M&C MP Series, MP12, MP06 Instruction Manual
Analytical Diaphragm Pump Series MP
®
MP06, MP12
Instruction Manual
Version 1.00.02
2 MP06, MP12 | 1.00.02 www.mc-techgroup.com
Dear customer,
Thank you for buying our product. In this manual you will find all necessary information about this M&C
product. The information in the manual is fast and easy to find, so you can start using your M&C product
right after you have read the manual.
If you have any question regarding the product or the application, please don’t hesitate to contact M&C
or your M&C authorized distributor. You will find all the addresses in the appendix of this instruction
manual.
For additional information about our products, please go to M&C’s website www.mc-techgroup.com.
There you can find the data sheets and manuals of our products in German and English.
This Operating Manual does not claim completeness and may be subject
to technical modifications.
© 10/2018 M&C TechGroup Germany GmbH. Reproduction of this document or its content is not allowed without permission from M&C.
MP® is a registered trade mark.
Version: 1.00.02
www.mc-techgroup.com MP06, MP12 | 1.00.02 3
List of Contents
1 General information .................................................................................................................... 4
2 Declaration of conformity ........................................................................................................... 4
3 Safety instructions...................................................................................................................... 5
4 Warranty ...................................................................................................................................... 5
5 Used terms and signal indications ............................................................................................ 6
6 Introduction ................................ ................................................................................................ . 8
7 Description .................................................................................................................................. 8
7.1 Ambient conditions .................................................................................................................... 9
7.2 Safety ................................ ........................................................................................................ 9
8 Technical data ........................................................................................................................... 10
9 Receipt of goods and storage .................................................................................................. 10
10 Installation instructions ........................................................................................................... 10
10.1 Mechanical installation ............................................................................................................ 11
10.2 Electrical installation ................................................................................................................ 11
10.3 Pneumatic installation ................................................................ ............................................. 12
11 Supply line connections ........................................................................................................... 12
11.1 Hose-/tube connections ........................................................................................................... 12
12 Starting ...................................................................................................................................... 13
13 Closing down ............................................................................................................................ 14
14 Maintenance .............................................................................................................................. 14
14.1 Changing the diaphragm, valves and sealings ........................................................................ 15
14.2 Cleaning .................................................................................................................................. 16
15 Trouble shooting ...................................................................................................................... 17
16 Spare part list ............................................................................................................................ 18
17 Appendix ................................................................................................................................... 18
List of Figures
Figure 1 Performance characteristics MP06/12 .............................................................................. 8
Figure 2 Dimensions (mm) MP06/12 ........................................................................................... 11
Figure 3 Pump head with hexagon screws ................................................................................... 15
Figure 4 Dismounted pump head ................................................................................................. 15
4 MP06, MP12 | 1.00.02 www.mc-techgroup.com
Head Office
M&C TechGroup Germany GmbH Rehhecke 79 40885 Ratingen Germany
Telephone: 02102 / 935 - 0
Fax: 02102 / 935 - 111
E - mail: info@mc-techgroup.com
www.mc-techgroup.com
1 GENERAL INFORMATION
The product described in this instruction manual has been built and tested in our production facility.
All M&C products are packed to be shipped safely. To ensure the safe operation and to maintain the
safe condition, all instructions and regulations stated in this instruction manual need to be followed. This
instruction manual includes all information regarding proper transportation, storage, installation, operation and maintenance of this product by qualified personnel.
Follow all instructions and warnings closely.
Read this manual carefully before commissioning and operating the device. If you have any questions
regarding the product or the application, please don’t hesitate to contact M&C or your M&C authorized
distributor.
2 DECLARATION OF CONFORMITY
CE - Certification
The product described in this operating manual complies with the following EU directives:
EMC-Instruction
The requirements of the EU directive 2014/30/EU “Electromagnetic compatibility“ are met.
Low Voltage Directive
The requirement of the EU directive 2014/35/EU “Low Voltage Directive“ are met.
The compliance with this EU directive has been examined according to DIN EN 61010.
Declaration of conformity
The EU Declaration of conformity can be downloaded from the M&C homepage or directly requested
from M&C.
www.mc-techgroup.com MP06, MP12 | 1.00.02 5
3 SAFETY INSTRUCTIONS
Follow these basic safety procedures when mounting, starting up or operating this equipment:
Read this operating manual before starting up and use of the equipment. The information and warnings
given in this operating manual must be heeded.
Any work on electrical equipment is only to be carried out by trained specialists as per the regulations
currently in force.
Attention must be paid to the requirements of VDE 0100 (IEC 364) when setting high-power electrical
units with nominal voltages of up to 1000 V, together with the associated standards and stipulations.
Check the details on the type plate to ensure that the equipment is connected to the correct mains
voltage.
Protection against touching dangerously high electrical voltages:
Before opening the equipment, it must be switched off and hold no voltages. This also applies to any
external control circuits that are connected.
The device is only to be used within the permitted range of temperatures and pressures.
Check that the location is weather-protected. It should not be subject to either direct rain or moisture.
The device must not be used in hazardous areas.
Installation, maintenance, monitoring and any repairs may only be done by authorized personnel with
respect to the relevant stipulations.
4 WARRANTY
In case of a device failure, please contact immediately M&C or your M&C authorized distributor.
We have a warranty period of 12 months from the delivery date. The warranty covers only appropriately
used products and does not cover the consumable parts. Please find the complete warranty conditions
in our terms and conditions.
The warranty includes a free-of-charge repair in our production facility or the free replacement of the
device. If you return a device to M&C, please be sure that it is properly packaged and shipped with
protective packaging. The repaired or replaced device will be shipped free of delivery charges to the
point of use.
6 MP06, MP12 | 1.00.02 www.mc-techgroup.com
5 USED TERMS AND SIGNAL INDICATIONS
DANGER!
This means that death, severe physical injuries and/or important material damages will occur in case the respective safety measures are
not fulfilled.
W ARNING!
This means that death, severe physical injuries and/or important material damages may occur in case the respective safety measures
are not fulfilled.
CAUTION!
This means that minor physical injuries may occur in case the respective safety measures are not fulfilled.
CAUT I O N !
Without the warning triangle means that a material damage may occur
in case the respective safety measures are not met.
ATTE N T I O N !
This means that an unintentional situation or an unintentional status
may occur in case the respective note is not respected.
NOTE!
These are important information about the product or parts of the operating manual which require user’s attention.
QUALIFIED PERSONNEL
These are persons with necessary qualification who are familiar with
installation, use and maintenance of the product.
High voltages!
Protect yourself and others against damages which might be caused
by high voltages.
Corrosive!
These substances destroy living tissue and equipment upon contact.
Do not breathe vapors; avoid contact with skin and eyes.
Wear protective gloves!
Working with chemicals, sharpe objects or extremly high temperatures requires wearing protective gloves.
Wear safety glasses!
Protect your eyes while working with chemicals or sharpe objects.
Wear safety glasses to avoid getting something in your eyes.
Loading...