McCue FlexCore Guardrail Instructions Manual
FlexCore Guardrail
INSTALLATION INSTRUCTIONS
Components
End Post Kit
GR-K-END
Too ls Requi red
MarkerTape
Measure
?
Questions
Mid Post Kit
GR-K-MID
Chalk
Line
Rotary
Hammer
McCue Corporation
Peabody, Massachusetts, USA
+1 (800) 800 8503
customercare@mccue.com
Core Kit
GR-K-COR
Masonry Drill Bit
5/8˝ [16mm]
1˝ [25mm]
McCue UK & Europe
Milton Keynes, United Kingdom
+44 (0)1908 365 511
uksales@mccue.com
To p Ra i l
GR-C-RAL
Corded
Drill
Lower Rail
GR-C-EXT
15/16˝ Socket
& Extension
McCue Asia
迈客(厦门)有限公司
Xiamen, Fujian, China
FlexCore Guardrail | Page 1 of 9
+86-592-2200790
7/32˝
Hex Key
mccue.com
Te mp la t e
GR-C-TMP
Drill with
7/32˝Hex Bit
Modular Product
This is a modular Guardrail System and each installation requires it's own custom layout. Please read
entire installation instructions before beginning your installation. If you require additional information,
please contact McCue Customer Care for assistance.
Template Instructions
Use the included template to accurately mark hole locations for drilling. Steps that require the template will be labeled
the template icon.
Use template
Template
for this step
Flange Hole Mark
1" [25mm] Drill Bit
6.00in
[152mm]
Center to Flange
1.50in
[38mm]
Center to Anchor
Anchor Hole Mark
5/8" [16mm] Drill Bit
Center
Anchor Hole Mark
5/8" [16mm] Drill Bit
Flange Hole Mark
1" [25mm] Drill Bit
Alignment Marks
FlexCore Guardrail | Page 2 of 9
C
e
n
t
e
r
h
o
l
e
t
o
c
e
n
t
e
r
h
ol
e
Attention: If section is less than 10' center
1
to center, see cutting instructions
120in
3048mm
Template &
+
Tape Measure
Chalk Line
+
2
TOP VIEW
!
3
Template
Use template
for this step
3.00in
[75mm]
5.5in
[140mm]
1 in
[25mm]
5/8 in
[16mm]
1" Diameter
Flange Hole
3˝ [75mm]
↓
5/8" Diameter
Anchor Hole
5.5˝ [140mm]
↓
5/8" Diameter
Anchor Hole
5.5˝ [140mm]
↓
Attention: Make sure
the barrier hole and
flange markings line
up properly
END POST TOP VIEW
MID POST TOP VIEW
1" Diameter
Flange Hole
3˝ [75mm]
↓
5/8" Diameter
Anchor Hole
5.5˝ [140mm]
↓
5/8" Diameter
Anchor Hole
5.5˝ [140mm]
↓
1" Diameter
Flange Hole
3˝ [75mm]
↓
Rotar y Hamm er
+
with 1˝ & 5/8˝ Drill Bits
FlexCore Guardrail | Page 3 of 9
4
Impact Driver
+
with 15/16˝ Socket
5/8 Anchor
Washer
5
6
Damper
Core
Flange
7
Aluminum Pin
7/32˝
+
Hex Key
!
Attention:
Start thread by
hand. Do not
cross thread!
Drill Optional.
FlexCore Guardrail | Page 4 of 9
8
End Post:
Go to step 14
Mid Post:
Continue to next step
9
!
Attention: If rails are not
at the desired length, see
cutting instructions
Use template
for this step
Template
Template &
+
Tape Measure
120in
3048mm
FlexCore Guardrail | Page 5 of 9
Loading...