MBT Lighting LZ500 User Manual

1
LZ500 Green Laser User Manual
Thanks for purchasing LZ500 Green Laser.
and operation instruction. Keep this manual in order to consult it in the future.
The quality of every set of the products is guaranteed in the factory before the shipment. Please
check the accessories as the packing list inside. If the carton appears to be damaged, please inspect
the fixture carefully. In case damage has been found or some parts are missing, please contact
Neo-Laser after service department before shipping back the product.
Safety Information
1. Always ground the fixture electrically properly.
2. For indoor use only. Keep in cool and dry place with the ambient temperature of 10-35℃. Put the
fixture in steady place and do not shake.
3. Continuous operation of over 4 hours will shorten the life of the laser. Please always keep within
4 hours.
4. The lens at the aperture will be covered with dirt and dust that will decrease the power output.
Please clean it with the soft cloths or paper periodically.
5. Do not attempt to tear off the warranty paper. Such action will avoid the company’s warranty.
6. Do not attempt to dismantle the fixture if problems happen. Please connect with Neo-Laser after
service department directly.
7. Do not throw away the packing material. If problems happen, please pack the product with the
material and send back to Neo-Laser after service department
Fuse Replacement
Note: replace the fuse with the same specified. If not, the potential damage will be avoided of the
company’s responsibility.
Replace the fuseDisconnect the power, use the screwdriver to unscrew the fuse holder, take out
the fuse, place it with the good one of the same specified and finally screw the fuse tight.
Technical Specification:
1 AC PowerAC 110 V/ 220V , 50~60 HZ , Fuse(2A)
2 Laser Wavelength 532nm, Verdure, Facula Sizeф12, Power 10mW
3 Control system: high capacity macro processor 4 Scanner: step motor , X/Y scanning. 5 Display ModeDMX/ Sound Active/ Auto
2
6 Laser Safety LevelClass IIIB
7 Connector3-pin DMX Connector / XLR
8 Net Weight KG
9 Size 280MM*206MM*163MM (L x W x H)
Function Introduction:
1. SOUND ACTIVE
The laser graphic is controlled by with the sound, that is the graphic effect changes with the rhythm.
Turning the sensitivity knob in a clockwise direction will increase the sound sensitivity. Turning the
sensitivity knob in a counter-clockwise direction will decrease the sound sensitivity. Only the medium and
low frequency that reaches certain sound intensity can control the changing effect of the graphic. Without
sound activation for 7 seconds, the system shuts out the laser.
2. AUTO
The laser graphics runs automatically by the built-in programs. Via Auto mode, the laser cannot be shut
off automatically.
3. DMX control
The system only accepts the DMX 512 control. DMX control can control the laser’s on/off, the graphics,
and its size, color, direction, scan speed, and display speed etc.
Function Settings:
4 Work Mode:
1. SOUND_ACTIVE —— triggered by sound only
2. AUTO_MODE—— default program, not subject to change with the external effect
3. SLAVE——controlled by Master only, receive Master’s data
Note: only one master, no link with console
4. DMX MODE——controlled by DMX 512 console only, receive console’s data
Set the system function with the dipswitch.
See the function listed below.
1. The dipswitches 10, 11 and 12 are for the setting of the system function.
The dipswitches 1-9 are for the setting of the DMX Channel Address in DMX mode. If not in DMX
mode, the dipswitches 1-9 can be set randomly.
2. The setting of the projector’s address is needed via DMX mode. Under control of DMX 512 console,
the projector takes up 9 channels.
Dip Switch Setting 0=OFF 1=ON X=OFF or ON
3
DMX
ADDRES
S
MATHEM
ATICAL
RIDDLE:
ADDR
CH_NUM × N + 1
CH_NUMDMX CHANNEL OF THIS PROJECTORCH_NUM>=9
N: PROJECTOR CHANNEL NUMBERN=0,1,2,3……
EG:Each projector is distributed with 16 DMX channels
Loop1 ADDR1 Loop2 ADDR17
Loop3 ADDR33 Loop4 ADDR49
Address Setting:
In binary system, there are only two number. 0 meaning "OFF" and 1 meaning "on". The numbers
increase by multiplying the previous value by 2. Positions from dipswitch 1 to dip switch 9 signify binary
value from lower to high position.
EG LOOP ADDR BINARY
1 1 100000000
2 17 100010000
3 33 100001000
DMX control table:
Note: via
DMX, only
CH3 & 4
are valid in
Auto &
Sound
Active
Mode.
Genera
l
Operation:
DIPSWITCH CHART
FUNCTION
1 2 3 4 5 6 7 8 9
10
11
12
X X X X X X X X X 0 0
0
SOUND
ACTIVE
X X X X X X X X X 0 0
1
AUTO
MODE
SET DMX ADDRESS
0 1 0
DMX
MODE
X X X X X X X X X 0 1 1 SLAVE
Channel
Function
DMX Value
Detail
CH1
Mode Selection
0~30
Laser Off
31~100
DMX
101~175
Auto
176~255
Sound Active
CH2
Pattern Selection
0~255
35 patterns
CH3
X Position
0~255
Pan
CH4
Y Position
0~255
Tilt
CH5
Scan Size
0~255
Size from small to
big
CH6
Scan Speed
0~255
Speed from fast
to slow
4
1. Mode settings: Based on different application, different modes are set. If in DMX mode, bear in
mind the correct DMX address assignment.
2. Connection: connect the projector and DMX 512 console with the DMX signal cable. As for Stand
Alone, there is no need.
3. Powered on, laser emits the beam in 2 seconds.
4. The projector can be controlled to play and edit shows by DMX512 console in DMX mode, by
default program in auto mode, and in sound active mode if sound sensitivity knob is kept in proper
position
M/S mode:
1. Stand Alone——Via MASTER_ SOUND or MASTER_ AUTO, no console is needed. Laser shows
only obey sound or default program.
2. Mode settings: set the dipswitch in corresponding position, that is
MASTER_ SOUND:#100,#110, 120
MASTER_ AUTO 100,#110, 121
SLAVE: 100,#111,#121
3. Connection: Use XLR- XLR cable to connect the Master’s DMX output with the DMX Input of the
first Slave, and then output of the first Slave with input of second Slave till all the Slaves are
connected in this way.
4. Powered on, laser emits the beam in 2 seconds
5.The projector can be controlled to play shows by default program in Auto mode, and in MASTER_
SOUND mode if sound sensitivity knob is kept in proper position
Note:
1. Via Master/Slave mode, there should be only one Master and no DMX512 controller.
2. Power on the Master and the Slaves at the same time or first power on the Slaves, then the
Master.
N. SLAVE 2.SLAVE 1. MASTER( Sound/Auto )
MASTER /SLAVE Connection
DMX Mode:
1. Use standard DMX512 console in DMX Mode.
2. Mode settings: set the dipswitch in corresponding position, that is DMX Mode:#100,#11
1, 120.
3. Connection: Use XLR-XLR cable to connect DMX 512 console with the DMX Input of first
projector, and then output of the first projector with input of second projector till all the projectors
are connected in this way.
5
4. Powered on, laser emits the beam in 2 seconds
5. Console control
N. DMX 2.DMX 1. DMX
DMX Connection
Accessories:
1.User Manual 1PCS
2. Handle 1PCS
3.DMXcable 1PCS
4. Power cable 1PCS
Trouble Shooting:
Problems
Reasons
Remedy
Power indicator off
and no laser
Check if AC power matches
specified
Make sure of the specified power or
check the power facility
Via stand alone mode:
power indicator on, no
laser
Set to Slave mode by mistake
Set to Stand-alone mode
(Stand-alone Sound Active or
Stand-alone Auto)
Via M/S mode,
Slave projector works
abnormally
1. The mode setting (only one
Master with others set as
Slave)
2. Check if there is DMX console
or not
3. Check the connection between
Master and Slaves
1.Set the work mode properly
2.Disconnect with the DMX signal
3.Make sure of the connection
between Master and Slaves
Via DMX mode, DMX
indicator off and no
laser
1. Check if the work mode is set
to DMX mode .
2. Check the XLR-XLR cable’s
connection and quality
3. Set the work mode to DMX
mode properly
4. Make sure of the XLR-XLR
cable’s connection and quality
Via DMX mode, DMX
indicator flicker,
but out of control of the
console.
Make sure the DMX console’s
channel distribution match with the
laser’s
Set the console’s channel
distribution and the laser’s DMX
address again.
Some patterns are
blocked
—————
Power on again and the system
regain normality
6
Any other problems, please contact your distributor or service Dept. of "Neo-Laser".
DMX Address Quick Reference Chart
Dip Switch Position
DMX DIP SWITCH SET
0=OFF
1=ON
X=OFF or ON
#9 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
#8 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
#7 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
#6 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
#1
#2
#3
#4
#5 0 0 0 0 0
32
64
96
128
160
192
224
256
288
320
352
384
416
448
480 1 0 0 0
0 1
33
65
97
129
161
193
225
257
289
321
353
385
417
449
481 0 1 0 0 0 2
34
66
98
130
162
194
226
258
290
322
354
386
418
450
482 1 1 0 0 0 3
35
67
99
131
163
195
227
259
291
323
355
387
419
451
483 0 0 1 0 0 4
36
68
100
132
164
196
228
260
292
324
356
388
420
452
484 1 0 1 0 0 5
37
69
101
133
165
197
229
261
293
325
357
389
421
453
485 0 1 1 0 0 6
38
70
102
134
166
198
230
262
294
326
358
390
422
454
486 1 1 1 0 0 7
39
71
103
135
167
199
231
263
295
327
359
391
423
455
487 0 0 0 1 0 8
40
72
104
136
168
200
232
264
296
328
360
392
424
456
488 1 0 0 1 0 9
41
73
105
137
169
201
233
265
297
329
361
393
425
457
489 0 1 0 1 0 10
42
74
106
138
170
202
234
266
298
330
362
394
426
458
490 1 1 0 1 0 11
43
75
107
139
171
203
235
267
299
331
363
395
427
459
491 0 0 1 1 0 12
44
76
108
140
172
204
236
268
300
332
364
396
428
460
492 1 0 1 1 0 13
45
77
109
141
173
205
237
269
301
333
365
397
429
461
493 0 1 1 1 0 14
46
78
110
142
174
206
238
270
302
334
366
398
430
462
494 1 1 1 1 0 15
47
79
111
143
175
207
239
271
303
335
367
399
431
463
495 0 0 0 0 1 16
48
80
112
144
176
208
240
272
304
336
368
400
432
464
496 1 0 0 0 1 17
49
81
113
145
177
209
241
273
305
337
369
401
433
465
497 0 1 0 0 1 18
50
82
114
146
178
210
242
274
306
338
370
402
434
466
498 1 1 0 0 1 19
51
83
115
147
179
211
243
275
307
339
371
403
435
467
499 0 0 1 0 1 20
52
84
116
148
180
212
244
276
308
340
372
404
436
468
500 1 0 1 0 1
21
53
85
117
149
181
213
245
277
309
341
373
405
437
469
501 0 1 1 0
1 22
54
86
118
150
182
214
246
278
310
342
374
406
438
470
502 1 1 1 0 1 23
55
87
119
151
183
215
247
279
311
343
375
407
439
471
503 0 0 0 1 1 24
56
88
120
152
184
216
248
280
312
344
376
408
440
472
504 1 0 0 1 1 25
57
89
121
153
185
217
249
281
313
345
377
409
441
473
505 0 1 0 1 1 26
58
90
122
154
186
218
250
282
314
346
378
410
442
474
506 1 1 0 1 1 27
59
91
123
155
187
219
251
283
315
347
379
411
443
475
507 0 0 1 1 1 28
60
92
124
156
188
220
252
284
316
348
380
412
444
476
508 1 0 1 1 1 29
61
93
125
157
189
221
253
285
317
349
381
413
445
477
509 0 1 1 1 1 30
62
94
126
158
190
222
254
286
318
350
382
414
446
478
510 1 1 1 1 1
31
63
95
127
159
191
223
255
287
319
351
383
415
447
479
511
Dip Switch Position DMX Address
Loading...