6

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

26

SERVICE NOTES

27

LIMITED WARRANTY

The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in mate­rials and work man ship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair
or replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective
due to materials or workmanship. This Warranty is subject to the following limitations and exclusions.

1. This warranty does not apply to the engine, transaxle/transmission components, battery (except as noted below) or com­ponents parts thereof. Please refer to the applicable manufacturer's warranty on these items.

2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the pur chas­er. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser un­less such return is requested by the manufacturer.

3. Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery which we find
to be defective in manufacture, during the first ninety (90) days of ownership. After ninety (90) days, we will exchange the
Battery, charging you 1/12 of the price of a new Battery for each full month from the date of the original sale. Battery must
be maintained in accordance with the instructions furnished.

4. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of origi­nal purchase.

5. This Warranty applies only to products which have been properly assembled, adjusted, operated, and main tained in ac­ cor dance with the instructions furnished. This Warranty does not apply to any product which has been subjected to altera­tion, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product.

6. Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments, stan dard
hardware and normal maintenance.

7. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.

Should you have any unanswered questions concerning this Warranty, please contact:

HOP
Outdoor Products Customer Service Dept.
9335 Harris Corners Parkway
Charlotte, NC 28269 USA

giving the model number, serial number and date of purchase of your product and the name and address of the authorized
dealer from whom it was purchased.

THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WAR RAN­ TIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas
do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above
limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights
which vary from locale to locale.

This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.

In Canada contact:
HOP

5855 Terry Fox Way
Mississauga, Ontario
L5V 3E4

436409 08.18.10 TH Printed in the U.S.A.

28