McAfee NTBA T-200, NTBA T-500 Quick Start Manual
NTBA Appliance T-200 and T-500 Quick Start Guide
McAfee Network Security Platform
1 Install the mounting rails
Position the mounting rails correctly and install them at same levels.
At the front of the rack, position one of the mounting rails so that its mounting bracket aligns with the
a
required rack holes. Clip the rail into the rack.
Revision B
Figure 1 Slide rail installation
At the back of the rack, pull the back mounting-bracket (extending the mounting rail) so that it aligns with
b
the required rack holes.
Clip the rail to the rack and secure it.
c
Repeat these steps to secure the second mounting rail to the rack.
d
Make sure that the mounting rails are at the same level on each side of the rack.
e
Make sure that you follow the safety warnings. When identifying where you want the NTBA
Appliance to go in the rack, remember that you should always load the rack from the bottom
up. If you are installing multiple NTBA Appliances, start with the lowest available position rst.
1
Install the NTBA Appliance in the mounting rails
With help from another person, lift the NTBA Appliance so that the side rails at the back of the NTBA
1
Appliance are aligned with the mounting rails in the rack, then push the NTBA Appliance into the
mounting rails until it stops.
Lifting the NTBA Appliance and attaching it to the rack is a two-person job.
Use a screwdriver to x a screw through the front and back rack holes to secure the system to the rack.
2
Attach the provided cable management arm if required.
3
Attach the lockable bezel to protect the front panel if required.
4
2 Front panel features and indicators T-500 and T-200
The front panel features and indicators of NTBA Appliance T-500 and T-200 are as follows:
Figure 2 Front panel — T-500 and T-200
Item Description
1 Hard drives
2 Optical drive
3 Power-on indicator (on the Mini Control Panel)
4 System identication indicator light (on the Mini Control Panel)
5 USB connector (on the Mini Control Panel)
2
3 Back panel features and indicators T-500
The back panel features and indicators of NTBA Appliance T-500 are as follows:
Figure 3 Back panel — T-500
Item Description
1 System identication indicator light
2 Console port
3 Video connector
4 USB ports (4)
5 Management port
6 Remote management module NIC
7 Collection ports (2-copper)
8 Power supply 1
9 Power supply 2
10 Collection ports (2-ber)
11 Power supply 1 status indicator light
12 Power supply 2 status indicator light
4 Back panel features and indicators—T-200
The back panel features and indicators of NTBA Appliance T-200 are as follows:
Figure 4 T-200 back panel
Item Description
1 System identication indicator light
2 Console port
3
Item Description
3 Video connector
4 USB ports (4)
5 Management port
6 Remote management module NIC
7 Collection ports (4-copper)
8 Power supply 1 status indicator light
9 Power supply 1
10 Power supply 2 status indicator light
11 Power supply 2
5 Hardware specications
Table 1 Hardware specications
Appliance model T-200 T-500
Form factor 1U 1U
Width 16.9" (430 mm) 16.9" (430 mm)
Depth 27.19" (690.6 mm) 27.19" (690.6 mm)
Height 1.69" (43 mm) 1.69" (43 mm)
Maximum weight 17.2 kg (38.1 lbs) 17.2 kg (38.1 lbs)
Redundant power supply 650W 650W
Quiescent power utilization 170W 225W
Estimated inlet power utilization (worst case scenario) 426W 544W
6 NTBA Appliance - technical specications
Table 2 NTBA Appliance technical specications
Parameter Limits
Dimensions
• Height - 43.2 mm 1.70 in • Depth without CMA - 665.5
• Width without rails - 430.0
mm 16.93 in
• Width with rails - 470.0 mm
18.50 in
mm 26.2 in
• Depth with CMA - 812.8 mm
32.00 in
Operating Temperature +10°C to +35°C with the maximum rate of change not to exceed 10°C per
Non- Operating Temperature -40°C to +70°C
4
hour
Loading...