MB QUART MYKRO Amplifiers User Manual

MYKRO
Installation Manual
Congratulations! By purchasing an amplifier from MB Quart, you have decided on a product of the highest technical quality. MB Quart wishes you great enjoyment with your amplifier. Should you have any questions about this system or other MB Quart products, please email us at info@maxxsonics.com
System Design
The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please remember that any system is only as good as its weakest link. Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion.
Lower power amplifiers will clip earlier than their more powerful cousins, and cause loudspeaker failure when overdriven, due to the harmonics generated by a clipped signal, thus overheating voice coils.
Amplifiers should be mounted with the fins running horizontally for best convection cooling, to minimize overheating. Purchase the best quality RCA cables you can afford, for reliability and less engine noise interference in the audio system.
It is highly recommended that the amplifier be mounted to a board of MDF or other solid structure using the 4 mounting screws provided. Avoid mounting the amplifier to metal as this can introduce noise and other unwanted issues. When mounting the amplifier, ensure that it is mounted HORIZONTALLY, as shown in the diagram above, for optimal heat dissipation. Mounting amplifiers to speaker enclosures is not recommended as this can cause damage to the amplifier components. When choosing a location for mounting the amplifier, ensure that you check for clearance from wires, gas tank, electrical devices and brake lines etc.
WOOD
RM440.4 / RM740.5 / RM1000.1
Index
WARRANTY
INSTALLATION INSTRUCTIONS
General Instructions
Settings for Best Performance
TROUBLE SHOOTING
RM440.4 4-Channel Amplifiers
RM740.5 5-Channel Amplifiers
RM1000.1 1-Channel Amplifier
TECHNICAL DATA
WARRANTY
1
2
3
4
5
6
7
9
1
FOR EXTENDED WARRANTY INFORMATION, PLEASE VISIT
WWW.MAXXWARRANTY.COM
1
INSTALLATION INSTRUCTIONS
General Instructions
General:
Run the wiring so that RCA cables are at least 18“ away from power and speaker cables. Keep RCA cables away from electrical devices in the vehicle that can cause electrical noise, such as electric fuel pumps, emission control modules and other on-board electronic modules.
Power and ground connections:(See table below) Use a sufficient gauge power cable and ground cable using the chart below as reference to what size wire you require. Mykro series amplifiers require at least 4 gauge power wire. In a multi amplifier system, add the total value of the manufacture recommended fusing to get your total system amperage. Some applications may require multiple runs of power wire to meet the system requirements. In multi amplifier systems it is advisable to mount a large enough fuse right at the battery, and run one or multiple +12 volt power cables to a fused distribution block near the amplifiers. It is then a simple matter to connect the +12 volt terminal of each amplifier to the distribution block. During this process, please ensure that the main power fuse is removed to avoid shorting the electrical system. The main fuse must be within 12” of the vehicles battery.
Ground each amplifier with as short a ground lead as possible directly to the vehicle chassis using at least 4 gauge wire or equivalent to the size of the amplifiers’ power wire. Use a ground distribution block, if you wish, but it is extremely important to keep the main ground lead from this distribution block to the chassis as short as possible , not more than 12“. The ground connection integrity to the chassis is very important, and the best way to achieve a good, solid electrical and mechanical contact is to use a large round crimp lug, crimped and soldered to the ground cable. The next step is to scrape the paint off the vehicle chassis , slightly larger than the ground lug, at the connection point. Drill a clearance hole in the chassis, the same size as the lug hole, and use a bolt, spring washer and nut to securely fasten the ground lug. Use petroleum jelly to coat the bolt/lug connection, to prevent oxidization with time.
TIP: Use the same approach when installing head units, equalizers or any audio equipment for that matter - run short individual grounds from each piece directly to the vehicle chassis, to minimize ground loops and system noise. All power, ground and speaker connections should be crimped and soldered for reliability. Make sure that none of the cable insulation can chafe against exposed metal in the vehicle, causing short circuits to the chassis.
Safe connection sequence: After all cables are run, connect speaker wires to the speakers and amplifiers, then run and plug in RCA cables. Next, connect all power, ground, and remote turn on leads. Now connect all +12 volt cables to the amplifier/s and distribution blocks and fuse holders. Finally, connect the main +12 volt cable to the battery, with the main fuse removed, and we are almost ready to power up the system.
Power up the system:
The following procedure may seem like overkill, but there is nothing more frustrating when turning on a system for the first time, and it does not work properly immediately. First, make sure the head unit is off, and turn all level controls to minimum (counterclockwise), including the head unit volume control. Set all equalizers to 0 dB (no boost), and all crossover frequency controls at approximate frequencies, as recommended by the loudspeaker manufacturer. Set all input selector and crossover switches as required for the application. Remove all amplifier fuses, and insert the main fuse at the battery. If the fuse does not blow, you can insert the fuse in one of the amplifiers, and we are ready to turn on the system. Turn the head unit on, insert a CD, or select a radio station, and increase the head unit volume control. If the system sounds fine, turn off the head unit, and install fuses in the remaining amplifiers, one by one, till the complete system is powered up and functioning properly.
WIRE LENGTH
SYSTEM AMPERAGE
35-50
7-10 ft. 10-13 ft. 13-16 ft.
8
6
4
16-19 ft. 19-22 ft. 22-28 ft.
4
4
4
WIRE GAUGE
50-65
68-85
85-105
105-125
125-150
6
4
4
4
2
4
4
2
2
0
4
2
2
0
0
4
2
2
0
0
4
2
2
0
0
2
0
0
0
0
2
INSTALLATION INSTRUCTIONS
Settings for Best Performance
RM440.4 / RM740.5 General:
At this point you are ready to get more specific on the settings for your amplifier.
High Pass:
-When in Hi Pass operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o’clock position is a great starting point. EXAMPLE: If you adjust the High Pass to 100Hz, the amplifier will not play frequencies below 100Hz but will play frequencies from 100Hz to the highest frequency the amplifier is capable of reproducing.
-When in Low Pass/Bandpass operation, this setting acts as a low frequency cut off for your system reproduction aka Subsonic Filter. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o’clock position is a great starting point. EXAMPLE: If you adjust the High Pass to 60Hz, the amplifier will not play frequencies below 60Hz but will play frequencies from 60Hz to the chosen Low Pass frequency.
-When in Flat/Full operation, the Low Pass crossover is bypassed.
Bass EQ:
This setting is a fixed bass boost at 45Hz that is variable from 0-12dB. This feature provides impact to your bass, but if not adjusted correctly, it can be over used and cause damage to your speakers and amplifiers. It is best to slowly turn this setting clockwise until the desired punch is felt. It is not recommended to exceed the 12 o’clock position unless listening at a low volume or a low recording quality as this can result in high distortion and possibly clipping.
Low Pass:
The Low Pass control acts as a ceiling and doesn’t allow frequencies to the right of the desired setting to be reproduced. Turning the potentiometer all the way to the right is a great starting point. EXAMPLE: If you adjust the Low Pass to 120Hz, the amplifier will not play frequencies above 120Hz but will play frequencies from 120Hz to the chosen Hi Pass or Subsonic frequency.
-When in Hi Pass operation, this setting is bypassed.
Level Control Setup:
Ensure that the Level is turned completely to the left prior to turning the system on. Next you should insert a CD or cassette that you are familiar with to use as a reference, and turn the head unit volume control to about 80% of its full setting. The system sound level will of course be very low, and the following procedures will help you to match the amplifier input sensitivities properly to the head unit output signal level. It is important to match the amplifier LEVEL input sensitivity to the Radio/CD output sensitivity. This can be located in the Radio/CD manual. If the Radio/CD output sensitivity is 2 volts, then adjust the amplifier LEVEL input to 2 volts.
If you are not sure what the Radio output sensitivity is, follow these general guide lines: Turn the level control up slowly, till you hear distortion, then back off a few degrees on the control. If at any point your amplifier goes into protection, you will need to turn the Level to the left a bit and then try again. If you reach a point where the output does not increase, stop turning the Level control to the right as the amplifier/speaker combo has reached its maxx output in this application.
RM1000.1
General:
At this point you are ready to get more specific on the settings for your amplifier.
Subsonic:
This setting acts as a low frequency cut off for your system bass reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o’clock position is a great starting point. EXAMPLE: If you adjust the Subsonic to 25Hz, the amplifier will not play frequencies below 25Hz but will play frequencies from 25Hz to the chosen Low Pass frequency.
Bass EQ:
This setting is a fixed bass boost at 45Hz that is variable from 0-10dB. This feature provides impact to your bass, but if not adjusted correctly, it can be over used and cause damage to your subwoofers and amplifiers. It is best to slowly turn this setting clockwise until the desired punch is felt. It is not recommended to exceed the 12 o’clock position unless listening at a low volume or a low recording quality as this can result in high distortion and possibly clipping.
Low Pass:
The Low Pass control acts as a ceiling and doesn’t allow frequencies to the right of the desired setting to be reproduced. The 12 o’clock position is a great starting point. EXAMPLE: If you adjust the Low Pass to 80Hz, the amplifier will not play frequencies above 80Hz but will play frequencies from 80Hz to the chosen Subsonic frequency.
Level Control Setup:
Ensure that the Level is turned completely to the left prior to turning the system on. Next you should insert a CD or cassette that you are familiar with to use as a reference, and turn the head unit volume control to about 80% of its full setting. The system sound level will of course be very low, and the following procedures will help you to match the amplifier input sensitivities properly to the head unit output signal level. It is important to match the amplifier LEVEL input sensitivity to the Radio/CD output sensitivity. This can be located in the Radio/CD manual. If the Radio/CD output sensitivity is 2 volts, then adjust the amplifier LEVEL input to 2 volts.
If you are not sure what the Radio output sensitivity is, follow these general guide lines: Turn the level control up slowly, till you hear distortion, then back off a few degrees on the control. If at any point your amplifier goes into protection, you will need to turn the Level to the left a bit and then try again. If you reach a point where the output does not increase, stop turning the Level control to the right as the amplifier/subwoofer combo has reached its maxx output in this application.
3
TROUBLE SHOOTING
The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault.
Description of the Diagnostic system built into all MB Quart amplifiers
The diagnostic system will shut down the amplifier, until reset by turning the head unit off, and back on. This state of affairs will be indicated by the front panel PROTECT LED lighting up under the following conditions: 1 - A short circuit on the loudspeaker leads. 2 - An internal amplifier fault that causes a DC offset on the loudspeaker output.
Should the amplifier go into diagnostic mode, simply disconnect all RCA and speaker leads, while keeping +12 volt, power ground and remote leads connected.
1. Now turn the amplifier back on, and if the diagnostic LED lights, the amplifier has an internal fault.
2. If not, plug the RCA cables back, and reset the amplifier. If it goes into diagnostic now, the fault lies in the input, either with bad cables or source unit.
3. If the amplifier seems fine with RCA cables plugged in, connect the speakers, one at a time, and if one of the speakers or its wiring is faulty, it will activate the diagnostic system.
Amplifier heatsink overheating
The amplifiers will shut down when the heatsink temperature reaches 80 degrees centigrade, and turn back on once the unit has cooled down below that point.
Causes of overheating:
1 - Inadequate cooling - relocate or remount to provide better natural airflow over the fins. 2 - Driving high power levels into low impedances - back off on the volume control, and/or make sure you are not loading the amplifier with less than the recommended loudspeaker impedance.
Low output power
1 - Check that level controls have been set up properly. 2 - Make sure that the battery voltage, as measured at the amplifier’s +12 volt and ground terminals, is 11 volts or more. 3 - Check all +12 volt and ground connections.
Fuses blowing
1 - The use of loudspeaker impedances below the recommended minimums will draw more current - check. 2 - A short on the main +12 volt cable from the battery to the vehicle chassis will cause the main fuse to blow.
System does not turn on
1 - Check all fuses. 2 - Check all connections. 3 - Measure the +12 volt and remote turn on voltages at the amplifier terminals. If these are non existent or low, take voltage measurements at fuse holders, distribution blocks, the head unit’s +12 volt and remote leads to localize the problem.
Noise problems
System noise can be divided into two categories, hiss, and electrical interference.
Hiss, or white noise
1 - High levels of white noise usually occurs when amplifier level controls are turned up too high - readjust according to the procedures in section ”Setting up systems after installation for best performance”
2 - Another major problem that can cause excessive hiss, is a noisy head unit - unplug the amplifier input RCA cables, and if the hiss level reduces, the source unit is at fault.
Electrical interference
The inside of an automobile is a very hostile electrical environment. The multitude of electrical systems, such as the ignition system, alternator, fuel pumps, air conditioners, to mention just a few, create radiated electrical fields, as well as noise on the +12 volt supply and ground. Remember to isolate the problem - first unplug amplifier input RCA cables, if the noise is still present, check the speaker leads, if not, plug the RCA’s back, and investigate the source driving the amplifier, one component at a time.
A ticking or whine that changes with engine RPM:
1 - This problem could be caused by radiation pickup of RCA cables too near to a fuel pump or a distributor, for instance, - relocate cables. 2 - Check that the head unit ground is connected straight to the vehicle chassis, and does not use factory wiring for ground. 3 - Try to supply the head unit with a clean +12 volt supply directly from the battery +, instead of using a supply from the in dash wiring/fusebox.
A constant whine:
This type of noise can be more difficult to pinpoint, but is usually caused by some kind of instability, causing oscillations in the system. 1 - Check all connections, especially for good grounds. 2 - Make sure that no speaker leads are shorting to exposed metal on the vehicle chassis. 3 -RCA cables are notorious for their problematic nature, so check that these are good, in particular the shield connections.
4
RM440.4
4-Channel Amplifiers
FEATURES:
- 2 Sets of RCA inputs
- LEVEL: Variable sensitivity from 0.2V to 6V
- BASS EQ: Adjustable 45Hz bass boost from 0dB to 9dB
- X-OVER: Selects internal crossover functions
- FULL: Bypasses all crossovers for full frequency operation
- LP/BP: Selects the built in variable LOW PASS filter
- HP: Selects the built in variable HIGH PASS filter
4 Channel Full Range Stereo:
- MODE: “2” indicates one set of RCA’s are being used. This will also pass signal to channels 3/4 through 1/2 inputs.
“4” indicates connecting 2 sets of RCA’s to 1/2 and 3/4 inputs.
- LINE OUTPUT: Full range RCA pass through.
Interconnect cable checklist:
- Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables. Switch setting checklist:
- 1/2CH X-OVER: FULL
- 3/4CH X-OVER: FULL MODE: “4” since 2 sets of RCA’s are connected.
CH3-4
LP/BP
HP
CH1-2
DUPE CH3-4
FULL
10
HP FREQ
HP
Hz
FULL
1K
50
50
HP FREQ
LP FREQ
Hz
Hz
3K
3K
BASS EQ
6
0
LEVEL
dB
V
0.2
9
INPUT MODE
2CH
6
LEVEL
V
4CH
0.2
CH2
CH1
CH4
CH3
MONO MIX OUT
4 CH
2 or 3 Channel System:
Here we show how to use the 4 channel amplifiers as a 3 channel unit by taking advantage of the mono bridging capability of all MB Quart amplifiers. In order to create a 2 channel system, simply follow the example to also mono bridge channel pair 1/2.
Interconnect cable checklist:
- Connect the inputs of channel pair 1/2 to a suitable stereo source, e.g. a head unit with good quality RCA cables.
- A MONO signal source is required to bridge channel pair 3/4, such as would be available from the mono sub bass output of an active crossover, whether standalone, or built into a head unit or equalizer. If you only have 1 set of RCA outputs from your headunit, you can simply connect those to the inputs for ch 1/2 and switch the MODE to 2ch.
Control checklist:
- Refer to the section “Settings for Best Performance”
Minimum final loudspeaker impedances:
- 2 ohm per channel.
GND
TURN ON
+12V
25A x 2 MAX
MIN
CH4
2
MIN
4
BRIDGED
MIN
CH3
2
MIN
CH2
2
MIN
4
BRIDGED
MIN
CH1
2
Important: Do not be tempted to connect the hot, or positive outputs, from any source together to obtain a mono signal, as this could very well damage the output stage of that source.
- It is necessary to feed the SAME signal to both left and right inputs via a Y-adapter RCA cable.
- Connect the mono speaker positive terminal to the CH3 +, and its negative terminal to CH4 ­as shown.
Switch setting checklist:
- 1/2CH X-OVER: FULL
- 3/4CH X-OVER: LP/BP Control checklist:
- Refer to the section “Settings for Best Performance”
Minimum final loudspeaker impedances:
- 2 ohm per channel in stereo mode.
- 4 ohm mono bridged.
CH3-4
MONO LINE INPUT
(Unless using procedure listed above for 2ch)
LP/BP
HP
CH1-2
DUPE CH3-4
FULL
10
HP FREQ
HP
Hz
FULL
1K
50
50
HP FREQ
LP FREQ
Hz
Hz
3K
3K
BASS EQ
6
0
LEVEL
dB
V
0.2
9
INPUT MODE
2CH
6
LEVEL
V
4CH
0.2
CH2
CH1
CH4
CH3
MONO MIX OUT
4 CH
GND
TURN ON
+12V
25A x 2 MAX
MIN
CH4
2
MIN
4
BRIDGED
MIN
CH3
2
MIN
CH2
2
MIN
4
BRIDGED
MIN
CH1
2
ONYX
5
RM740.5
5-Channel Amplifiers
FEATURES:
- 3 Sets of RCA inputs
- LEVEL: Variable sensitivity from 0.2V to 6V
- BASS EQ: Adjustable 45Hz bass boost from 0dB to 12dB
- X-OVER: Selects internal crossover functions
- FULL: Bypasses all crossovers for full frequency operation
- LP/BP: Selects the built in variable LOW PASS filter
- HP: Selects the built in variable HI PASS filter
5 Channel Discrete Operation:
You can use this configuration simply as 4 discrete full range channels, with a 5th low pass channel. All of the crossovers are bypassed , except the LOW PASS on channel 5.
Interconnect cable checklist:
Connect channel 1&2 inputs to the front output, channels 3&4 to the rear output, and channel 5 to the mono subwoofer output of a head unit or in dash equalizer.
Switch setting checklist:
- CH 1 / 2 X-OVER: FULL
- CH 3 / 4 X-OVER: FULL
CH5 REMOTE
BASS EQ
0
dB
12
CH5 LEVEL
SUBSONIC
10
6
FILTER
Hz
V
0.2
50
50
LP FREQ
Hz
HP
CH1-2
150
FULL
LP/BP
CH3-4
50
HP FREQ
HP
Hz
FULL
3K
50
LP FREQ
6
LEVEL
Hz
V
0.2
1K
50
HP FREQ
Hz
INPUT MODE
2CH
3K
4CH
6
5CH
LEVEL
V
0.2
CH2
CH1
CH4
CH3
CH5 R
CH5 L
V
FILTER
Hz
0.2
50
LP FREQ
50
Hz
CH1-2
HP FULL
150
LP/BP
HP FREQ
50
CH3-4
HP
Hz
FULL
3K
LEVEL
6
V
LP FREQ
50
Hz
0.2
1K
INPUT MODE
2CH
HP FREQ
50
Hz
5CH
4CH
CH1
CH5 L
CH3
LEVEL
CH4
CH2
6
3K
0.2
V
CH5 R
BASS EQ
CH5 LEVEL
0
6
12
dB
SUBSONIC
10
CH5 REMOTE
- INPUT MODE: “2” indicates one set of RCA’s are being used. This will also pass signal to channels 3/4 and 5 through 1/2 inputs. “4” indicates connecting 2 sets of RCA’s to 1/2 and 3/4 inputs. “5” indicates connecting 3 sets of RCA’s to channels 1/2, 3/4 and mono signal to channel 5 inputs.
MODE: “5” since 3 sets of RCA’s are connected.
Control checklist:
- Refer to the section “Settings for Best Performance”
Minimum final loudspeaker impedances:
- 2 Ohms per channel for channels 1-4
- 2 Ohm on channel 5
GND
TURN ON
+12V
40A x 2 MAX
CH5
MIN
CH4
2
MIN
4
BRIDGED
MIN
CH3
2
MIN
CH2
2
MIN
4
BRIDGED
MIN
CH1
2
Single Set of Stereo RCA’s
We will use the same basic setup on the speaker and subwoofer connections as above to illustrate an installation that only has 1 set of stereo RCA’s to connect to this amplifier. By switching the amplifier to 2CH on the INPUT MODE, you now provide signal to all channels on the amplifier. You sacrifice the ability to fade front to rear though.
Interconnect cable checklist:
Connect Stereo Left and Right RCA’s from headunit to CH1&2 RCA Inputs.
Switch setting checklist:
- CH 1 / 2 X-OVER: FULL
- CH 3 / 4 X-OVER: FULL
CH5 REMOTE
BASS EQ
0
dB
12
CH5 LEVEL
SUBSONIC
10
6
FILTER
Hz
V
0.2
50
50
LP FREQ
Hz
HP
CH1-2
150
FULL
LP/BP
CH3-4
50
HP FREQ
HP
Hz
FULL
3K
50
LP FREQ
6
LEVEL
Hz
V
0.2
1K
50
HP FREQ
Hz
INPUT MODE
2CH
3K
4CH
6
5CH
LEVEL
V
0.2
CH2
CH1
CH4
CH3
CH5 R
CH5 L
MODE: “2” since 1 set of RCA’s are connected.
Control checklist:
- Refer to the section “Settings for Best Performance”
Minimum final loudspeaker impedances:
- 2 Ohms per channel for channels 1-4
- 2 Ohm on channel 5
GND
+12V
CH4
CH3
CH2
CH1
TURN ON
40A x 2 MAX
CH5
MIN
2
MIN
4
BRIDGED
MIN
2
MIN
2
MIN
4
BRIDGED
MIN
2
6
RM1000.1
Mono Amplifiers
REMOTE
50
Hz
LP FREQ
150
10
Hz
SUBSONIC
FILTER
0
50
180
0
BASS EQ
PHASE
FEATURES:
- 1 Set of RCA inputs
- LEVEL: Variable sensitivity from 0.2V to 6V
- BASS EQ: Adjustable 45Hz bass boost from 0dB to 12dB
- SUBSONIC: Variable from 10Hz to 50Hz
- LOW PASS: Variable from 50Hz to 150Hz
- LINE OUTPUT: Full range RCA pass through.
Interconnect cable checklist: Control checklist:
Connect the inputs to a suitable source, e.g. a head unit with good quality RCA cables. Refer to the section “Settings for Best Performance”
Use at least #12 gauge speaker wiring.
REMOTE
50
LP FREQ
Hz
150
SUBSONIC
10
FILTER
Hz
50
0
PHASE
180
BASS EQ
0
dB
12
6
LEVEL
V
0.2
INPUT
OUTPUT
LEFT
RIGHT
Minimum final loudspeaker impedance: 1-Ohm.
LEFT
6
12
dB
GND
+12V
0.2
V
LEVEL
INPUT
TURN ON
30A x 4 MAX
MIN
1
RIGHT
OUTPUT
MONO
SUBWOOFER
7
8
Biggest POWER systems
V3 Products, Level 10 Performance + 1 Year Warranty
Moderate POWER systems
V2 Products, Level 7 Performance + 6 Month Warranty
Smaller POWER systems
9
V1 Products, Level 5 Performance
NOTES
10
Check out our videos of new products,
events and technical tutorials at
www.youtube.com/maxxsonicsusainc
RM440.4 / RM740.5 / RM1000.1
PART#N113
Loading...