User
User
User
User Manual
Manual
Manual
Manual
L
ED4EYES
L
ED4EYES
L
L ED4EYES
ED4EYES
144 …… 151 program 18
152 …… 159 program 19
160 …… 167 program 20
168 …… 175 program 21
176 …… 183 program 22
184 …… 191 program 23
192 …… 199 program 24
200 …… 207 program 25
208 …… 215 program 26
216 …… 223 program 27
224 …… 231 program 28
232 …… 239 program 29
240 …… 247 sound 1
248 …… 255 sound 2
ch2 0 …… 255 speed(slow to fast)
ch3
LEDs (100,000 hr. rating)
• 3 DMX Channels
• 4-Button LED DMX Display
• 3 operation modes: DMX, Sound Active & Master/Slave
• Beam angle: 50 degrees
• Power Consumption: 20W
• Multi-voltage Operation: AC 120V, 60Hz
• Dimensions (LxWxH): 312 x 306 x 334 mm
• N.W: 5 kgs.
• N.W: 6 kgs.
0 …… 7 no flash
8 …… 255 flash(slow to fast)
Model:
LED4EYES
Light Source:
·
128pcs* 5mm
super bright
LEDs( 32red
24green 24 blue
24white 24yellow)
• Extreme long
lifetime of the
Unpacking: Thank you for purchasing the LED4EYES. Every
LED4EYES has been thoroughly tested and has been shipped
in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your
fixture for any damage and be sure all equipment necessary
to operate the unit has arrived intact. In the event damage has
been found or parts are missing , please contact our toll free
customer support number for further instructions. Please do
not return this unit to your dealer without contacting customer
support first.
Introduction: The LED4EYES is a three channel, The fixture
can operate in three different operating modes ; DMX
contorl, sound-active, or in a Master/Slave configuration. For
best results use fog or special effect s smoke to enhance the
beams projections.
Warning! To prevent or reduce the risk of electrical hock or fire, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking
directly into the light source at all times!
Features of LED4EYES
• Color Strobe Effect
• LED Chases (Adjustable Speeds)
• Built in Microphone
• DMX-512 protocol
• 3 Operating Modes - Sound Active, Show Mode, or DMX
Control
• DMX-512 Protocol Compatible
• 3 Operating Modes - Master/Slave; dmx-control; Sound Active
• Digital Display for Address and Function Setting
• RGBWA,five colors make charming effect.
On-Board System Menu. The LED4EYES comes with an easy
to navigate system menu. This next section will detail the functions
of each command in the system menu. Please read the next
section thoroughly!
To access the main menu press the ESC button. Tap the UP or
DOWN buttons until you reach function you wish to change. When
you reach the function you wish to change press the ENTER button.
When a function is selected use the UP or Down buttons to change
the function settings. Once your changes are made press the
ENTER button,
Addr - DMX
Address Setting via
control board and
moter setting
Tap the ESC button
and UP button or
DOWN button until
“Addr” is displayed,
press ENTER.
“Axxx” will now be
displayed, “x”
represents the
displayed address.
Press the UP or
DOWN buttons to
find your desired
address.
Auto - This menu will let you select your desired auto mode
Tap the ESC button and UP button or DOWN button until “Auto” is
displayed, press ENTER. Aut ” will now be displayed, now auto
mode is running. Then tip the ENTER, “F xx” id displayed, Press
the UP or DOWN buttons to set the flash speed ,please the ENTER,
speed of flash is set and “S xx” is displayed , Press the UP or
DOWN buttons to set the run speed , please the ENTER, speed of
runi is set and “t xx” is displayed , Press the UP or DOWN buttons
to set the run times for mode ,
soun - This menu will let you select your desired sound mode
Tap the MENU button until “Soud” is displayed, press ENTER.
“Soux” will now be displayed, You can confirm three modes by UP
or DOWN for sound sensitiveness. Then tip the ENTER, “F xx” id
displayed, Press the UP or DOWN buttons to set the flash
speed ,please the ENTER, speed of flash is set and “S xx” is
displayed , Press the UP or DOWN buttons to set the run speed ,
please the ENTER, speed of runi is set and “t xx” is displayed ,
Press the UP or DOWN buttons to set the run times for mode ,
SLav- This menu will let you select your desired Master/slave
mode
1.Press the MENU button until “SLav” is displayed, press ENTER.
2. “Sla ” will now be displayed.
VER - This will display the software version
Tap the MENU button until “VER” is displayed.
Press the MENU button to leave this function
DMX control mode
This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation Show
Designer.
Universal DMX Control: This function allows you to use a universal DMX-512 controller such as the Elation DMX Operator or
Elation Show Designer to control head movement, A DMX
controller allows you to create unique programs tailored to your
individual needs.
DMX channels and value
channels dmx value fuction
ch1
0 …… 7 nop
8 …… 15 program 1
16 …… 23 program 2
24 …… 31 program 3
32 …… 39 program 4
40 …… 47 program 5
48 …… 55 program 6
56 …… 63 program 7
64 …… 71 program 8
72 …… 79 program 9
80 …… 87 program 10
88 …… 95 program 11
96 …… 103 program 12
104 …… 111 program 13
112 …… 119 program 14
120 …… 127 program 15
128 …… 135 program 16
136 …… 143 program 17
Loading...