User
User
User
User Manual
Manual
Manual
Manual
L
EDKANDYBARUV
L
EDKANDYBARUV
L
L EDKANDYBARUV
EDKANDYBARUV
Unpacking: Thank you for purchasing the LEDKANDYBARUV.
Every LEDKANDYBARUV has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred
during shipping. If the carton appears to be damaged ,
carefully inspect your fixture for any damage and be sure all
equipment necessary to operate the unit has arrived intact. In
the event damage has been found or parts are missing, please
contact our toll free customer support number for further
instructions. Please do not return this unit to your dealer without
contacting customer support first.
Introduction:
fixture can operate in three different operating modes ;
DMX contorl,sound-active, or in a Master/Slave configuration.
The LEDKANDYBARUV comes with several built in programs
that can be used , while operating as a dimmer unit or when
used in multiples linked in a master/slave configuration. For
best results use fog or special effects smoke to enhance the
beams projections.
The LEDKANDYBARUV is a three channel. The
Warning! To prevent or reduce the risk of electrical hock or fire,
do not expose this unit to rain or moisture.
Warning!
directly into the light source at all times!
This may cause severe eye damage. Avoid looking
DMX Value and Function
Model: LEDKANDYBARUV
Voltage: 100V~120V/60Hz or 220V~240V/50Hz
LED : 192 x 10mm Purple LED
Power Consumption: 20W
Fuse : 1Amp
Weight: 4.3Kgs.
Dimensions : 965 x 64 x 153mm
Colors : Purple Color Mixing
DMX Channels : 3 DMX Channel Modes
Features of L
• Color Strobe Effect
• LED Chases (Adjustable Speeds)
• Electronic Dimming 0-100%
• Built in Microphone
• DMX-512 protocol
• 3 DMX Modes
• 3 Operating Modes - Sound Active, Show Mode, or DMX Control
• DMX-512 Protocol Compatible (three DMX Channels)
• 3 Operating Modes - Master/Slave; dmx-control; Sound Active
• Digital Display for Address and Function Setting
EDKANDYBARUV
On-Board System Menu. The LEDKANDYBARUV comes with
an easy to navigate system menu. This next section will detail the
functions of each command in the system menu. Please read the
next section thoroughly!
To access the main menu press the ESC button. Tap the UP or
DOWN buttons until you reach function you wish to change. When
you reach the function you wish to change press the ENTER
button. When a function is selected use the UP or Down buttons to
change the function settings. Once your changes are made press
the ENTER button,
1
0
0
A
d
d
r
A
2
1
5
A
1
t
u
A
o
t
u
A
2
t
u
A
0
0
0
C
L
o
o
C
5
2
5
C
1
u
o
S
u
d
o
S
o
S
3
u
A
L
S
v
A
L
S
r
e
V
will be displayed,SP00 is no strobing,SP01~SP09 is purple strobing from
slow to fast.
Soud - This menu will let you select your desired sound mode
1. Tap the MENU button until “Soun” is displayed, press ENTER.
2. “Soux” will now be displayed, You can confirm three modes by UP or
DOWN for sound mode.
SLav- This menu will let you select your desired Master/slave mode
11
S
S
S
S
P
P
p
p
Addr - DMX Address Setting via control
board and moter sstting
1. Tap the ESC button and UP button or
DOWN button until “Addr” is displayed,
press ENTER.
2. “Axxx” will now be displayed, “x”
1
represents the displayed address. Press
the UP or DOWN buttons to find your
desired address.
9
Auto - This menu will let you select your
desired auto mode
0
0
1. Tap the ESC button and UP button or
DOWN button until “Auto” is displayed,
press ENTER.
2. “Autx” will now be displayed, You can
9
0
confirm three modes by UP or DOWN for
auto mode.
Colo - This menu will let you select either
a static colour
Tap the ESC button and UP button
1.
or DOWN button until “CoLo” is
displayed, press ENTER.
2.Either “CoL X”, “X” representing a
number between 1-9 or “AtF ” will be
displayed. Press the UP or DOWN buttons
to select either a static color. If you select a
static color press ENTER and SP00~SP09
1.Tap the MENU button until “SLav” is displayed, press ENTER.
2. “Slav ” will now be displayed,Slave mode is confirmed. It will be slaved by
auto mode, sound mode and chase mode.
VER - This will display the software version
1. Tap the MENU button until “VER” is displayed. Press the ENTER button
and the software vesion will be displayed.
2. Press the MENU button to leave this function.
DMX control mode
This function will allow you to control each individual fixtures traits with a
standard DMX-512 controller such as the Elation Show Designer.
Universal DMX Control: This function allows you to use a universal
DMX-512 controller such as the Elation DMX Operator or Elation Show
Designer to control head movement, A DMX controller allows you to create
unique programs tailored to your individual needs.
1. The LEDKANDYBARUV uses three DMX channel modes.See next
page for detailed description of the DMX traits.
2. This will allow you to create your own programes.
Loading...